ignition INFINITI QX30 2018 Owner's Manual

If an abnormality occurs in the system, the
VDC system function will be canceled, but
the vehicle is still driveable. For additional
information, see "Vehicle Dynamic Control
(VDC) system" in the "5. Starting and driving"
section.
WARNING
VDC should remain on unless freeing a ve-
hicle from mud or snow.
While the VDC system is operating, you
might feel a slight vibration or hear the sys-
tem working when starting the vehicle or ac-
celerating, but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights
are switched on (see " Fog light switch (If so
equipped)" later in this section).
High beam assist indicator
light (if equipped)
The indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beam selected. This indicates that the high
beam assist system is operational. (See
2-64.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the
low beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (see " Fog light switch (If so
equipped)" later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, see "Headlight
and turn signal switches" later in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light () located on the center console above
the shift lever will illuminate when the front
passenger air bag is turned OFF. When the
front passenger air bag is turned on, the front
passenger air bag status light ON (
) will
illuminate.
For more details, see "Front passenger air
bag and status light" in the "1. Safety — seats,
seat belts and supplemental restraint system"
section.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver's
door is opened if the side lights are on. Turn
the headlight control switch off before leav-
ing the vehicle.
Seat belt reminder chime
A chime will sound for approximately 120
seconds if the vehicle's speed exceeds 16
2-14Instruments and controls

MPH (25 km/h) and the driver's seat belt or
front passenger's seat belt, if occupied is not
securely fastened. See "Seat belt warning
light" in the "1. Safety — seats, seat belts and
supplemental restraint system" section.
Idle Stop/Start System reminder
chime (if equipped)
The engine will shift to the normal stopped
state if any of the following operations is
made during Idle Stop/Start System activa-
tion, and the Idle Stop/Start System chime
will sound if:
– The vehicle engine hood is open.When the above condition continues for over
3 minutes the Idle Stop/Start System chime
will sound in 5-minute intervals as a reminder
to prevent the possibility of a discharged bat-
tery. Use the ignition switch to turn off the
engine.
Close the hood or the driver’s door, or fasten
the seat belt then restart the engine using the
ignition switch.
For more information, see " Idle Stop/Start
System (if equipped)" in the "5. Starting and
driving" section.
The vehicle information display
1is located
between the tachometer and the
speedometer.
NIC2751
VEHICLE INFORMATION DISPLAY
Instruments and controls2-15

Trip computer [From start] or [From reset]:
1Distance
2Driving time
3Average speed
4Average fuel consumption
Press the
orbutton on the steer-
ing wheel to select the [Trip] menu.
Press the
orbutton to select
[From start] or [From reset].
The values in the [From start] submenu are
calculated from the start of a journey whilst
the values in the [From reset] submenu are
calculated from the last time the submenu
was reset. The [From start] trip computer is automati-
cally reset when:
•The ignition has been switched off for
more than four hours.
•999 hours have been exceeded.
•9999 kilometers have been exceeded.
The [From reset] trip computer is automati-
cally reset if the value exceeds 9999 hours or
99999 kilometers.
Displaying the range and current fuel con-
sumption:
Press the
orbutton on the steer-
ing wheel to select the [Trip] menu.
Press the
orbutton to select
approximate range
1and current fuel con-
sumption
2.
Approximate range
1that can be covered is
calculated according to your current driving
style and the amount of fuel in the tank. If
there is only a small amount of fuel left in the
fuel tank, the display shows a vehicle being
refuelled instead of approximate range
1.
NIC2711NIC2713
Instruments and controls2-17

Setting the brightness of the ambient light-
ing:
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with <OK>. If you change the setting, conversion does
not take place until the next time the ve-
hicle is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to
[Level 5] (bright).
7. Press the <OK> or
button to save the
setting. Activating/deactivating the surround
lighting and exterior lighting delayed
switch-off:
If you have activated the Surround lighting
function and the light switch is set to
<AUTO>, the following functions are acti-
vated when it is dark:
•Surround lighting: the exterior lighting re-
mains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and auto-
matic headlight mode is activated .
•Exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you
close all the doors and the lift gate, the
exterior lighting goes off after 15 seconds.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Surround Lighting] function.
5. Press the <OK> button to save the setting. When the [Surround Lighting] function is
activated, the light cone and the area around the vehicle are displayed in orange
in the vehicle information display
6. Press the <OK> button to confirm the set- ting.
Deactivating delayed switch-off of the exte-
rior lighting temporarily:
1. Before leaving the vehicle, switch the igni- tion switch to the OFF position.
2. Switch the ignition switch to the ON po- sition.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the en-
gine.
Depending on your vehicle&#39;s equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the fol-
lowing light up:
•Side lights
•Fog lights
•Low beam headlights
•Daytime driving lights
•Surround lighting in the exterior mirrors
Instruments and controls2-27

Activating/deactivating the interior light-
ing delay:
If you activate the [Interior Lighting Delay]
function, the interior lighting remains on for
20 seconds after you remove the key from
the ignition lock.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Interior Lighting Delay] function. If
the [Interior lighting delayed switch-off]
function has been switched on, the vehicle
interior is displayed in orange in the ve-
hicle information display
5. Press the <OK> button to save the setting.
Vehicle
Setting permanent speed limiter:
You can set permanent speed limiter using
the [Limit Speed (Winter Tires)] function.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu. 2. Press the
orbutton to select
[Vehicle] submenu.
3. Press <OK> to confirm.
4. Press the
orbutton to select
the [Limit Speed (Winter Tires)] function.
You will see the selected setting.
5. Press <OK> to confirm.
6. Press the
orbutton to adjust
permanent speed limiter in increments of
ten ([150 mph] to [100 mph]), [240
km/h] to [160 km/h]). The [Off] setting
switches permanent speed limiter off).
7. Press the <OK> or
button to store
the entry.
Activating/deactivating the acoustic lock-
ing confirmation:
If you switch on the [Acoustic Lock Feed-
back] function, an acoustic signal sounds
when you lock the vehicle.
1. Press the
orbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Vehicle] submenu.
3. Press <OK> to confirm. 4. Press the
orbutton to select
the [Acoustic Lock Feedback] function.
If the [Acoustic Lock Feedback] function
is activated, the
symbol in the ve-
hicle information display lights up orange.
5. Press the <OK> button to save the setting.
Convenience
Switching the [Fold Mirrors in when Lock-
ing] function on/off:
This function is only available when the ve-
hicle is equipped with the electrical fold-in
function.
When you activate the [Fold Mirrors in when
Locking] function, the exterior mirrors are
folded in when the vehicle is locked. If you
unlock the vehicle and then open the driver&#39;s
or front passenger door, the exterior mirrors
fold out again.
If you have switched on the [Fold Mirrors in
when Locking] function and you fold in the
exterior mirrors using the button on the door
(see &#34;Folding&#34; in the &#34;3. Pre-driving checks
and adjustments&#34; section), they will not fold
out automatically. The exterior mirrors can
then only be folded out using the button on
the door.
2-28Instruments and controls

1. Press theorbutton on the
steering wheel to select the [Settings]
menu.
2. Press the
orbutton to select
[Convenience] submenu.
3. Press <OK> to confirm.
4.
Press theorbutton to select the
[Fold Mirrors in when Locking] function.
If the [Fold Mirrors in when Locking]
function is activated, the vehicle&#39;s exterior
mirror is shown in orange in the vehicle
information display.
5. Press the <OK> button to save the setting.
Resetting to factory settings
1.Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press theorbutton to select
[Factory Setting] submenu.
3. Press <OK> to confirm.
The [Reset All Settings?] message appears.
4. Press theorbutton to select
[No] or [Yes].
5.
ress the <OK> button to confirm the selec-
tion.
If you have selected [Yes], the vehicle in-
formation display shows a confirmation
message. For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must switch
the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner&#39;s Manual and may
differ from the symbols in the vehicle infor-
mation display.
Certain display messages are accompanied
by an audible warning tone or a continuous
tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been
rectified, these display messages are deleted as
well.
When you stop and park the vehicle, please
observe the notes on parking (see &#34;Parking&#34; in
the &#34;5. Starting and driving&#34; section).
Hiding display messages
Press the <OK> orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for
the messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can
call up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service]
menu.
If there are display messages, the vehicle
information display shows [2 messages],
for example.
2. Press the
orbutton to select
the entry, e.g. [2 messages].
3. Press <OK> to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

MessagePossible causes/consequences and solutions
[Inoperative See
Operator&#39;s Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Inoperative See Opera-
tor&#39;s Manual]EBD (Electronic Brake Force Distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic
Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the
,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could therefore
lock if you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking
situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to
Release the Parking
Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
2-32Instruments and controls

MessagePossible causes/consequences and solutions
[Please Release Parking
Brake]The redindicator light flashes and a warning tone sounds. A condition for automatic release of the electric parking brake is not
fulfilled (see &#34; Applying automatically (vehicles with automatic transmission)&#34; in the &#34;5. Starting and driving&#34; section).
You are driving with the electric parking brake applied.
Release the electric parking brake manually.
The red
indicator light flashes and a warning tone sounds.
You are making an emergency stop using the electric parking brake (see &#34;Emergency braking&#34; in the &#34;5. Starting and driving&#34; section)
[Parking Brake See
Operator&#39;s Manual] The yellowwarning light lights up.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off.
2. Press the electric parking brake handle for at least ten seconds.
3. Press the P (Park) button.
4. Have the system checked. It is recommended you consult an INFINITI retailer.
The yellow
warning light and the redindicator light are lit.
The electric parking brake is malfunctioning.
To release:
1. Switch the ignition off and turn it back on.
2. Release the electric parking brake manually.or
3. Release the electric parking brake automatically (see &#34; Applying automatically (vehicles with automatic transmission)&#34; in the &#34;5.
Starting and driving&#34; section).
If the electric parking brake still cannot be released: DO NOT drive on. It is recommended you consult an INFINITI retailer.
Instruments and controls2-33

MessagePossible causes/consequences and solutions
The yellow
warning light is lit. The redindicator light flashes.
The electric parking brake is malfunctioning.
To release:
1. Switch the ignition off and turn it back on.
2. Release the electric parking brake manually.or
To apply:
1. Switch the ignition off and turn it back on.
2. Apply the electric parking brake manually.
If the red
. indicator light continues to flash:
1 DO NOT drive on
2. Secure the vehicle against rolling away
3. Press the P (Park) button.
4. Turn the front wheels towards the curb.
It is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake has been
applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off and turn it back on.
2. Apply the electric parking brake manually.If it is not possible to apply the electric parking brake:
3. Press the P (Park) button.
It is recommended you consult an INFINITI retailer.
If it is not possible to release the electric parking brake:
Release the electric parking brake automatically (see &#34; Applying automatically (vehicles with automatic transmission)&#34; in the &#34;5.
Starting and driving&#34; section).
If the electric parking: brake still cannot be released, it is recommended you consult an INFINITI retailer.
2-34Instruments and controls

MessagePossible causes/consequences and solutions
The yellow
warning light is lit. If you manually apply or release the electric parking brake, the redindicator light flashes.
The electric parking brake is malfunctioning. It is not possible to apply the electric parking brake manually.
or
Insert the seat belt in the belt buckle and accelerate slightly more when pulling away.
Press the P (Park) button, as the electric parking brake is not applied automatically.
It is recommended you consult an INFINITI retailer.
If you do not wish the electric parking brake to be applied, leave the ignition switched on, e. g. when washing the vehicle in an
automatic car wash or when having the vehicle towed.
[Parking Brake
Inoperative] The yellowwarning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake has
been applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning, e.g. because of overvoltage or undervoltage.
1. Rectify the cause of the overvoltage or undervoltage, e.g. by charging the battery or restarting the engine.
2. Apply or release the electric parking brake.
If the electric parking brake still cannot be applied or released:
1. Switch the ignition off and turn it back on.
2. Apply or release the electric parking brake manually.
If the electric parking brake still cannot be applied or released, it is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes.
It is not possible to apply the electric parking brake manually.
1. Press the P (Park) button.
Consult an INFINITI retailer.
[Brake Immediately] A tone may also sound at regular intervals. If you attempt to lock the vehicle, the tone becomes louder.
You cannot start the engine.
1. Paying attention to the traffic situation, immediately depress the brake pedal firmly and hold until the display message disappears.
2. Secure the vehicle against rolling away. You can restart the engine.
Instruments and controls2-35