ECO mode INFINITI QX30 2019 User Guide

Vehicle
Message Possible causes/consequences and solutions
[Depress Brake to Start
Engine](DCT models only). You have attempted to start the engine with the transmission in position N (Neutral) without depressing the
brake pedal.
Depress the brake pedal.
[To Deselect P or N,
Depress Brake and Start
Engine]You have attempted to shift the shift lever to position R (Reverse) or D (Drive) without starting the engine.
Start the engine and depress the brake pedal.
NOTE•It is only possible to move the shift lever from position P (Park) to the desired position if you depress the brake pedal. Only then
can the parking lock be deactivated.
•At transmission fluid temperatures below -5°F (-20°C) you can only shift out of position P (Park) into another transmission
position when the engine is running.
[Apply Brake to Shift
From 'P']You have attempted to shift the shift lever to position R (Reverse), N (Neutral) or D (Drive) without depressing the brake pedal.
Depress the brake pedal.
[Risk of Rolling Transmis-
sion Not in P]The driver's door is open/not fully closed and the shift lever is in position R (Reverse), N (Neutral) or D (Drive).
A warning tone also sounds
WARNING
The vehicle may roll away.
There is a risk of an accident.
1. Press the P (Park) button.
2. Secure the vehicle against rolling away.
3. Close the driver's door fully.
[Service Required Do Not
Shift Gears Visit Dealer]You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D (Drive) is selected, Drive to an INFINITI retailer without shifting the transmission from position D (Drive).
If transmission position R (Reverse), N (Neutral) or P (Park), secure the vehicle against rolling away. It is recommended you consult
an INFINITI retailer.
2-54Instruments and controls

Key
Problem Possible causes/consequences and solutions
[Key Does Not Belong to
Vehicle]You have put the wrong key in the ignition switch.
Use the correct key.
[Obtain a New Key]The key needs to be replaced.
It is recommended you visit an INFINITI retailer for this service.
[Replace Key Battery]The key battery is discharged.
Replace the battery (see "Checking the battery")
[Key Not Detected] (red
display message)The key is not in the vehicle.
A warning tone also sounds.
If the engine is switched off, you can no longer lock the vehicle centrally or start the engine.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Locate the key.
Because there is interference from a strong source of radio waves, the key is not detected whilst the engine is running.
A warning tone also sounds.
If the engine is switched off, you can no longer lock the vehicle centrally or start the engine.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Insert the key into the ignition lock and bring into key mode.
2-58Instruments and controls

NOTE
The “Windshield demisting” function auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the air-
flow may increase or decrease automatically
after the
button is pressed
NOTE
You can adjust the blower output manually
while the “Windshield demisting” function is
in operation: by adjusting the airflow control
for the air-conditioning or climate control
system (see "Heater and air conditioner").
To deactivate the de-icer:
•Press thebutton. The indicator light
in thebutton turns off. The previous
settings are reactivated. Air-recirculation
mode remains deactivated.
or
•Automatic climate control: press the
<AUTO>button. The indicator light in the
button turns off. Airflow and air dis-
tribution are set to automatic mode.
or
•Air-conditioning system or automatic cli-
mate control: adjust the temperature con-
trol (see &#34;Heater and air conditioner&#34;).
HEADLIGHT SWITCH
1Left-hand parking lights
2Right-hand parking lights
3Side lights and license plate lighting
4<AUTO>Automatic headlight mode,
controlled by the light sensor
5Low beam/high beam headlights
6Rear fog light
7Front fog lights (if equipped)
8Headlight aiming control (halogen head-
lights only)
INFINITI recommends that you consult the
local regulations concerning the use of lights.
If
you hear a warning tone when you leave the
vehicle, the side lights may still be switched on.
Turn the light switch to<AUTO>.
The exterior lighting (except the side lights/
parking lights) switches off automatically if you:
•Remove the key from the ignition switch
(if equipped).
•Open the driver&#39;s door with the ignition
switch in the OFF position.
CAUTION
Use the headlights with the engine running
to avoid discharging the vehicle battery.
NIC2619
LED headlights
NIC2697
Halogen headlights
HEADLIGHT AND TURN SIGNAL
SWITCHES
Instruments and controls2-65

Active light function
The active light function is a system that
moves the headlights according to the steer-
ing movements of the front wheels. In this
way relevant areas remain illuminated while
you are driving. This helps you to recognize
pedestrians, cyclists and animals. It is active
when the lights are switched on.
Cornering light function
The cornering light function improves the il-
lumination of the road over a wide angle in
the direction you are turning, enabling better
visibility in tight bends, for example. It can
only be activated when the low-beam head-
lights are switched on. It is active if you are
driving at speeds below 25 MPH (40 km/h)
and switch on the turn signal or turn the
steering wheel.
The cornering light function may remain lit for
a short time, but is automatically switched off
after no longer than three minutes.
Freeway mode
Freeway mode adjusts the light beam to re-
duce the amount of light that shines on the
opposite lane of the freeway, and oncoming
traffic.
Freeway mode is active if you are driving at a
speed above 68 MPH (110 km/h) and do not
make any large steering movements for at
least 3300 ft (1000 m) or if you are driving at
a speed above 81 MPH (130 km/h).
It is not active if you are driving at speeds
below 50 MPH (80 km/h) following activa-
tion.
NSD593NSD592NSD594
2-68Instruments and controls

WARNING
•Do not use the HomeLink® Universal
Transceiver with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards. (These standards be-
came effective for opener models manu-
factured after April 1, 1982). A garage
door opener which cannot detect an ob-
ject in the path of a closing garage door
and then automatically stop and re-
verse, does not meet current federal
safety standards. Using a garage door
opener without these features increases
the risk of serious injury or death.
•During the programming procedure
your garage door or security gate will
open and close (if the transmitter is
within range). Make sure that people or
objects are clear of the garage door,
gate, etc. that you are programming.
•Your vehicle’s engine should be turned
off while programming the HomeLink®
Universal Transceiver.NOTE
Certain garage door drives are incompatible
with the integrated garage door opener.
If you have difficulty programing the inte-
grated garage door opener, it is recom-
mended you contact your INFINITI retailer.
PROGRAMMING HOMELINK®
If you have any questions or are having diffi-
culty programming your HomeLink® but-
tons, refer to the HomeLink® web site at:
www.homelink.com or call 1-800-355-3515.1. Turn the ignition key to the ON position.
2. Press and hold one of buttons
2to4on
the HomeLink®.
HomeLink® is now in programing mode.
After a short time, indicator light
1lights
up yellow.
Indicator light
1lights up yellow as soon
as button
2,3or4is programed for
the first time. If the selected button has
already been programed, indicator light
1will only light up yellow after ten sec-
onds have elapsed.
3. Release button
2,3or4. Indicator
light
1flashes yellow.
4. Position the end of your hand-held trans-
mitter
52–8 inches (5–20 cm) away
from the HomeLink® surface, keeping the
HomeLink® indicator light
1in view.
NDI1631
2-90Instruments and controls

The bird&#39;s-eye view shows the overhead view
of the vehicle, which helps confirm the vehicle
position.
The vehicle icon
1shows the position of the
vehicle.
NOTE
The size of the vehicle icon on the bird&#39;s-eye
view may differ somewhat from the actual
vehicle.
The areas that the cameras cannot cover
2are indicated in black.
The non-viewable area
2is highlighted in
yellow for several seconds after the bird&#39;s-
eye view is displayed. It will be shown only the
first time after the ignition switch is placed in
the ON position.
When the corner of the vehicle moves closer
to an object, the corner sensor indicator
3appears.Front-side view:
Guiding lines that indicate the approximate
width and the front end of the vehicle are
displayed on the monitor.
The front-of-vehicle line
1shows the front
part of the vehicle.
The side-of-vehicle line
2shows the ap-
proximate vehicle width including the outside
mirrors.
The extensions
3of both the front1and
side
2lines are shown with a green dotted
line.
The corner sensor indicator
4will appear
when a corner of the vehicle moves closer to
an object.
DIFFERENCE BETWEEN
PREDICTED AND ACTUAL
DISTANCES
The displayed guidelines and their locations
on the ground are for approximate reference
only. Objects on uphill or downhill surfaces or
projecting objects will be actually located at
distances different from those displayed in
the monitor relative to the guidelines (refer to
illustrations). When in doubt, turn around and
view the objects as you are backing up, or
park and exit the vehicle to view the position-
ing of objects behind the vehicle.
NAA1681SAA1842Z
Left-Hand Drive (LHD) models*
Display screen, heater and air conditioner, and audio system4-15

WARNING
•The heater and air conditioner operate
only when the engine is running.
•Never leave children or adults who
would normally require the support of
others alone in the vehicle. Pets should
not be left alone either. They could un-
knowingly activate switches or controls
and inadvertently become involved in a
serious accident and injure themselves.
On hot, sunny days, temperatures in a
closed vehicle could quickly become high
enough to cause severe or possibly fatal
injuries to people or animals.
•Do not use the recirculation mode for
long periods as it may cause the interior
air to become stale and the windows to
fog up.
•Do not adjust the heating and air condi-
tioning controls while driving so that
full attention may be given to vehicle
operation.
The heater and air conditioner operate when
the engine is running. The air blower will op-
erate even if the engine is turned off and the
ignition switch is in the ON position.NOTE
•Condensation forms inside the air condi-
tioning unit when the air conditioner (if
equipped) is running, and is safely dis-
charged underneath your vehicle.
Traces of water on the ground are there-
fore normal.
•Odors from inside and outside the vehicle
can build up in the air conditioner unit.
Odor can enter the passenger compart-
ment through the ventilators.
When parking, set the heater and air con-
ditioner controls to turn off air recircula-
tion to allow fresh air into the passenger
compartment. This should help reduce
odors inside the vehicle.
Observe the settings recommended on the
following pages. The windows could other-
wise mist up. To prevent the windows from
misting up
•Switch off climate control only briefly.
•Switch on air-recirculation mode only
briefly.
•Switch on the cooling with air dehumidifi-
cation function.
•Switch on the windshield demisting func-
tion briefly, if required.The air-conditioning system/automatic cli-
mate control regulates the temperature and
the humidity of the vehicle interior and filters
undesirable substances from the air.
The air-conditioning system/automatic cli-
mate control can only be operated when the
engine is running. Optimum operation is only
achieved with the side windows closed.
Always keep the ventilation flaps behind the
side panelling clear. Otherwise the vehicle will
not be ventilated correctly.
NOTE
•Ventilate the vehicle for a brief period
during warm weather. This will speed up
the cooling process and the desired inte-
rior temperature will be reached more
quickly.
•The integrated filter filters out most par-
ticles of dust and soot and completely fil-
ters out pollen. With automatic climate
control, gaseous pollutants and odors will
also be reduced. A clogged filter reduces
the amount of air supplied to the vehicle
interior. For this reason, you should al-
ways observe the interval for replacing
the filter, which is specified in the Service
Booklet. As this depends on environmen-
tal conditions, for example heavy air pol-
lution, the interval may be shorter than
stated in the Service Booklet.
HEATER AND AIR CONDITIONER
Display screen, heater and air conditioner, and audio system4-29

AIR CONDITIONING SYSTEM
1Sets the temperature
2De-ices/defogs the windshield
3Set the air distribution
4Activates/deactivates air-recirculation
mode
5Sets the airflow
6Activates/deactivates cooling with air
dehumidification
7Switches the rear window defroster on/
off
Operating tips
A number of tips and recommendations for
optimum use of the air-conditioning system
are listed below:
•Switch on the air-conditioning system by
turning control knob
5clockwise to the
desired position (except position0)
•Set the temperature to 70° F (22° C)
•Recommendation for avoiding misted
windows at low exterior temperatures or
in rain: switch on the
cooling with
dehumidification function. Set air distri-
bution to
and if possible switch
offand. Deactivate air-
recirculation mode.
Set airflow control
5to a setting be-
tween 3 and 6.
•Recommendation for rapid cooling or
heating of the vehicle interior: briefly set
airflow control
5to a setting between 3
and 6.
•Recommendation for a constant vehicle
interior temperature: set airflow control
5to a setting between 1 and 3.
NAA1644
4-30Display screen, heater and air conditioner, and audio system

•Recommendation for air distribution in
winter: select theandsettings.
Recommendation for air distribution in
summer: select the
orandsettings.
•Only use the &#34;Windshield demisting&#34; func-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-
clockwise to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the &#34;Cooling with air dehu-
midification&#34; function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the &#34;Cooling with air
dehumidification&#34; function briefly.
The &#34;Cooling with air dehumidification&#34; func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.
To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.Problems with the &#34;Cooling with air dehu-
midification&#34; function:
Problem:The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution:The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70° F (22° C).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Display screen, heater and air conditioner, and audio system4-31

AUTOMATIC CLIMATE
CONTROL (2–ZONE)
1Sets the temperature, left
2Sets climate control to automatic mode
3Demists the windshield
4Increases the airflow
5Sets the air distribution
6Display
7Activates/deactivates air-recirculation
mode
8Switches climate control on/off
9Sets the temperature, right
10Activates/deactivates the Max Cool
function
11Activates/deactivates cooling with air
dehumidification
12Reduces the airflow
13Switches the rear window heating on/
off
14Switches the ZONE function on/off
Operating tips
A number of tips and recommendations to
enable you to get the most out of your auto-
matic climate control are listed below:
•Activate climate control using theandbuttons. The indicator lights in
theandbuttons light up.
•Set the temperature to 70° F (22° C)
•Only use the &#34;Windshield demisting&#34; func-
tion briefly until the windshield is clear
again.
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•Use thefunction to adopt the tem-
perature settings on the driver&#39;s side for
the front-passenger side as well. The indi-
cator light in the
button goes out.
NAA1705
4-34Display screen, heater and air conditioner, and audio system