start stop button INFINITI QX30 2018 Owner's Manual

display. The set distance to a slower-moving
vehicle in front will then not be maintained.
You will be driving at the speed you deter-
mine by the position of the accelerator pedal.
You can also activate ICC when stationary.
The lowest speed that can be set is 20 MPH
(30 km/h).
Stopping
WARNING
•To help avoid risk of injury or death
through unintended operation of the
vehicle and/or its systems, do not leave
children, people who require the assis-
tance of others, or pets unattended in
your vehicle.
•The ICC system should only be used to
keep the vehicle stationary when the
driver is actively using the system.
When parking the vehicle, make sure to
turn OFF the ICC system, use the brake,
press the PARK (P) button, and place
the ignition switch in the LOCK position
prior to exiting the vehicle. Failure to do
so could lead to serious injury or death.
The ICC system will not hold the vehicle
in place after coming to a stop when any
of the following conditions occur: –
There is a malfunction in the system
or in the voltage supply.
– The ICC system has been deactivated
with the cruise control lever, e. g. by a
vehicle occupant.
– The accelerator pedal has been de-
pressed, e.g. by a vehicle occupant.
For further information on deactivating the
ICC system, see "ICC switch (cruise control
lever)" earlier in this section
If the ICC system detects that the vehicle in
front is stopping, it brakes your vehicle until it
is stationary (within the braking limitations of
the system).
Once your vehicle is stationary, it remains
stationary and you do not need to depress
the brake. NOTE
•After a short period, the vehicle is secured
by the electric parking brake, thus relieving
the service brake.
•Depending on the specified minimum dis-
tance, your vehicle will come to a standstill
at a sufficient distance behind the vehicle
in front. The specified minimum distance is
set using the control on the cruise control
lever.
The electric parking brake secures the vehicle
automatically if the ICC system is activated
when the vehicle is stationary and:
•A system fault occurs.
•The power supply is insufficient.
If a malfunction in the electric parking brake
occurs, then the transmission may also be
shifted into position P (Park) automatically.
Starting and driving5-55

1Detected parking space on the left.
2Parking symbol.
3Detected parking space on the right.
IPA is activated automatically when driving
forwards. The system is operational at
speeds of up to approximately 19 MPH (30
km/h). While in operation, the system inde-
pendently locates and measures parking
spaces on both sides of the vehicle
IPA will only detect parking spaces:
•Adjacent to the vehicle.
•Parallel or at right angles to the direction
of travel.
•That are parallel to the direction of travel
and are at least 5 ft (1.5 m) wide.
•That are parallel to the direction of travel
and at least 3.3 ft (1.0 m) longer than your
vehicle.
•That are at right angles to the direction of
travel and at least 3.3 ft (1.0 m) wider than
your vehicle.
NOTE
IPA cannot measure the length of a parking
space if it is at right angles to the direction of
travel. You will need to judge whether your
vehicle will fit in the parking space
When driving at speeds below 19 MPH (30
km/h) you will see parking symbol
2as a
status indicator in the vehicle information
display. When a parking space has been de-
tected, an arrow towards the right
3or the
left
1also appears. IPA only displays park-
ing spaces on the front-passenger side as
standard. Parking spaces on the driver's side
are displayed as soon as the turn signal on the
driver's side is activated. When parking on the
driver's side, this must remain activated until
you confirm the use of IPA by pressing the
<OK> button on the steering wheel. The sys-
tem automatically determines whether the
parking space is parallel or at right angles to
the direction of travel.
A parking space is displayed while you are
driving past it, and until you are approxi-
mately 50 ft (15 m) away from it.
PARKING
NOTE
When the sonar function detects obstacles,
you are responsible for braking in good time.
1. Stop the vehicle when the parking symbol shows the desired parking space in the
combination meter
2. Shift into position R. The [Start Park Assist? Yes: OK No:]
message appears in the vehicle informa-
tion display.
3. To cancel the procedure: press the
button on the steering wheel or pull away
or
4. To park using IPA press the <OK>button
on the steering wheel. The Park Assist
[Observe surroundings] message appears
in the vehicle information display.
5. Release the steering wheel.
6. Back up the vehicle, being ready to brake at all times. When backing up, drive at a
speed below 5 MPH (10 km/h). Other-
wise, IPA will be canceled.
NSD696
Upper display
Starting and driving5-73

•The border of the parking space must not
be too wide, as the position of the vehicle
must not exceed an angle of 45 degrees to
the starting position as it is manoeuvred
into the parking space.
•A total front and back maneuvering dis-
tance of at least 1.0 m must be available.
IPA can only assist you with exiting a parking
space if you have parked the vehicle parallel
to the direction of travel using IPA.
WARNING
•IPA is only an aid. It is not a substitute
for your attention to the immediate sur-
roundings. The responsibility for safe
maneuvering and parking remains with
you.
•Make sure that no persons, animals or
objects are in the maneuvering range.
•When the sonar function is deactivated,
IPA is also unavailable.
•While parking or pulling out of a parking
space, the vehicle swings out and can
drive onto areas of the oncoming lane.
This could cause you to collide with
other road users. There is a risk of an
accident.
•Pay attention to other road users. Stop
the vehicle if necessary or cancel the IPA
parking procedure.
1. Start the engine.
2. Release the electric parking brake.
3. Switch on the turn signal in the direction you are pulling away.
4. Vehicles with automatic transmission:
shift the transmission to position D or R
The [Start Park Assist? Yes: OK No:]
message appears in the vehicle informa-
tion display.
5. To cancel the procedure: press the
button on the steering wheel or pull away
or
6. To exit a parking space using IPA: press the <OK> button on the steering wheel
The Park Assist [Observe surroundings]
message appears in the display.
7. Release the steering wheel.
8. Pull away, being ready to brake at all times Do not exceed a maximum speed of
approximately 5 MPH (10 km/h) when
exiting a parking space. Otherwise, IPA
will be canceled.
WARNING
While parking or pulling out of a parking
space, the vehicle swings out and can drive
onto areas of the oncoming lane. This could
cause you to collide with other road users.
There is a risk of an accident.
9. Depending on the message or as required, shift the transmission to position D or R.
IPA immediately steers in the other direc-
tion. The [Observe surroundings] mes-
sage appears in the display.
NOTE
You will achieve the best results by wait-
ing for the steering procedure to com-
plete before pulling away.
If you back up after activation, the steer-
ing wheel is moved to the straight-ahead
position.
10. Drive forward and back up as prompted by the IPA and sonar function warning
displays, several times if necessary.
Once you have exited the parking space com-
pletely, the steering wheel is moved to the
straight-ahead position. You hear a tone and
the [Park Assist switched off] message ap-
pears in the display. You will then have to
steer and merge into traffic on your own. The
Starting and driving5-75

ARearView/Around View monitor display
BINFINITI controller
C<MENU> button
D<CAMERA> buttonWhen the corner of the vehicle moves closer
to an object, the corner sensor indicators
1appear (if equipped).
When the center of the vehicle moves close
to an object, the center indicator
2appears.When the object is detected, the indicator
(green) appears and blinks and the tone
sounds intermittently. When the vehicle
moves closer to the object, the color of the
indicator turns yellow and the rate of the
blinking increases. When the vehicle is very
close to the object, the indicator stops blink-
ing and turns red, and the tone sounds con-
tinuously.
The sonar function is activated automatically
when you:
•Switch on the ignition
•Shift to position D (Drive), or R (Reverse)
on vehicles with automatic transmission
•Release the electric parking brake
The sonar function is deactivated at speeds
above 10 MPH (16 km/h). It is reactivated at
lower speeds.
NSD707
With RearView monitor
NAA1547
Starting and driving5-81

function and the low tire pressure warn-
ing light will flash for approximately 1
minute. The light will remain on after 1
minute. It is recommended you Contact
an INFINITI retailer as soon as possible
for tire replacement and/or system re-
setting.
•Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
•If you used Emergency Tire Sealant to
repair a minor tire puncture, the TPMS
sensor should be checked when repair-
ing or replacing the tire. It is recom-
mended you visit an INFINITI retailer for
this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the
low tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) ap-
pears in the vehicle information display, one
or more of your tires is significantly under-
inflated. If the vehicle is being driven with low
tire pressure, the TPMS will activate and
warn you of it by the low tire pressure warn-
ing light (in the meter panel). This system will
activate only when the vehicle is driven at
speeds above 16 MPH (25 km/h). For more details about the TPMS, see &#34;Tire
Pressure Monitoring System (TPMS)&#34; in the
&#34;5. Starting and driving&#34; section.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake
firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is
on a slope, ice or slippery area. This is
hazardous.
•Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.
6. Turn off the engine. 7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle and stand in a safe place, away from
other traffic and clear of the vehicle.
In case of emergency6-3

Removing the wheel
WARNING
•The jack must be placed on firm level
ground. Failure to observe this instruc-
tion could result in vehicle damage, or
serious injury or death.
•Make sure to read the caution label at-
tached to the jack body before use.
•DO NOT GET UNDER A VEHICLE THAT
IS SUPPORTED BY A JACK.
•Never use a jack which was not designed
for your vehicle.
•Use the correct jacking points. Never
use any other part of the vehicle for jack
support.
•Never lift the vehicle more than neces-
sary.
•Never use blocks on or under the jack.
•Do not start or run the engine while the
vehicle is on the jack. The vehicle may
move suddenly, and this may cause an
accident.
•Never allow passengers to stay in the
vehicle while the tire is off the ground.
•Remove all loads before lifting the ve-
hicle with the jack.
NOTE
A jack and rod are not provided as standard
equipment with your vehicle. These parts are
dealer options. It is recommended that you
contact an INFINITI retailer for more infor-
mation about obtaining these parts. 1.
Vehicles without intelligent key: Remove
the key from the ignition lock.
Vehicles with a push button ignition
switch: remove the start/stop button
from the ignition lock (see &#34; Push-button
ignition switch (if equipped)&#34; in the &#34;5.
Starting and driving&#34; section).
2. Place the jack directly under the jack-up point as illustrated so that the top of the
jack contacts the vehicle at the jack-up
point.
The jack must be placed on firm level
ground.
NCE453NCE447
Jack-up points
6-6In case of emergency

WARNING
•Do not continue to drive if your vehicle
overheats. Doing so could cause engine
damage or a vehicle fire.
•To avoid the danger of being scalded,
never remove the radiator or coolant
reservoir cap while the engine is hot.
When the radiator or coolant reservoir
cap is removed, pressurized hot water
will spurt out, possibly causing serious
injury.
•Do not open the hood if steam is coming
out.
If the engine of your vehicle is overheating
(indicated by the engine coolant temperature
gauge) or if you feel a lack of engine power,
detect unusual noise, etc., proceed as fol-
lows:
1. Move and park the vehicle safely off the road and away from traffic.
2. Turn on the hazard warning flasher lights.
3. Apply the parking brake.
4. Press the P (Park) button. DO NOT STOP THE ENGINE.
5. Open all windows. 6. Switch off the air conditioner system (if
equipped).
7. Set the heater or air conditioner tempera- ture control to maximum “HOT” and fan
speed control to maximum speed.
8. Exit the vehicle.
9. Visually inspect and listen for steam or coolant escaping from the radiator before
opening the hood.
WARNING
If steam or water is coming from the en-
gine, stand clear to prevent getting
burned.
10. Open the hood. For details, see &#34;Hood&#34; in the &#34;3. Pre-driving checks and adjust-
ments&#34; section.
11. Visually check if the cooling fan is run- ning.
12. Visually check the radiator and radiator hoses for leakage.
WARNING
Be careful not to allow your hands, hair,
jewelry or clothing to come into contact
with, or get caught in, engine belts or the
engine cooling fan. The engine cooling fan
can start at any time.
13. After the engine cools down, check the coolant level in the engine coolant reser-
voir with the engine running. Do not
open the radiator cap (if equipped).
14. If the level is low, remove the engine coolant reservoir cap and add coolant
slowly into the reservoir. After refilling
the reservoir to the MAX level, install the
reservoir cap.
15. Close the hood.
Have your vehicle inspected or repaired. It is
recommended you visit an INFINITI retailer.
IF YOUR VEHICLE OVERHEATS
In case of emergency6-13

Two-Wheel Drive (FWD) models
CAUTION
NEVER tow automatic transmission (DCT)
models with the front wheels on the
ground or with all four wheels on the
ground (forwards or backwards), as this
may cause serious and expensive damage
to the transmission. If it is necessary to tow
the vehicle with the rear wheels raised, al-
ways use towing dollies under the front
wheels.
Four-Wheel Drive (4WD) models
INFINITI recommends that towing dollies be
used under the front or rear wheels when
towing your vehicle or the vehicle be placed
on a flatbed tow truck as illustrated.
CAUTION
Never tow 4WD models with any of the
wheels on the ground. Doing so will cause
serious and expensive damage to the
drivetrain.
Vehicle recovery (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal
injury or death when recovering a stuck ve-
hicle:
•Contact a professional towing service to
recover the vehicle if you have any ques-
tions regarding the recovery procedure.
•Tow chains or cables must be attached
only to main structural members of the
vehicle.
•Do not use the vehicle tie downs to tow
or free a stuck vehicle.
•Only use devices specifically designed
for vehicle recovery and follow the
manufacturer&#39;s instructions.
•Always pull the recovery device straight
out from the front of the vehicle. Never
pull at an angle.
•Route recovery devices so they do not
touch any part of the vehicle except the
attachment point.
•On vehicles with a push button ignition
switch: you must remove the start/stop
NCE450
4WD models
In case of emergency6-15