brake sensor INFINITI QX30 2019 User Guide

Page 300 of 436

•The system is outside the operating tem-
perature range.
•The on-board voltage is too low.
Once the causes listed above no longer apply,
the display message goes out. The FEB sys-
tem is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as
soon as possible, paying attention to road
and traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
[Emergency Brake Inoperative]:The FEB
system is temporarily inoperative due to a
malfunction. The adaptive brake assist func-
tion may also have failed.
It is recommended you visit an INFINITI re-
tailer.
[Radar Sensors Dirty See Operator's
Manual]:The FEB system is temporarily re-
stricted or inoperative. Possible causes:
•The sensor behind the INFINITI logo is dirty.
•The function of the FEB system is im-
paired due to heavy rain or snow.
A warning tone also sounds.Once the causes listed above no longer apply,
the display message goes out. The FEB sys-
tem is operative again.
If the display message does not disappear:
•Pull over and stop the vehicle safely as
soon as possible, paying attention to road
and traffic conditions.
•Secure the vehicle against rolling away.
•Switch off the engine.
•Clean the area around the sensors.
•Restart the engine. The display message
disappears.
SYSTEM MAINTENANCE
The sensorAis located behind the INFINITI
logo at the front of the vehicle.
To keep the system operating properly, be
sure to observe the following:
•Always keep the sensor area of the
INFINITI logo clean.
•Do not strike or damage the areas around
the sensor.
•Do not cover or attach stickers or similar
objects on the front bumper near the sen-
sor area. This could cause failure or mal-
function.
•Do not attach metallic objects near the
sensor area (brush guard, etc.). This could
cause failure or malfunction.
•Do not alter, remove or paint the front
grille or INFINITI logo.
NSD645
5-68Starting and driving

Page 302 of 436

ACTIVE SOUND ENHANCEMENT
The active sound enhancement generates
sounds according to engine speed through
the speakers
2and woofer1(if equipped)
to enhance the quality of the engine sound.IPA is an electronic parking aid with ultra-
sound. It detects vehicles and open spaces on
both sides of the vehicle. A parking symbol
indicates a suitable parking space. Active
steering intervention can assist you during
parking and when exiting a parking space.
The driver controls the accelerator, brake and
gear shift. You may also use the Camera Aid-
ing Sonar (parking sensor) function (see "
Camera Aiding Sonar (parking sensor) func-
tion (if equipped)" later in this section).
IMPORTANT SAFETY NOTES
WARNING
•IPA is only an aid. It is not a substitute
for your attention to the immediate sur-
roundings. The responsibility for safe
maneuvering and parking remains with
you.
•Make sure that no persons, animals or
objects are in the maneuvering range
•When the sonar (parking sensor) func-
tion is deactivated, IPA is also unavail-
able.
•While parking or pulling out of a parking
space, the vehicle swings out and can
drive onto areas of the oncoming lane.
This could cause you to collide with
other road users. There is a risk of an
accident.
•Pay attention to other road users. Stop
the vehicle if necessary or cancel the IPA
parking procedure
•This system is not designed to prevent
contact with small or moving objects.
•If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or
bent, the sensing zone may be altered
causing inaccurate measurement of ob-
stacles or false alarms.
•This system is not designed to prevent
contact with small or moving objects.
•If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or
bent, the sensing zone may be altered
causing inaccurate measurement of ob-
stacles or false alarms.
INTELLIGENT PARKING ASSIST (IPA)
(IF EQUIPPED)
5-70Starting and driving

Page 312 of 436

ARearView/Around View monitor display
BINFINITI controller
C<MENU> button
D<CAMERA> buttonWhen the corner of the vehicle moves closer
to an object, the corner sensor indicators
1appear (if equipped).
When the center of the vehicle moves close
to an object, the center indicator
2appears.When the object is detected, the indicator
(green) appears and blinks and the tone
sounds intermittently. When the vehicle
moves closer to the object, the color of the
indicator turns yellow and the rate of the
blinking increases. When the vehicle is very
close to the object, the indicator stops blink-
ing and turns red, and the tone sounds con-
tinuously.
The sonar function is activated automatically
when you:
•Switch on the ignition
•Shift to position D (Drive), or R (Reverse)
on vehicles with automatic transmission
•Release the electric parking brake
The sonar function is deactivated at speeds
above 10 MPH (16 km/h). It is reactivated at
lower speeds.
NSD707
With RearView monitor
NAA1547
5-80Starting and driving

Page 316 of 436

SYSTEM MAINTENANCE
CAUTION
Keep the surface of the sonar sensors (if
equipped) (located on the front and rear
bumper fascia) free from accumulations of
snow, ice and dirt. Do not scratch the sur-
face of the sonar sensors when cleaning. If
the sensors are covered, the accuracy of
the sonar function will be diminished.During the first 1,200 miles (2,000 km), fol-
low these recommendations to obtain maxi-
mum engine performance and ensure the fu-
ture reliability and economy of your new
vehicle. Failure to follow these recommenda-
tions may result in shortened engine life and
reduced engine performance.
•Avoid driving for long periods at constant
speed, either fast or slow, and do not run
the engine over 4,000 RPM.
•Do not accelerate at full throttle in any
gear.
•Avoid quick starts.
•Avoid hard braking as much as possible.
•Do not tow a trailer for the first 500 mi
(805 km). Your engine, axle or other parts
could be damaged.
You should also observe these notes on
break-in if the engine or parts of the drive
train on your vehicle have been replaced.
CAUTION
In certain driving and driving safety sys-
tems, the sensors adjust automatically
while a certain distance is being driven af-
ter the vehicle has been delivered or after
repairs. Full system effectiveness is not
reached until the end of this teach-in pro-
cess.
Brake pads/linings and rotors that are ei-
ther new or have been replaced only
achieve optimum braking effect after sev-
eral hundred miles of driving. Compensate
for the reduced braking effect by applying
greater force to the brake pedal
BREAK-IN SCHEDULE
5-84Starting and driving

Page 324 of 436

Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic fea-
ture that tests the system each time you start
the engine and move the vehicle at a low
speed in forward or reverse. When the self-
test occurs, you may hear a “clunk” noise
and/or feel a pulsation in the brake pedal.
This is normal and does not indicate a mal-
function. If the computer senses a malfunc-
tion, it switches the ABS off and illuminates
the ABS warning light on the instrument
panel. The brake system then operates nor-
mally, but without anti-lock assistance. If the
ABS warning light illuminates during the
self-test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6
MPH (5 to 10 km/h). The speed varies ac-
cording to road conditions.
When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic pres-
sure. This action is similar to pumping the
brakes very quickly. You may feel a pulsation
in the brake pedal and hear a noise from
under the hood or feel a vibration from the
actuator when it is operating. This is normal
and indicates that the ABS is operating prop-
erly. However, the pulsation may indicate
that road conditions are hazardous and extra
care is required while driving.The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver inputs
and vehicle motion. Under certain driving
conditions, the VDC system helps to perform
the following functions.
•Controls brake pressure to reduce wheel
slip on one slipping drive wheel so power is
transferred to a non slipping drive wheel
on the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle in the
following conditions:
– understeer (vehicle tends to not follow
the steered path despite increased
steering input)
– oversteer (vehicle tends to spin due to
certain road or driving conditions).
The VDC system can help the driver to main-
tain control of the vehicle, but it cannot pre-
vent loss of vehicle control in all driving situ-
ations.
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
5-92Starting and driving

Page 333 of 436

•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not
function and the low tire pressure warn-
ing light will flash for approximately
1 minute. The light will remain on after
1 minute. It is recommended you Con-
tact an INFINITI retailer as soon as pos-
sible for tire replacement and/or system
resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
•If you used Emergency Tire Sealant to
repair a minor tire puncture, the TPMS
sensor should be checked when repair-
ing or replacing the tire. It is recom-
mended you visit an INFINITI retailer for
this service.
The Tire Pressure Monitoring System (TPMS)
monitors tire pressure of all tires. When the
low tire pressure warning light is lit, and a tire
pressure-related warning (if equipped) ap-
pears in the vehicle information display, one
or more of your tires is significantly under-
inflated. If the vehicle is being driven with low
tire pressure, the TPMS will activate and
warn you of it by the low tire pressure warn-
ing light (in the meter panel). This system willactivate only when the vehicle is driven at
speeds above 16 MPH (25 km/h).
For more details about the TPMS, see &#34;Tire
Pressure Monitoring System (TPMS)&#34;.
STOPPING VEHICLE
WARNING
•Be sure to apply the parking brake
firmly.
•Be sure that P (Park) is engaged.
•Never change tires when the vehicle is
on a slope, ice or slippery area. This is
hazardous.
•Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away
from traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Press the P (Park) button.
6. Turn off the engine.7. Open the hood and set up the triangle
reflector (if equipped):
•To warn other traffic.
•To signal professional road assistance
personnel that you need assistance.
8. Have all passengers get out of the vehicle
and stand in a safe place, away from
other traffic and clear of the vehicle.
In case of emergency6-3

Page 389 of 436

adversely affect the ride, braking, han-
dling, VDC system, ground clearance,
body-to-tire clearance, tire chain clear-
ance, speedometer calibration, head-
light aim and bumper height. Some of
these effects may lead to accidents and
could result in serious personal injury.
•For 2WD models, if your vehicle was
originally equipped with 4 tires that
were the same size and you are only re-
placing 2 of the 4 tires, install the new
tires on the rear axle. Placing new tires
on the front axle may cause loss of ve-
hicle control in some driving conditions
and cause an accident and personal in-
jury.
•If the wheels are changed for any rea-
son, always replace with wheels which
have the same offset dimension. Wheels
of a different offset could cause prema-
ture tire wear, degrade vehicle handling
characteristics, affect the VDC system
and/or interference with the brake
discs. Such interference can lead to de-
creased braking efficiency and/or early
brake pad wear. For additional informa-
tion on wheel offset dimensions, refer to
&#34;Wheels and Tires&#34;.
•When a replacement tire is mounted or a
wheel is replaced, the TPMS will not
function and the low tire pressure warn-
ing light will flash for approximately 1
minute. The light will remain on after 1
minute. Contact an INFINITI retailer as
soon as possible for tire replacement
and/or system resetting.
•Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
•The TPMS sensor may be damaged if it
is not handled correctly. Be careful when
handling the TPMS sensor.
•When replacing the TPMS sensor, the ID
registration may be required. It is rec-
ommended that you visit an INFINITI re-
tailer for ID registration.
•Do not use a valve stem cap that is not
specified by INFINITI. The valve stem
cap may become stuck.
•Be sure that the valve stem caps are cor-
rectly fitted. Otherwise the valve may
be clogged up with dirt and cause a mal-
function or loss of pressure.
•Do not install a damaged or deformed
wheel or tire even if it has been repaired.
Such wheels or tires could have struc-
tural damage and could fail without
warning.
•The use of retread tires is not recom-
mended.
•For additional information regarding
tires, refer to &#34;Important Tire Safety
Information&#34; (US) or &#34;Tire Safety Infor-
mation&#34; (Canada) in the Warranty In-
formation Booklet.
Care of wheels
•Wash the wheels when washing the ve-
hicle to maintain their appearance.
•Clean the inner side of the wheels when
the wheel is changed or the underside of
the vehicle is washed.
•Do not use abrasive cleaners when wash-
ing the wheels.
•Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss of
pressure or poor seal at the tire bead.
•INFINITI recommends waxing the road
wheels to protect against road salt in ar-
eas where it is used during winter.
Do-it-yourself8-35

Page 431 of 436

Vanity mirror................3-18
Vanity mirror lights.............2-89
Moving object detection (MOD)......4-24
O
Oil........................10-2
Capacities and recommendations....10-2
Changing engine oil.............8-5
Changing engine oil filter..........8-6
Checking engine oil level..........8-5
Overheating ..................6-13
Engine....................6-13
Engine coolant temperature gauge....2-6
Overview.....................0-6
Cockpit .................0-6,2-2
Engine compartment.........0-9,8-3
Exterior....................0-3
Interior.....................0-5
Seats, Seat belts, Supplemental restraint
system.....................0-2
P
Parcelshelf...................2-85
Installation..................2-86
Removal...................2-85
Parking.....................5-87
Brake.....................5-27
Parking sensor system...........5-76Sonar function...............5-76
Parkingsensors ................5-81
OFF switch.................5-81
Phone......................4-39
Power.......................3-6
Door lock switch...............3-6
Outlet ....................2-79
Seat adjustment...............1-4
Steering...................5-89
Windows..................2-74
Precautions...................1-34
Boosterseats................1-34
Brake.....................5-90
Child restraints...............1-19
Intelligent Parking Assist (IPA)......5-70
Maintenance.................8-2
Safety.....................4-2
Seat belt usage...............1-10
Starting and driving.............5-2
Supplemental Restraint System.....1-37
Tire Pressure Monitoring System
(TPMS)....................5-3
Pregnant women................1-12
Protection ....................7-7
Corrosion...................7-7
Push-button ignition.............5-14
Push-starting..................6-12
R
Rear seats....................1-5
Folding.....................1-6
RearView monitor................4-3
Maintenance................4-11
Repairing....................8-25
Headlights..................8-25
Replacement..................1-54
Airbags ...................1-54
Air cleaner filter...............8-13
Engine coolant................8-4
Engine oil...................8-5
Engine oil filter................8-6
Intelligent Key battery...........8-20
Spark plugs.................8-12
Tires and wheels..............8-34
Wiper blades................8-13
Roof.......................2-78
Glass.....................2-78
Sunshade operation............2-78
Roof Rack....................2-86
S
Safety......................1-17
Children ...................1-17
Child safety rear door locks........3-7
Head restraints................1-7
Injuredpersons...............1-12
Index11-5

Page 432 of 436

Precautions..................4-2
Pregnant women..............1-12
Reporting safety defects........10-17
Seat belts................1-10,1-13
Adjustment.................1-15
Children-Infants..............1-17
Children-Larger..............1-18
Children - Small...............1-18
Childsafety .................1-17
Cleaning....................7-5
Maintenance................1-16
Overview...................0-2
Precautions.................1-10
Warninglight................2-11
Warnings...................1-13
Seats.......................1-2
Adjustment..................1-4
Adjustment (Manual)............1-3
Booster seats................1-34
Head restraints................1-7
Heating ...................2-73
Leather ....................7-6
Memory...................3-21
Overview...................0-2
Rear......................1-5
Rear seats - Folding.............1-6
Seat belts..................1-10
Security system................2-60
Servicing....................4-38
Air conditioner...............4-38Sonar function.................5-81
OFF switch.................5-81
Spark plugs...................8-12
Information.................8-12
Replacement................8-12
Speedometer...................2-5
Starting.....................5-16
Before starting the engine........5-16
Engine....................5-16
Jump-starting................6-10
Precautions..................5-2
Push-starting................6-12
Steering.....................5-89
Power steering system..........5-89
Steering wheel.................3-17
Adjustment.................3-17
Storage.....................2-80
Luggage hooks...............2-84
Luggage net.................2-85
Mappocket.................2-84
Sunshade....................2-78
Operation..................2-78
Sunvisors....................3-18
Supplemental Restraint System.......1-37
Overview...................0-2
Supplemental Restraint System (SRS)....0-2
Air bags....................0-2
Switches.....................2-71
Brightness..................2-71
Defroster ..................2-64
Foglights ..................2-71Front passenger air bag..........1-45
Hazard warning flasher...........6-2
Headlight..................2-65
Ignition
....................5-13
Ignition positions..............5-13
Parkingbrake................5-27
Parking sensor system...........5-81
Power door lock...............3-6
Push-button ignition............5-14
Seat......................3-21
Seat adjustment...............1-4
Sonar function...............5-81
Turn signal..................2-67
Windshieldde-icer.............2-64
Wiperandwasher.............2-61
T
Tachometer...................2-6
Three-way catalyst...............5-2
Precautions..................5-2
Tire chains...................8-33
Tires.......................8-34
Changing..................8-34
Coldweather................5-96
Equipment..................5-96
Flat tire....................6-2
Inflationpressure..............8-28
Placard...................10-11
Quality grading..............10-16
11-6Index

Page:   < prev 1-10 11-20