Ins INFINITI QX56 2004 Factory Service Manual

A/T SHIFT LOCK SYSTEM
AT-239
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Component InspectionUCS002J A
SHIFT LOCK SOLENOID

Check operation by applying battery voltage to the A/T device.
CAUTION:
Be sure to apply the voltage of the correct polarity to the
respective terminals. Otherwise, the part may be damaged.
DETENTION SWITCH
For key:

Check continuity between terminals of the A/T device.
DETENTION SWITCH
For shift:

Check continuity between terminals of the A/T device.
KEY LOCK SOLENOID
Key lock

Check operation by applying battery voltage to key switch and
key lock solenoid.
CAUTION:
Be careful not to cause burnout of the harness.
Connector No. Terminal No.
M203 9 (Battery voltage) - 10 (Ground)
LCIA0328E
ConditionConnector
No.Terminal No. Continuity
When selector lever is “P”
position.
M203 5 - 6No
When selector lever is not “P”
position.Ye s
LIIA1599E
ConditionConnector
No.Terminal No. Continuity
When selector lever is “P”
position.
M203 3 - 4No
When selector lever is not “P”
position.Ye s
WCIA0401E
Connector No. Terminal No. (Wire color)
M27 1 (Battery voltage) - 2 (Ground)
WCIA0240E

AT-240
A/T SHIFT LOCK SYSTEM
Revision: August 20072004 QX56
Key unlock

Check operation by applying battery voltage to key switch and
key lock solenoid.
CAUTION:
Be careful not to cause burnout of the harness.
KEY SWITCH

Check continuity between terminals of the key switch and key
lock solenoid.
STOP LAMP SWITCH

Check continuity between terminals of the stop lamp switch.
Check stop lamp switch after adjusting brake pedal.
Connector No. Terminal No. (Wire color)
M27 2 (Battery voltage) - 1 (Ground)
WCIA0241E
Condition Connector No.Te r m i n a l N o .
(Wire color)Continuity
Key inserted
M27 3 - 4Ye s
Key withdrawn No
WCIA0242E
ConditionConnector
No.Te r m i n a l N o .
(Wire color)Continuity
When brake pedal is depressed
E38 3 - 4Ye s
When brake pedal is released No
SCIA2126E

AT-242
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Drain ATF through drain plug.
3. Disconnect A/T assembly harness connector.
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
6. Remove oil pan and oil pan gasket.
7. Check foreign materials in oil pan to help determine causes of
malfunction. If the A/T fluid is very dark, smells burned, or con-
tains foreign particles, frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.

If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to AT- 1 5 , "
A/T Fluid Cooler Cleaning" .
SCIA5021E
SCIA5022E
SCIA2308E
SCIA5199E

ON-VEHICLE SERVICE
AT-245
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Installation
CAUTION:
After completing installation, check fluid leakage and fluid level. Refer to AT-13, "
Changing A/T Fluid"
, AT-13, "Checking A/T Fluid" .
1. Install O-ring in A/T assembly harness connector.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
2. Install A/T fluid temperature sensor 2 to bracket.
3. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 mount-
ing bolt to the specified torque. Refer to AT-241, "
COMPO-
NENTS" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
4. Install control valve with TCM in transmission case.
CAUTION:

Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.

Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.

Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
SCIA5155E
SCIA5264E
SCIA5301E
SCIA5034E

AT-246
ON-VEHICLE SERVICE
Revision: August 20072004 QX56

Assemble it so that manual valve cutout is engaged with
manual plate projection.
5. Install bolts A, B and C in control valve with TCM.
6. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1 → 2 → 3), and then tighten other
bolts.
7. Tighten control valve with TCM mounting bolts to the specified
torque. Refer to AT-241, "
COMPONENTS" .
8. Connect A/T fluid temperature sensor 2 connector.
SCIA5142E
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5139E
SCIA5140E
SCIA5023E

ON-VEHICLE SERVICE
AT-247
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
9. Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip.
10. Connect revolution sensor connector.
11. Securely fasten revolution sensor harness with terminal clips.
12. Install magnets in oil pan.
13. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan.
CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old gasket, etc. From oil pan gasket mounting surfaces.
SCIA5146E
SCIA5024E
SCIA3969E
SCIA5200E

AT-248
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old gasket, etc.
From oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse oil pan mounting bolts.
14. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse drain plug gasket.
15. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
16. Install snap ring to A/T assembly harness connector.
17. Connect A/T assembly harness connector.
18. Pour ATF into transmission assembly. Refer to AT - 1 3 , "
Chang-
ing A/T Fluid" .
19. Connect the negative battery terminal
SCIA2308E
SCIA2492E
SCIA5038E
SCIA5039E

ON-VEHICLE SERVICE
AT-249
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Drain ATF through drain plug.
3. Remove oil pan and oil pan gasket.
4. Check foreign materials in oil pan to help determine causes of
malfunction. If the A/T fluid is very dark, smells burned, or con-
tains foreign particles, frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.

If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to AT-15, "
A/T Fluid Cooler Cleaning" .
5. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
6. Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
SCIA2308E
SCIA5199E
SCIA5023E
SCIA5146E

AT-250
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
7. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
8. Remove bracket from A/T fluid temperature sensor 2.
Installation
CAUTION:
After completing installation, check fluid leakage and fluid level. Refer to AT-1 3, "
Changing A/T Fluid"
, AT-1 3, "Checking A/T Fluid" .
1. Install A/T fluid temperature sensor 2 to bracket.
2. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 mount-
ing bolt to the specified torque. Refer to AT-241, "
COMPO-
NENTS" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
SCIA5253E
SCIA5264E
SCIA5264E
SCIA5253E

ON-VEHICLE SERVICE
AT-251
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
3. Connect A/T fluid temperature sensor 2 connector.
4. Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan.
CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old sealant, etc. From oil pan gasket mounting surfaces.
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old sealant, etc.
From oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT- 2 4 1 , "
COMPONENTS" .
CAUTION:
Do not reuse oil pan mounting bolts.
6. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse drain plug gasket.
7. Pour ATF into transmission assembly. Refer to AT-13, "
Chang-
ing A/T Fluid" .
8. Connect the negative battery terminal
SCIA5023E
SCIA5146E
SCIA2308E
SCIA2492E