Wing mirror INFINITI QX30 2018 Owner's Manual

•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press theorbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the <OK> button to save the setting.
When the [Surround Lighting] function is
activated, the light cone and the area
around the vehicle are displayed in orange
in the vehicle information display
6. Press the <OK> button to confirm the set-
ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni-
tion switch to the OFF position.
2. Switch the ignition switch to the ON po-
sition.
The exterior lighting delayed switch-off is
deactivated.Delayed switch-off of the exterior lighting
is reactivated the next time you start the
engine.
Depending on your vehicle&#39;s equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Activating/deactivating the interior light-
ing delay:
If you activate the [Interior Lighting Delay]
function, the interior lighting remains on for
20 seconds after you remove the key from
the ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.4. Press the
orbutton to select
the [Interior Lighting Delay] function. If
the [Interior lighting delayed switch-off]
function has been switched on, the vehicle
interior is displayed in orange in the ve-
hicle information display
5. Press the <OK> button to save the setting.
Vehicle
Setting permanent speed limiter:
You can set permanent speed limiter using
the [Limit Speed (Winter Tires)] function.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Limit Speed (Winter Tires)] function.
You will see the selected setting.
5. Press <OK> to confirm.
6. Press the
orbutton to adjust
permanent speed limiter in increments of
ten ([150 mph] to [100 mph]), [240 km/h]
to [160 km/h]). The [Off] setting switches
permanent speed limiter off).
Instruments and controls2-27

The defroster switchBoperates when the
ignition switch is in the ON position for the
rear window, and (if equipped) for the outside
rear view mirrors.
The defroster is used to reduce the moisture,
fog or frost on the rear window surface and
on the outside mirror surface to improve the
rear view.
When the defroster switch
is pushed,
the indicator light illuminates and the de-
froster operates for several minutes. After
the preset time has passed, the defroster will
turn off automatically. To turn off the de-
froster manually, push the defroster switch
again, and the indicator light turns off.
CAUTION
•When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.
•When operating the defroster con-
tinuously, be sure to start the engine.
Otherwise, it may cause the battery to
discharge.
•When cleaning the inner side of the win-
dow, be careful not to scratch or dam-
age the electrical conductors on the sur-
face of the window.The windshield de-icer switch (defogger
switch)
Aoperates when the ignition switch
is in the ON position.
You can use this function to defrost the wind-
shield or to demist the inside of the wind-
shield and the side windows
NOTE
You should only select the windshield de-icer
function until the windshield is clear again.
When the switch
is pushed, the indica-
tor light in the switch illuminates. The climate
control system switches to the following
functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air recirculation mode off
NAA1659NAA1659
REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCHWINDSHIELD DE-ICER SWITCH (IF
EQUIPPED)
2-64Instruments and controls

HIGH BEAM ASSIST (LED
HEADLIGHT ONLY)
You can use this function to set the head-
lights to change between low beam and high
beam automatically. The system recognizes
vehicles with their lights on, either approach-
ing from the opposite direction or traveling in
front of your vehicle, and consequently
switches the headlights from high beam to
low beam.
The system automatically adapts the low
beam headlight range depending on the dis-
tance to the other vehicle. Once the system
no longer detects any other vehicles, it
switches on the high beam headlights again.
The system&#39;s optical sensor is located behind
the windshield near the overhead control
panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe
driving operation. The driver should re-
main alert at all times, ensure safe driv-
ing practices and switch the high beams
and low beam manually when necessary.
•The high beam or low beam may not
switch automatically under the follow-
ing conditions. Switch the high beam
and low beam manually.
–During bad weather (rain, fog, snow,
wind, etc.).
–When a light source similar to a head-
light or tail light is in the vicinity of
the vehicle.
–When the headlights of the oncoming
vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials
on the lights, or when the light beam
is out of position.
–When there is a sudden, continuous
change in brightness.
–When driving on a road that passes
over rolling hills, or a road that has
level differences.
–When driving on a road with many
curves.–When a sign or mirror-like surface is
reflecting intense light towards the
front of the vehicle.
–When the container, etc. being towed
by a leading vehicle is reflecting in-
tense light.
–When a headlight on your vehicle is
damaged or dirty.
–When the vehicle is leaning at an
angle due to a punctured tire, being
towed, etc.
•The timing of switching the low beam
and high beam may change under the
following situations.
–The brightness of the headlights of
the oncoming vehicle or leading ve-
hicle.
–The movement and direction of the
oncoming vehicle and the leading ve-
hicle.
–When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
–When the oncoming vehicle or the
leading vehicle is a two-wheeled ve-
hicle.
–Road conditions (incline, curve, the
road surface, etc.).
–The number of passengers and the
amount of luggage.
NDS595
Instruments and controls2-69

5. Press and hold button6on the hand held
transmitter until indicator light
1lights
up green. When indicator light
1: lights
up green: programing is finished.
When indicator light
1flashes green:
programing was successful. The next step
is to synchronize the rolling code.
6. Release button
6on the hand held trans-
mitter
5for the garage door drive sys-
tem.
If indicator light
1lights up red: repeat
the programing procedure for the corre-
sponding button on the rear-view mirror.
When doing so, vary the distance be-
tween the hand held transmitter
5and
the rear-view mirror.
The required distance between the hand
held transmitter
5and the integrated ga-
rage door opener depends on the garage
door drive system. Several attempts might
be necessary. You should test every posi-
tion for at least 25 seconds before trying
another position.
Synchronizing the rolling code
If the garage door system uses a rolling code,
you will also have to synchronize the garage
door system with the integrated garage door
opener in the rear-view mirror. To do this you
will need to use the programing button on thedoor drive control panel. The programing
button may be positioned at different loca-
tions depending on the manufacturer. It is
usually located on the door drive unit on the
garage ceiling.
Familiarize yourself with the garage door
drive operating instructions before carrying
out the following steps.
Your vehicle must be within reach of the ga-
rage door or gate opener drive. Make sure
that neither your vehicle nor any persons/
objects are present within the sweep of the
door or gate.
1. Turn the ignition key to the ON position.
2. Get out of the vehicle.
3. Press the programing button on the door
drive unit.
Usually, you now have 30 seconds to ini-
tiate the next step.
4. Get into the vehicle.
5. Press previously programed button
2,3or4on the HomeLink® until the door
closes.
The rolling code synchronization is then
complete.
If you live in Canada
Canadian radio frequency laws require a
&#34;break&#34; (or interruption) of the transmission
signals after broadcasting for a few seconds.
Therefore, these signals may not last long
enough for the integrated garage door
opener. The signal is not recognized during
programing. Comparable with Canadian law,
some U.S. garage door openers also feature a
&#34;break&#34;.
Proceed as follows:
•If you live in Canada
•If you have difficulties programing the ga-
rage door opener (regardless of where you
live) when using the programing steps.
1. Press and hold one of buttons
2to4on
the HomeLink®. After a short time, indi-
cator light
1lights up yellow.
2. Release the button.
Indicator light
1flashes yellow.
3. Press button
6of the hand held trans-
mitter
5for two seconds, then release it
for two seconds.
4. Press button
6again for two seconds.
5. Repeat this sequence on button
6of the
hand held transmitter
5until indicator
light
1lights up green.
Instruments and controls2-91

1. To block out glare from the front, swing
down the sun visor
1.
2. To block glare from the side, remove the
sun visor from the center mount and
swing the visor to the side
2.
VANITY MIRROR
To use the front vanity mirror3, pull down
the sun visor
1and pull up the cover4.
AUTOMATIC ANTI-GLARE REAR
VIEW MIRROR
The inside mirror is designed so that it auto-
matically dims according to the intensity of the
headlights of the vehicle following you. The
automatic anti-glare feature operates only
when the ignition switch is in the ON position.
It will not operate if reverse gear is engaged or
if the interior lighting is switched on.
OUTSIDE MIRRORS
The driver&#39;s-side outside mirror is designed so
that it automatically dims according to the in-
tensity of the headlights of the vehicle follow-
ing you. The automatic anti-glare feature op-
erates only when the ignition switch is in the
ON position. It will not operate if reverse gear
is engaged or if the interior lighting is switched
on.SIC2872
NIC2676NDI1630
SUN VISORSMIRRORS
3-18Pre-driving checks and adjustments

seat. If someone becomes trapped, imme-
diately release the memory function posi-
tion button The adjustment is stopped.
•If children activate the memory func-
tion, they could become trapped, espe-
cially if they are unattended. There is a
risk of injury.
When leaving the vehicle, always take
the key with you and lock the vehicle.
Never leave children unattended in the
vehicle.
The memory function can be used at any
time, e.g. even when the key isn&#39;t in the igni-
tion lock.
STORING SETTINGS
With the memory function, you can store up
to three different settings, for example, for
three different people. The following settings
are stored as a single memory preset:
•Seat and seatback position
•Driver&#39;s side: position of the exterior mir-
rors on the driver&#39;s and front-passenger
sides.
To store settings:
1. Adjust the seat (see &#34;Power seat adjust-
ment&#34;).
2. Adjust the exterior mirror on the driver&#39;s
side (see &#34;Adjusting&#34;).
3. Briefly press the M memory button
1,
and then press preset position button 1, 2
or 3
2within three seconds.
The settings are stored in the selected
preset position. A tone sounds when the
settings have been completed.
CALLING UP A STORED SETTING
Press and hold the relevant preset position
button 1, 2 or 3 until the seat and exterior
mirrors are in the stored position.
NOTE
The setting procedure is interrupted as soon
as you release the storage position button.
3-22Pre-driving checks and adjustments

ARearView Monitor display
BINFINITI controller
C<MENU> button
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the RearView Moni-
tor could result in serious injury or death.
•The RearView Monitor is a convenience
feature but it is not a substitute for
proper backing up. Always turn and look
out the windows, and check mirrors to
be sure that it is safe to move before
operating the vehicle. Always back up
slowly.
•The system is designed as an aid to the
driver in showing large stationary ob-
jects directly behind the vehicle, to help
avoid damaging the vehicle.
•The distance guide line and the vehicle
width line should be used as a reference
only when the vehicle is on a level paved
surface. The distance viewed on the
monitor is for reference only and may be
different than the actual distance be-
tween the vehicle and displayed objects.
NSD627
REARVIEW MONITOR (IF SO
EQUIPPED)
Display screen, heater and air conditioner, and audio system4-3

A[Settings] key
B<MENU> button
AROUND VIEW® MONITOR
SETTING
Around View® Monitor settings can be
changed using the following procedure:1. Push the<MENU>button
Bon the
INFINITI Controller and touch [Settings]
Ain the vehicle information display.
2. Touch [Camera]/[Sonar]
3. Touch [Camera]
4. Touch [Moving Object Detection]
Activate or deactivate the Moving Object
Detection (MOD) mode.
AROUND VIEW® MONITOR
SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for
Around View® Monitor. Failure to operate
the vehicle in accordance with these sys-
tem limitations could result in serious in-
jury or death.
•Do not use the Around View® Monitor
with the outside mirror in the stored po-
sition, and make sure that the lift gate is
securely closed when operating the ve-
hicle using the Around View® Monitor.
•The apparent distance between objects
viewed on the Around View® Monitor
differs from the actual distance.
NSD628
4-20Display screen, heater and air conditioner, and audio system

•The cameras are installed on the front
grille, the outside mirrors and above the
rear license plate. Do not put anything
on the cameras.
•When washing the vehicle with high-
pressure water, be sure not to spray it
around the cameras. Otherwise, water
may enter the camera unit causing wa-
ter condensation on the lens, a malfunc-
tion, fire or an electric shock.
•Do not strike the cameras. They are pre-
cision instruments. Doing so could cause
a malfunction or cause damage resulting
in a fire or an electric shock.
The following are operating limitations and
do not represent a system malfunction:
•There may be a delay when switching be-
tween views.
•When the temperature is extremely high or
low, the screen may not display objects
clearly.
•When strong light is directly shines on the
camera, objects may not be displayed
clearly.
•The screen may flicker under fluorescent
light.
•The colors of objects on the Around
View® Monitor may differ somewhat
from the actual color of objects.
•Objects on the monitor may not be clear
and the color of the object may differ in a
dark environment.
•There may be differences in sharpness be-
tween each camera view of the bird’s-eye
view.
•Do not use wax on the camera lens. Wipe
off any wax with a clean cloth that has
been dampened with a diluted mild clean-
ing agent, then wipe with a dry cloth.
There are some areas where the system will not
show objects and the system does not warn of
moving objects. When in the front or the rear
view display, an object below the bumper or on
the ground may not be viewed
1. When in the
bird&#39;s-eye view, a tall object near the seam
3of the camera viewing areas will not appear
in the monitor
2.
NAA1639
Display screen, heater and air conditioner, and audio system4-21

–When strong light such as another
vehicle’s headlight or sunlight is pres-
ent.
–When camera orientation is not in its
usual position, such as when mirror is
folded.
–When there is dirt, water drops or
snow on the camera lens.
–When the position of the moving ob-
jects in the display is not changed.
•The MOD system might detect some-
thing like flowing water droplets on the
camera lens, white smoke from the muf-
fler, moving shadows, etc.
•The MOD system may not function
properly depending on the speed, direc-
tion, distance or shape of the moving
objects.
•If your vehicle sustains damage to the
parts where the camera is installed,
leaving it misaligned or bent, the sensing
zone may be altered and the MOD sys-
tem may not detect objects properly.
•When the temperature is extremely high
or low, the screen may not display ob-
jects clearly. This is not a malfunction.
MOD MALFUNCTION
The blue MOD icon will change to orange if
one of the following has occurred
•When the system is malfunctioning.
•When the component temperature
reaches a high level (icon will blink).
If the icon light continues to illuminate or-
ange, have the MOD system checked. It is
recommended you visit an INFINITI retailer
for this service.
SYSTEM MAINTENANCE
CAUTION
•Do not use alcohol, benzine or thinner to
clean the cameras. This will cause discol-
oration. To clean the cameras, wipe with
a cloth dampened with diluted mild
cleaning agent and then wipe with a dry
cloth.
•Do not damage the cameras as the moni-
tor screen may be adversely affected.
If dirt, rain or snow accumulates on any of the
cameras
1, the MOD system may not oper-
ate properly. Clean the cameras by wiping
with a cloth dampened with a diluted mild
cleaning agent and then wiping with a dry
cloth.
NAA1689
Display screen, heater and air conditioner, and audio system4-27