clock INFINITI QX30 2017 User Guide

Switching the ZONE function on/off
This function is only available with automatic
climate control.
To activate:press the
button. The indi-
cator light in thebutton lights up. The
temperature setting for the driver’s side is not
adopted for the front-passenger side.
To deactivate:press the
button. The
indicator lamp in thebutton goes out.
The temperature setting for the driver’s side is
adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select theWindshield demist-
ingfunction until the windshield is clear again.
Activating theWindshield demistingfunction
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up.The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•TheWindshield demistingfunction auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while theWindshield demistingfunction is
in operation. Press the
orbutton.
Deactivating theWindshield demistingfunction:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode re-
mains deactivated.
or
Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midificationfunction.
2. Activate automatic mode
.
3. If the windows continue to mist up, activate
the
Windshield demistingfunction.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you activate air-recirculation mode, the windows
can mist up more quickly, in particular at low
temperatures. Only use air recirculation mode
briefly to prevent the windows misting up.
Display screen, heater and air conditioner, and audio system4-51

•While driving, some operations are limited
in order to prevent distracting the driver.
While driving, avoid looking at the display.
•Before changing ownership of the vehicle,
delete application data (Email data, etc.)
stored on the in-vehicle device. It is also
recommended that you call your INFINITI
customer center to notify them of change of
ownership.
•Some application services may be subject
to change or be terminated without prior
notice.
USING APPLICATIONS
NOTE
To use Apps functions on models without navi-
gation system, please complete the calendar
setting from Clock setting screen.
Clock settingsin the5. Starting and driving
section
Main operation
Push<MENU>and touch [Apps] to display the
Apps screen.
Touch the icon for the preferred application. The
selected application will be launched.
•The applications shown on the menu screen
and the display order can be customized.
App Garage Settings screenlater in this
section
•Some applications can be set to launch
automatically as the ignition switch is turned
on.
VEHICLE APPS
Vehicle Apps are unique applications developed
by INFINITI that can be downloaded and in-
stalled on the in-vehicle hardware.
NOTE
The INFINITI InTouch App must be installed and
running on a compatible smartphone in order to
download updates or use Vehicle Apps that re-
quire a network connection. SeeGetting user ID
and passwordlater in this section.App Garage screen
1. Push<MENU>and touch [Apps].
2. Touch [App Garage].
Available settings
•[Vehicle Apps Manager] (if equipped)
Install, uninstall, and update the Vehicle
Apps application.
•[App Garage Settings]
Select icons to be displayed on the menu
screen and change the auto start and net-
work connection settings.
•Available application list
Display downloaded Vehicle Apps applica-
tions and selected Mobile Apps applications.
NAA1672
4-100Display screen, heater and air conditioner, and audio system

MAJOR APPS AVAILABLE FOR USE IN THIS SYSTEM
The major applications currently available for INFINITI InTouch are introduced here.
Note that the applications are subject to updates and changes.
Apps Descriptions
[Maintenance Note] You can check maintenance items inside the vehicle at your convenience.
[Calendar]* (if equipped) The day’s schedule can be checked. The schedule in the [Calendar] works with web-based services.
[Email]* (if equipped) The Email account you use can also be accessed through the vehicle system. You will be informed when a new incoming message
is received. This application works with web-based services.
[Compass]
(models with navigation system)The current traveling direction of the vehicle is shown in various kinds of skins.
Accurate information cannot be provided if GPS position information cannot be obtained.
[Clock] [Clock] shows the current time in various kinds of skins.
Mobile Apps Many popular applications you usually use on your smartphone can also be used in your vehicle.
After registering a subscription in “INFINITI InTouch Apps” you can use these applications by operating the in-vehicle display.
Applications such as Facebook, etc.
*: Requires an account to be set up. To use [Calendar], [Email] and Mobile Apps, INFINITI InTouch Apps must be downloaded to your smartphone.
WARNING
•Look at the display screen only briefly while
driving. Keep your eyes on the road. Inatten-
tive driving may lead to a crash resulting in
serious injuries or death.
NOTE
When Email service and calendar schedule infor-
mation are displayed on the in-vehicle display,the system controls the display based on the
in-vehicle profiles (user ID and password).
Therefore, users are required to create a profile
to make use of Email and calendar services.
IMPORTANT:
A PIN code can be used so that other people
cannot see your Email and calendar apps. When
the engine is turned OFF and then ON again, the
PIN code has to be entered.After the PIN code is entered, regardless of
whether your smartphone is connected to the
vehicle or not, Email and calender apps will be
viewable until the engine is turned OFF. When
the system is set to valet parking, or the relevant
account is erased, Email and schedule will be
erased from the system.
Display screen, heater and air conditioner, and audio system4-103

Setting item Result
[Navigation]* Display the Navigation setting screen.
Refer to the Navigation Owner’s Manual for details.
[Audio]Display the Audio settings screen.
SeeAudio settingsearlier in this section
[Screen] Set the screen display to the preferred settings.
SeeScreen settingsearlier in this section
[Volume Adjustment] Set the volume for each item.
SeeVolume settingsearlier in this section
[Clock]Set the Clock to your preferred settings.
SeeClock settingsearlier in this section
[InTouch Services] Set INFINITI InTouch
TMServices.
Refer to the Navigation Owner’s Manual for details.
[Voice recognition] Set Minimize Voice Feedback to on/off and the audio setting for voice recognition use.
[Camera/Sonar] Set the camera and parking sensor (sonar) to the preferred settings.
SeeAround View Monitor settingearlier in this section
[Other] [Language] Set the language to the preferred settings.
SeeLanguage settingsearlier in this section
[Keyboard Type] Set the Keyboard Type to [QWERTY] or [ABC].
[Low on Fuel Alert] Set the fuel low notification to on/off.
[Software information] Display the software information.
* : Models with navigation system.
NOTE
•The displayed items vary depending on the
vehicle model and equipped options.
•The order of displayed items can be sorted.
Display screen, heater and air conditioner, and audio system4-123

The INFINITI Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll road
device or automated payment device on the key
ring. Restart the engine using the following
procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK
position and wait approximately 5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the device
(which may have caused the interference)
separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
0OFF position
1ACC position
2ON position
3START position
WARNING
Never remove the key or turn the ignition
switch to the OFF position while driving. The
steering wheel will lock and could cause the
driver to lose control of the vehicle. This could
result in serious vehicle damage or personal
injury.
CAUTION
Use electrical accessories with the engine run-
ning to avoid discharging the vehicle battery.
If you must use accessories while the engine is
not running, do not use them for extended pe-
riods of time and do not use multiple electrical
accessories at the same time.
The switch includes an anti-theft steering lock
device.
STEERING LOCK
To lock the steering wheel
1. Turn the key to the OFF position.
2. Remove the key from the ignition switch.
3. Turn the steering wheel 1/6 of a turn
clockwise from the straight up position.
To unlock the steering wheel
1. Insert the key into the ignition switch.
2. Gently turn the key while rotating the
steering wheel slightly right and left.
NPA1483
INFINITI VEHICLE IMMOBILIZER SYSTEM IGNITION SWITCH
5-14Starting and driving

2. Align the center of both the jack head2and the notches at the jack-up point3as
shown.
3. Fit the groove of the jack head between the
two notches as shown.4. Loosen each wheel bolt by one or two turns
counterclockwise with the wheel wrench.
Do not remove the wheel bolts until the tire is
off the ground.
Models with wheel lock bolts (if equipped) :
If the wheel is equipped with a wheel lock
bolt, insert the wheel lock key
1and
loosen it as previously described.
The wheel lock bolt can only be removed
with the wheel lock key. A key number is
necessary if you need to duplicate the wheel
lock key.Record the key number as shown on the key
code card on the “Security information”
page at the end of this manual and keep it in
a safe place, not in the vehicle. If you lose
the wheel lock key, it is recommended you
see your INFINITI retailer for a duplicate with
the original wheel lock key code.
Make sure to keep the lock key in the
vehicle. Otherwise, wheels cannot be re-
moved and the service cannot be performed.
NCE449NCE143Z
In case of emergency6-7

5. To lift the vehicle, securely hold and turn the
ratchet handle
1clockwise as shown.
6. Carefully raise the vehicle until the tire
clears the ground.
7. Remove the wheel bolts, then remove the
wheel with the flat tire.
WARNING
The wheel is heavy. Be sure that your feet are
clear of the wheel and use gloves as necessary
to avoid injury.
Installing the wheel
WARNING
•A temporary use spare wheel and tire is
designed for emergency use.
•Never use wheel bolts other than those
provided with your vehicle. Incorrect wheel
bolts or improperly tightened wheel bolts
may cause the wheel to become loose or
come off. This could cause an accident.
•Never use oil or grease on the wheel bolts.
This may cause the wheel bolts to become
loose.ATighten
BLoosen
1. Clean any mud or dirt from the surface
between the wheel and the hub.
2. Carefully fit the wheel and tighten the wheel
bolts with your fingers. Check that all the
wheel bolts contact the wheel surface hori-
zontally and on the bevelled side.
Models with wheel lock bolt (if equipped):
Insert the wheel lock key into the wheel lock
bolt and tighten into the wheel finger tight.
3. With the wheel wrench, tighten the wheel
bolts alternately and evenly in the sequence
as illustrated (
1-5) until they are tight.
4. Lower the vehicle slowly until the tire
touches the ground.
NCE449NCE435
6-8In case of emergency

5. Tighten the wheel bolts securely using the
wheel wrench in the sequence as illustrated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel
bolt tightening torque: 96 ft-lb (130 N•m, 13
kg-m)
As soon as possible, tighten the wheel bolts to
the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifica-
tion at each maintenance interval.
Adjust the tire pressure to the COLD pressure.
COLD pressure is the tire pressure as measured
after the vehicle has been parked for three hours
or more or driven for less than 1 mile (1.6 km).
COLD tire pressures are shown on the tire and
loading information label affixed to the driver’s
side center pillar.
Wheel lock bolts(if equipped)
In order to prevent theft, the specially designed
wheel lock bolt is installed to each wheel. The
wheel lock bolt cannot be removed with the
commonly used tools.
When removing tires, use the lock key provided
with your vehicle.Removing the wheel lock bolt
:
1. Insert the wheel lock key1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the
wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the wheel
lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For de-
tails, seeInstalling the wheelearlier in
this section.NOTE
•The wheel lock bolt has an individual code.
A wheel lock key with other than the indi-
vidual code cannot remove the wheel lock
bolt. If you lose the wheel lock key, it is
recommended you contact an INFINITI re-
tailer for a duplicate with the original wheel
lock key code.
•Record the key number and keep it in a safe
place, not in the vehicle.
•When you ask for a service at an INFINITI
retailer, make sure to keep the lock key in
the vehicle. Otherwise, wheels cannot be
removed and the service cannot be per-
formed.
NCE143Z
In case of emergency6-9

CAUTION
•Never use any cooling system additives
such as radiator sealer. Additives may clog
the cooling system and cause damage to
the engine, transmission and/or cooling
system.
•When adding or replacing coolant, be sure
to use only INFINITI Genuine Engine Cool-
ant, BASF Glysantin G40 or equivalent in its
quality. The use of other types of engine
coolant may damage the engine cooling
system.
CHECKING ENGINE COOLANT LEVEL
NOTE
The coolant level must only be checked and cor-
rected when the engine is cold.
1. Park the vehicle on a level surface.
Only check the coolant level if the vehicle is
on a level surface and the engine is cold.
2. Slowly turn cap
1half a turn counter-
clockwise to allow excess pressure to es-
cape.
3. Turn cap
1further counter-clockwise and
remove it.
If the coolant is at the level of marker bar
3in the filler neck when cold, there is enough
coolant in coolant expansion tank
2.4. If necessary, top up with INFINITI Genuine
Engine Coolant, BASF Glysantin G40 or
equivalent in its quality.
5. Replace cap
1and turn it clockwise as far
as it will go.
If the cooling system frequently requires cool-
ant, have it checked. It is recommended that you
visit an INFINITI retailer for this service.
NDI1602
8-4Do-it-yourself

1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it
counterclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by
turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer toChanging
engine oil filterlater in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new
washer. Securely tighten the drain plug with
a wrench. Do not use excessive force. Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through
the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer toRecommended fluids/
lubricants and capacitiesin the9. Maintenance
and Schedulessection.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around
the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10
minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and apply
the parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
5. Wipe the engine oil filter sealing surface
with a clean rag.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself