fluid INFINITI QX56 2004 Factory Service Manual

FAX-10
DRIVE SHAFT
Revision: August 20072004 QX56
Steel Ball

Check for any compression scars, cracks, fractures, or unusual wear.
Inner Race

Check the ball sliding surface for any compression scars, cracks, or fractures.

Check for any damage to the serrated part.
CAUTION:
If any defective conditions are found, install a new housing, ball cage, steel ball, and inner race as
a set.
ASSEMBLY
Final Drive Side
1. Wrap the serrated part of the drive shaft with tape. Install the
boot band and boot to drive shaft.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
2. Remove the tape wound around the serrated part of the drive shaft.
3. Install the ball cage, steel ball, and inner race assembly on the
drive shaft, and secure them tightly using the snap ring.
NOTE:
Discard the old snap ring and use a new one for assembly.
4. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, onto the housing (indicated by * marks), and install it
onto shaft. Refer to MA-10, "
RECOMMENDED FLUIDS AND
LUBRICANTS" .
5. Install the stopper ring onto the housing.
6. After installation, pull on the shaft to check engagement between the sliding joint and the stopper ring.
SFA80 0
SDIA11 25 E
Grease capacity : 130 − 150 g (4.58 − 5.29 oz)
RAC0678D

DRIVE SHAFT
FAX-11
C
E
F
G
H
I
J
K
L
MA
B
FA X
Revision: August 20072004 QX56
7. Install the boot securely into the grooves (indicated by * marks)
as shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
8. Check that the boot installation length “L” is the length indicated
below. Insert a flat-tip screwdriver or similar tool into the big end
of the boot. Bleed air from the boot to prevent boot deformation.
CAUTION:

The boot may break if the boot installation length is less than the specified value.

Do not to touch the tip of the screwdriver to the inside of the boot.
9. Secure the big and small ends of the boot with the new boot
bands as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
10. After installing the sliding joint housing to the drive shaft, rotate the boot to check that the boot is posi-
tioned correctly. If the boot is not positioned correctly, reposition the boot and secure the boot using a new
boot band.
Wheel Side
1. Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to MA-10, "
REC-
OMMENDED FLUIDS AND LUBRICANTS" . After inserting the
grease, use a shop cloth to wipe off the grease that has oozed
out.
2. Wrap the serrated part of the drive shaft with tape. Install the
boot band and boot onto the shaft. Do not damage the boot.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3. Remove the protective tape wound around the serrated part of
the drive shaft.Boot installation length “L ” : 145 mm (5.71 in)
WDIA0287E
SFA39 5
SDIA11 27 E
SFA80 0

FAX-12
DRIVE SHAFT
Revision: August 20072004 QX56
4. Attach the circlip to the drive shaft. The circlip must fit securely
into the drive shaft groove. Attach the nut to the joint sub-assem-
bly.
Use a soft hammer to press-fit the circlip.
NOTE:
Discard the old circlip and use a new one for assembly.
5. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the joint sub-assembly and the large end of the
boot. Refer to MA-10, "
RECOMMENDED FLUIDS AND LUBRI-
CANTS" .
6. Install the boot securely into the grooves (indicated by the *
marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the drive shaft and joint sub-assembly,
the boot may come off. Remove all grease from the drive
shaft surfaces.
7. Check that the boot installation length “L” is the specified length.
Insert a flat-tip screwdriver or similar tool into the big end of the
boot. Bleed the air from the boot to prevent boot deformation.
CAUTION:

The boot may break if the boot installation length is less than the specified length.

Do not contact inside surface of boot with the tip of the screwdriver.
8. Secure the big and small ends of the boot using new boot bands
as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
9. After installing the joint sub-assembly to the drive shaft, rotate the boot to check that it is positioned cor-
rectly. If the boot is not positioned correctly, reposition the boot and secure the boot using a new boot
band.Grease capacity : 145 − 165 g (5.11 − 5.82 oz)
RAC0049D
Boot installation length “L” : 168.4 mm (6.63 in)WDIA0288E
SFA39 5

GI-4
PRECAUTIONS
Revision: August 20072004 QX56
General PrecautionsEAS00148

Do not operate the engine for an extended period of time without
proper exhaust ventilation.
Keep the work area well ventilated and free of any flammable
materials. Special care should be taken when handling any flam-
mable or poisonous materials, such as gasoline, refrigerant gas,
etc. When working in a pit or other enclosed area, be sure to
properly ventilate the area before working with hazardous mate-
rials.
Do not smoke while working on the vehicle.

Before jacking up the vehicle, apply wheel chocks or other tire
blocks to the wheels to prevent the vehicle from moving. After
jacking up the vehicle, support the vehicle weight with safety
stands at the points designated for proper lifting before working
on the vehicle.
These operations should be done on a level surface.

When removing a heavy component such as the engine or tran-
saxle/transmission, be careful not to lose your balance and drop
them. Also, do not allow them to strike adjacent parts, especially
the brake tubes and master cylinder.

Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.

If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.

Battery posts, terminals and related accessories contain lead
and lead compounds. Wash hands after handling.

To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.

Dispose of or recycle drained oil or the solvent used for cleaning
parts in an appropriate manner.

Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel
spray and possibly a fire.

Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.

Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new
ones.

Replace inner and outer races of tapered roller bearings and needle bearings as a set.

Arrange the disassembled parts in accordance with their assembled locations and sequence.

Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.

After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.

Use only the fluids and lubricants specified in this manual.
SGI285
SGI231
SEF 2 89 H
SGI233

GI-10
HOW TO USE THIS MANUAL
Revision: August 20072004 QX56
ComponentsEAS001QX

THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques,
lubrication points, section number of the PA R T S C ATA L O G (e.g. SEC. 440) and other information neces-
sary to perform repairs.
The illustrations should be used in reference to service matters only. When ordering parts, refer to the
appropriate PA R T S C ATA L O G .
Components shown in an illustration may be identified by a circled number. When this style of illustration
is used, the text description of the components will follow the illustration.
SYMBOLS
1. Union bolt 2. Copper washer 3. Brake hose
4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Piston seal 8. Piston 9. Piston boot
10. Cylinder body 11. Sliding pin 12. Torque member mounting bolt
13. Washer 14. Sliding pin boot 15. Bushing
16. Torque member 17. Inner shim cover 18. Inner shim
19. Inner pad 20. Pad retainer 21. Pad wear sensor
22. Outer pad 23. Outer shim 24. Outer shim cover
1: PBC (Poly Butyl Cuprysil) grease
or silicone-based grease2: Rubber grease : Brake fluid
Refer to GI section for additional symbol definitions.
SFIA2959E
SAIA0749E

GI-22
HOW TO USE THIS MANUAL
Revision: August 20072004 QX56
Reference Area
The Reference Area of the wiring diagram contains references to additional electrical reference pages at the
end of the manual. If connector numbers and titles are shown in the Reference Area of the wiring diagram,
these connector symbols are not shown in the Connector Area.
AbbreviationsEAS0014M
The following ABBREVIATIONS are used:
SG I0 92 A
ABBREVIATION DESCRIPTION
A/C Air Conditioner
A/T Automatic Transaxle/Transmission
ATF Automatic Transmission Fluid
D
1Drive range 1st gear
D
2Drive range 2nd gear

IDX-2
ALPHABETICAL INDEX
Numerics
2-4WD shift solenoid valve ................................ TF-95
4LO indicator lamp ............................................. TF-90
4WD shift indicator lamp .................................... TF-85
4WD shift switch ................................................ TF-95
4WD solenoid valve ........................................... TF-95
4WD warning lamp ............................................ TF-13
A
A/C air flow ...................................................... ATC-29
A/C compressor clutch removal and installation .. ATC-
167
A/C compressor mounting ............................. ATC-166
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-14
A/C control operation (auto A/C) ...................... ATC-26
A/C diagnostic work flow (auto A/C) .............. ATC-120
A/C evaporator ............................................... ATC-175
A/C HFC134a (R134a) system identification ..... ATC-7
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure ATC-
162
A/C HFC134a (R134a) system service tools ... ATC-14
A/C HFC134a system service equipment precaution ...
ATC-11
A/C lubricant (R134a) ...................................... ATC-22
A/C lubrication oil ............................................. ATC-22
A/C operational check ....................... ATC-56, ATC-59
A/C self-diagnoses (auto A/C) ........ ATC-53, ATC-120
A/C service data specification ........................ ATC-182
A/C trouble diagnoses (auto A/C) .................... ATC-33
A/C, A - Wiring diagram ................................... ATC-41
A/T - Wiring diagram .......................................... AT-52
A/T fluid checking ...................... AT-13, AT-58, MA-21
A/T fluid cooler cleaning .................................... AT-15
A/T fluid replacement ............................. AT-13, MA-23
A/T fluid temperature sensor ........................... AT-131
A/T IND - Wiring diagram .................................... DI-41
A/T indicator ........................................................ DI-41
A/T shift lock system ........................................ AT-236
A/T trouble diagnoses ........................................ AT-43
ABS - Wiring diagram ..................................... BRC-16
ABS (anti-lock brake system) ........................... BRC-7
Accelerator control system ............................... ACC-2
Accelerator pedal position (APP) sensor . EC-556, EC-
562, EC-576
Accelerator pedal released position learning ..... EC-44
AF1B1-Wiring diagram EC-431, EC-439, EC-447, EC-
456, EC-466, EC-475, EC-487
AF1B2-Wiring diagram EC-433, EC-441, EC-449, EC-
458, EC-468, EC-477, EC-489
AF1HB1-Wiring diagram .................................. EC-355
AF1HB2-Wiring diagram .................................. EC-357
Aiming adjustment .................................. LT-31, LT-78
Air bag .............................................................. SRS-3
Air cleaner and air duct ..................................... EM-14
Air cleaner filter replacement ............................ MA-15
Air conditioner cut control ................................. EC-30
Air flow meter - See Mass air flow sensor EC-146, EC-
154
Air fuel ratio sensor 1 .. EC-429, EC-437, EC-445, EC-
454, EC-463, EC-472, EC-484
Air fuel ratio sensor 1 heater ........................... EC-354
Air mix. door motor .......................................... ATC-67
All - mode 4WD system ..................................... TF-10
Ambient sensor ............................. ATC-125, ATC-136
Angular tightening application ............................. EM-3
APPS1 - Wiring diagram ................................. EC-558
APPS2 - Wiring diagram ................................. EC-564
APPS3 - Wiring diagram ................................. EC-578
ASC/BS - Wiring diagram ............................... EC-536
ASC/SW - Wiring diagram .............................. EC-519
ASCBOF - Wiring diagram .............................. EC-622
ASCD .............................................................. EC-647
ASCD (automatic speed control device) ........... ACS-3
ASCD brake switch ........................... EC-534, EC-621
ASCD indicator lamp ....................................... EC-628
ASCD steering switch ..................................... EC-517
ASCIND - Wiring diagram ............................... EC-629
ATP switch ......................................................... TF-96
ATP warning lamp .............................................. TF-89
AUDIO - Wiring diagram .................................... AV-10
AUT/DP - Wiring diagram .................................. SE-19
Auto air conditioner - Wiring diagram .............. ATC-41
Auto anti-dazzling inside mirror ........... GW-76, GW-77
Autolamp ............................................................ LT-47
Automatic amplifier ......................................... ATC-60
Automatic transmission number .......................... GI-48
AV and NAVI control unit ................................... AV-63
AV communication line ...................................... AV-87
B
Back door trim ..................................................... EI-31
Back sonar .......................................................... DI-59
BACK/L - Wiring diagram ................................. LT-106
Back-up lamp ................................................... LT-106
Ball joint (front) ................................................ FSU-15
Basic inspection ................................................ EC-79
Battery ................................................................. SC-4
Battery/Starting/Charging System Tester SC-6, SC-12,
SC-19
BCM (Body control module) .............................. BCS-3
Block heater ...................................................... EM-73
Blower motor ................................... ATC-83, ATC-140
Body alignment ................................................ BL-174
Body component parts ..................................... BL-161
Body construction ............................................ BL-173
Body exterior paint color .................................. BL-160
Body mounting ................................................. BL-159
Body repair ....................................................... BL-160
Body sealing .................................................... BL-170
Brake booster .................................................... BR-17
Brake fluid level ................................................. MA-27
Brake hydraulic line ........................................... BR-12
Brake inspection ............................................... MA-28

IDX-4
ALPHABETICAL INDEX
Driver air bag .................................................. SRS-45
DTC work support ............................................ EC-113
DTRL - Wiring diagram ....................................... LT-37
Duct and grilles .............................................. ATC-157
DVD Player ........................................................ AV-59
E
ECM input/output signal ..................................... EC-96
ECM power supply ............................. EC-128, EC-361
ECM relay ........................................................ EC-128
ECM/PW - Wiring diagram ............................... EC-362
ECTS - Wiring diagram .................................... EC-167
Electric sunroof .................................................. RF-10
Electric throttle control actuator ......... EC-365, EC-367
Electrical load signal circuit .............................. EC-612
Electrical units location ...................................... PG-64
Electronic ignition (EI) system ........................... EC-28
Engine control circuit diagram ........................... EC-94
Engine control component parts location ........... EC-88
Engine control module (ECM) .......................... EC-351
Engine control system diagram and chart ......... EC-23
Engine coolant .................................................... CO-8
Engine coolant temperature sensor (ECTS) ... EC-165,
EC-178
Engine fail-safe system ...................................... EC-77
Engine oil ............................................................. LU-7
Engine oil filter replacement ............................. MA-16
Engine oil precautions .......................................... GI-7
Engine oil replacement ..................................... MA-16
Engine removal ................................................. EM-70
Engine room cover ............................................ EM-11
Engine serial number .......................................... GI-48
ETC1 - Wiring diagram .................................... EC-368
ETC2 - Wiring diagram .................................... EC-375
ETC3 - Wiring diagram .................................... EC-379
EVAP canister .................................................. EC-636
EVAP canister purge volume control solenoid valve ....
EC-285
, EC-496
EVAP canister vent control valve ....... EC-292, EC-504
EVAP control system (small leak) diagnosis .. EC-276,
EC-316
, EC-324
EVAP control system pressure sensor .... EC-299, EC-
302, EC-308
EVAP control system purge flow monitoring diagnosis
EC-271
EVAP vapor lines inspection ............................. MA-19
Evaporative emission (EVAP) system ............. EC-633
Evaporator ..................................................... ATC-175
Exhaust manifold .............................................. EM-19
Exhaust system ................................................... EX-3
Exhaust system inspection .................................. EX-3
Expansion valve ............................................. ATC-177
F
F/FOG - Wiring diagram ..................................... LT-71
F/PUMP - Wiring diagram ................................ EC-602
Final drive pre-inspection .................. FFD-15, RFD-12
Final drive removal and installation ... FFD-12, RFD-10
Flow charts .......................................................... GI-27
Fluid temperature sensor (A/T) ........................ AT-131
Fluids ................................................................ MA-10
Fluorescent leak detector .............................. ATC-178
Fog lamp, front ................................................... LT-69
Foot lamp ......................................................... LT-129
Freeze frame data ............................... EC-54, EC-107
Front brake solenoid valve ................. AT-151, AT-154
Front bumper ...................................................... EI-13
Front case (Transfer) ....................................... TF-125
Front combination lamp removal and installation LT-33
Front door ............................. BL-129, BL-132, GW-69
Front Door Trim ................................................... EI-31
Front drive shaft (Transfer) .............................. TF-115
Front fog lamp .................................................... LT-69
Front passenger air bag .................................. SRS-50
Front seat ........................................................... SE-96
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ............... SRS-3, SRS-57
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTTS - Wiring diagram ...................... EC-227, EC-232
Fuel cut control (at no load high engine speed) EC-30
Fuel filter replacement ......................................... FL-5
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) .......... EC-208, EC-217
Fuel injection system (Bank 2) .......... EC-208, EC-217
Fuel injector and fuel tube ................................. EM-29
Fuel level sensor ................. EC-334, EC-336, EC-338
Fuel line inspection .............................................. FL-3
Fuel precautions ................................................... GI-5
Fuel pressure check .......................................... EC-46
Fuel pressure release ....................................... EC-46
Fuel pump ....................................................... EC-601
Fuel pump and gauge .......................................... FL-5
Fuel system .......................................................... FL-3
Fuel tank .............................................................. FL-9
Fuel tank temperature sensor ........... EC-225, EC-231
Fuel tank vacuum relief valve ......................... EC-636
FUELB1 - Wiring diagram ................. EC-210, EC-219
FUELB2 - Wiring diagram ................. EC-211, EC-220
Fuse ...................................................... PG-67, PG-77
Fuse and fusible link box .................................. PG-77
Fuse block ......................................................... PG-76
Fusible link ............................................ PG-67, PG-77
G
Garage jack and safety stand ............................. GI-40
Gauges ................................................................. DI-5
Generator .......................................................... SC-17
Generic scan tool (GST) ................................. EC-116
Glass ...................................... GW-11, GW-69, GW-72
Glove box lamp ................................... LT-152, LT-153
GPS antenna ..................................................... AV-62
Grease .............................................................. MA-10
Ground distribution ............................................ PG-30

IDX-6
ALPHABETICAL INDEX
M
MAFS - Wiring diagram ..................... EC-149
, EC-156
Magnet clutch ............................... ATC-104, ATC-167
MAIN - Wiring diagram .................................... EC-128
Main oil pump (Transfer) .................................. TF-122
Mainshaft (Transfer) ........................................ TF-116
Maintenance (engine)Schedule 1 ....................... MA-6
Maintenance (engine)Schedule 2 ....................... MA-8
Major overhaul (Final drive) .............. FFD-14, RFD-13
Major overhaul (Transfer) ................................ TF-110
Malfunction indicator lamp (MIL) ........................ EC-63
Map lamp .......................................................... LT-129
Mass air flow sensor (MAFS) ............. EC-146, EC-154
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ....................... EC-631
MIL/DL - Wiring diagram .................................. EC-631
MIRROR - Wiring diagram ................................ GW-99
Misfire .............................................................. EC-243
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-152
Model variation ................................................... GI-46
Multiport fuel injection (MFI) system .................. EC-26
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system ............................... BL-44
N
NATS - Wiring diagram .................................... BL-141
NAVI - Wiring diagram ....................................... AV-79
NAVI Control Unit ............................................ AV-157
Neutral-4LO switch ............................................ TF-96
Nissan torque demand (NTD) control system .... EC-29
NVH troubleshooting (AX) ................................. FAX-4
NVH troubleshooting (EM) .................................. EM-9
NVH troubleshooting (Final drive) ..................... RFD-5
NVH troubleshooting (Propeller shaft) ................. PR-3
NVH troubleshooting (RAX) .............................. RAX-4
NVH troubleshooting (RSU) .............................. RSU-5
NVH troubleshooting (ST) .................................... PS-5
NVH troubleshooting (WT)NVH troubleshooting (WT) .
WT-3
NVIS (Nissan vehicle immobilizer system) precautions
GI-3
O
O2H2B1 - Wiring diagram ................................ EC-140
O2H2B2 - Wiring diagram ................................ EC-142
O2S2B1 - Wiring diagram .. EC-188, EC-199, EC-386,
EC-398
O2S2B2 - Wiring diagram .. EC-190, EC-201, EC-388,
EC-400
Oil cooler (engine) ............................................. LU-11
Oil filter ............................................................... LU-10
Oil filter (Transfer) ............................................ TF-107
Oil pan (engine) ................................................ EM-22
Oil pressure (engine) ........................................... LU-7
Oil pressure relief valve (engine) ......................... LU-5
Oil pump (engine) .............................................. LU-13
Oil seal replacement (engine) ........................... EM-56
Oil seal replacement (front of final drive) FFD-8, RFD-6
Oil seal replacement (side of final drive) FFD-10, RFD-
8
On board diagnostic system ............................. EC-49
ORVR (On-board Refueling Vapor Recovery) EC-640
Overheat ......................................................... EC-410
P
P/SCKT - Wiring diagram ................................. WW-54
Pantograph jack .................................................. GI-40
Park/Neutral position switch ............................ EC-546
Park/neutral position switch (A/T) .................... AT-109
Parking brake control ........................................... PB-4
Parking lamp .................................................... LT-108
PCV (positive crankcase ventilation) .............. EC-645
Periodic maintenance ......................................... MA-6
Personal lamp .................................................. LT-129
PGC/V - Wiring diagram ................... EC-287, EC-498
PHASE - Wiring diagram ................................ EC-261
Pinion bearing preload diff. ............................. RFD-21
Piston pin inspection ......................................... EM-89
Piston ring inspection ........................................ EM-90
Piston to bore clearance ................................... EM-94
Planetary carrier (Transfer) .............................. TF-127
PNP/SW - Wiring diagram .............................. EC-548
POS - Wiring diagram ..................................... EC-256
POWER - Wiring diagram ................................... PG-6
Power seat ......................................................... SE-88
Power steering fluid level .................................. MA-29
Power steering gear ........................................... PS-15
Power steering oil pump .................................... PS-26
Power steering pressure (PSP) sensor ........... EC-346
Power steering system bleeding .......................... PS-6
Power supply routing .......................................... PG-4
Power window .................................................. GW-15
PRE/SE - Wiring diagram ................. EC-304, EC-310
Precautions (General) ........................................... GI-4
Precautions in repairing high strength steel ..... BL-192
Pressure switch 1 ............................... AT-154, AT-175
Pressure switch 2 ............................................. AT-172
Pressure switch 3 ............................... AT-148, AT-178
Pressure switch 5 ............................... AT-160, AT-181
Pressure switch 6 ............................... AT-166, AT-184
Pressure test (A/T) ............................................. AT-59
Propeller shaft ........................................... PR-4, PR-8
Propeller shaft inspection .................................. MA-24
Propeller shaft on vehicle service ....................... PR-8
Propeller shaft vibration ............................ PR-4, PR-8
PS/SEN - Wiring diagram ............................... EC-347
R
R/VIEW - Wiring diagram .................................... DI-75
Radiator ............................................................ CO-10
Rear Audio Remote Control Unit ....................... AV-47

IDX-8
ALPHABETICAL INDEX
Torque convertor clutch solenoid valve ... AT-118, AT-
121
Tow truck towing ................................................. GI-42
Towing point ....................................................... GI-43
TPS1 - Wiring diagram .................................... EC-238
TPS2 - Wiring diagram .................................... EC-173
TPS3 - Wiring diagram .................................... EC-571
Traction control system - Wiring diagram ....... BRC-16
Transfer control device .................................... TF-104
Transfer control unit inspection table ................. TF-55
Transfer dropping resistor .................................. TF-96
Transfer fluid temperature sensor ...................... TF-95
Transfer motor ................................................. TF-106
Transfer motor relay .......................................... TF-97
Transfer oil replacement ................................... MA-24
Transfer serial number ........................................ GI-48
Transmission serial number ................................ GI-48
Tread-FR&RR (Dimensions) ............................... GI-49
Trim ..................................................................... EI-34
TRNSCV - Wiring diagram ............................... BL-157
Trouble diagnoses .............................................. GI-11
Turbine revolution sensor ................................ AT-134
TURN - Wiring diagram ...................................... LT-83
Turn signal lamp ................................................. LT-80
Two trip detection logic ...................................... EC-49
Two-pole lift ........................................................ GI-41
V
Vacuum hose (brake system) ............................ BR-20
Vacuum hose drawing (Engine control) ............. EC-24
Valve clearance ................................................ EM-52
Valve guide ....................................................... EM-66
Vanity mirror lamp ............................................. LT-129
VDC (vehicle dynamics control) ........................ BRC-7
VDC -Wiring diagram ...................................... BRC-16
Vehicle identification number .............................. GI-47
Vehicle recovery (freeing a stuck vehicle) .......... GI-43
Vehicle speed sensor (VSS) ............................ EC-340
VEHSEC - Wiring diagram ................................. BL-80
VENT/V - Wiring diagram .................. EC-294, EC-506
Video Monitor ..................................................... AV-60
Viscosity number (SAE) .................................... MA-11
W
W/ANT - Wiring diagram .................................... AV-49
Wait detection switch ......................................... TF-96
WARN - Wiring diagram ..................................... DI-32
Warning chime .................................................... DI-43
Warning lamps .................................................... DI-31
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-33
Water pump ...................................................... CO-15
Water temperature gauge ..................................... DI-5
Wheel alignment (front) ..................................... FSU-6
Wheel alignment (rear) ................................... RSU-27
Wheel balance .................................................. MA-25
Wheel bearing (front) ......................................... FAX-5
Wheel bearing (rear) ......................................... RAX-5
Wheel hub (rear) ............................................... RAX-5
Wheel size .......................................................... GI-49
Wheelbase (Dimensions) .................................... GI-49
Width (Dimensions) ............................................. GI-49
WINDOW - Wiring diagram .............................. GW-22
Window, door ...................................... GW-69, GW-72
Windshield ....................................................... GW-11
WIP/R - Wiring diagram ................................... WW-37
WIPER - Wiring diagram .................................... WW-9
Wiper, front ........................................................ WW-4
Wiper, rear ....................................................... WW-33
Wiring Diagram (Cell code) list ......................... PG-61
Wiring diagram (Transfer) .................................. TF-18
Wiring diagrams .................................................. GI-15
WT-T/WARN - Wiring diagram .......................... WT-10