headlamp INFINITI QX56 2004 Factory Service Manual

BCS-4
BCM (BODY CONTROL MODULE)
Revision: August 20072004 QX56
NOTE:
Headlamp has a dual system switch.
4. Example operation: (When lighting switch 1st position turned ON)

When lighting switch 1st position is turned ON, contact in combination switch turns ON. At this time if
OUTPUT 4 transistor is activated, BCM detects that voltage changes in INPUT 5.

When OUTPUT 4 transistor is ON, BCM detects that voltage changes in INPUT 5, and judges lighting
switch 1st position is ON. Then BCM sends tail lamp ON signal to IPDM E/R using CAN communica-
tion.

When OUTPUT 4 transistor is activated again, BCM detects that voltage changes in INPUT 5 and rec-
ognizes that lighting switch 1st position is continuously ON.
SKIA4959E

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: August 20072004 QX56

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Key switch
–Hazard switch
–Door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back door switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Door lock assembly LH (key cylinder switch)

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE

Sunroof system. Refer to RF-10, "SUNROOF" . NOTE

Room lamp timer. Refer to LT- 1 2 9 , "INTERIOR ROOM LAMP" .

Warning chime system. Refer to DI-43, "WARNING CHIME" .

Turn signal and hazard warning lamps system. Refer to LT-80, "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Theft warning system. Refer to BL-75, "VEHICLE SECURITY (THEFT WARNING) SYSTEM" .

IVIS (NATS) system. Refer to BL-138, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .

Headlamp, daytime light, fog lamp, tail lamp, auto light and battery saver control systems. Refer to LT- 6 ,
"HEADLAMP (FOR USA)" , LT-34, "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT-69,
"FRONT FOG LAMP" , LT- 1 0 8 , "PARKING, LICENSE PLATE AND TAIL LAMPS" , or LT- 4 7 , "AUTO
LIGHT SYSTEM" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear wiper and washer system. Refer to WW-33, "REAR WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-78, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote keyless entry system Keyfob

All-door locking actuator

Back door opener actuator

Turn signal lamp (LH, RH)
Power door lock system

Front power door lock/unlock
switch (LH, RH)

All door switch

Key switchAll-door locking actuator
Power supply (IGN) to power window and
sunroofIgnition power supply Power supply to power window and sunroof system

BCS-8
BCM (BODY CONTROL MODULE)
Revision: August 20072004 QX56
CAN Communication System DescriptionEKS007GF
Refer to LAN-5, "CAN COMMUNICATION" .
Power supply (BAT) to power window and
sunroofBattery power supply Power supply to power window and sunroof system
Panic alarm

Key switch

KeyfobIPDM E/R
Auto light system

Auto light sensor

Combination switchIPDM E/R
Battery saver control

Ignition switch

Combination switch

Front door switch LH

Front door switch RHIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Keyfob

Main power window and door
lock/unlock switch

Front door lock assembly LH
(key cylinder switch)

All door switchInterior room lamp
Key warning chime

Key switch

Front door switch LHCombination meter (warning buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LHCombination meter (warning buzzer)
Vehicle-speed-sensing intermittent wiper

Combination switch

Combination meterIPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECM
Low tire pressure warning system Remote keyless entry receiver

Combination meter

Display control unit
Trailer tow Combination switch Trailer turn signal lamp
Vehicle security system

Remote keyless entry receiver
(Keyfob)

Main power window and door
lock/unlock switch

Power window and door lock/
unlock switch RH

Front door lock assembly LH
(key cylinder switch)

All door switch

Glass hatch ajar switch

IPDM E/R

Security indicator lamp System Input Output

BCS-12
BCM (BODY CONTROL MODULE)
Revision: August 20072004 QX56
4. Select item to be diagnosed on “SELECT TEST ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
WORK SUPPORT
Operation Procedure
1. Touch "BCM" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch "RESET SETTING VALUE" on "SELECT WORK ITEM" screen.
4. Touch "START".
5. "RESET SETTING VALUE OK?" is displayed, and touch "YES".
6. The setting will be changed and "COMPLETED" will be displayed.
7. Touch "END".
LKIA0183E
System and itemCONSULT-II
displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−DIAG
RESULTSCAN DIAG
SUPPORT
MNTRDATA
MONITORECU
PA R T
NUMBERACTIVE
TESTCONFIG-
URA-
TION
BCM BCM×× × × ×
Power door lock sys-
temDOOR LOCK×××
Rear defoggerREAR
DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remote keyless
entry systemMULTI
REMOTE ENT×××
Headlamp HEAD LAMP×××
Wiper WIPER××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch
signal
Air conditioner
switch signalAIR
CONDITIONER×
Combination switch COMB SW×
IVIS (NATS) IMMU××
Interior lamp battery
saverBATTERY
SAVER×××
Back door BACK DOOR××
Retained power con-
trolRETAINED
PWR×××

BL-2Revision: August 20072004 QX56 Trouble Diagnosis Procedure ................................. 59
BCM Power Supply and Ground Circuit Check ...... 59
Trouble Diagnoses .................................................. 60
SYMPTOM CHART ............................................. 60
Key Switch (Insert) Check ...................................... 62
Door Switch Check ................................................. 63
Keyfob Battery and Function Check ....................... 65
Remote Keyless Entry Receiver System Check ..... 66
ACC Power Check .................................................. 68
IPDM E/R Operation Check .................................... 68
Check Hazard Function .......................................... 70
Check Horn Function .............................................. 70
Check Headlamp Function ..................................... 70
Check Map Lamp Illumination Function ................. 70
ID Code Entry Procedure ....................................... 71
KEYFOB ID SET UP WITH CONSULT-II ............ 71
KEYFOB ID SET UP WITHOUT CONSULT-II ..... 73
Keyfob Battery Replacement .................................. 74
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 75
Component Parts and Harness Connector Location ... 75
System Description ................................................. 76
DESCRIPTION .................................................... 76
POWER SUPPLY AND GROUND CIRCUIT ....... 76
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ..................................................................... 77
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION .................................................................. 78
VEHICLE SECURITY SYSTEM DEACTIVATION ... 78
PANIC ALARM OPERATION ............................... 78
CAN Communication System Description .............. 78
Schematic ............................................................... 79
Wiring Diagram — VEHSEC — .............................. 80
............................................................................. 80
............................................................................. 81
............................................................................. 82
............................................................................. 83
............................................................................. 84
Terminals and Reference Value for BCM ................ 85
Terminals and Reference Value for IPDM E/R ........ 86
CONSULT-II Function (BCM) .................................. 86
CONSULT-II INSPECTION PROCEDURE .......... 87
CONSULT-II APPLICATION ITEM ....................... 89
Trouble Diagnosis ................................................... 90
WORK FLOW ...................................................... 90
Preliminary Check .................................................. 91
Symptom Chart ....................................................... 92
Door Switch Check ................................................. 93
Hood Switch Check ................................................ 95
Combination Meter (Security Indicator Lamp)
Check ..................................................................... 97
Front Door Lock Assembly LH (Key Cylinder Switch)
Check ..................................................................... 98
Vehicle Security Horn Alarm Check ......................100
Vehicle Security Headlamp Alarm Check .............100
Door Lock/Unlock Switch Check ..........................100
AUTOMATIC BACK DOOR SYSTEM .....................101
Component Parts and Harness Connector Location .101
System Description ...............................................102
OPERATION DESCRIPTION ............................102Schematic ............................................................. 107
Wiring Diagram — B/CLOS — .............................. 108
Terminals and Reference Value for Back Door Con-
trol Unit ..................................................................113
Terminals and Reference Value for BCM ..............114
Trouble Diagnosis Procedure ................................115
Self-Diagnosis Procedures ...................................115
INPUT SIGNAL CHECK MODE .........................115
OPERATING CHECK MODE .............................115
Diagnosis Chart ....................................................116
Back Door Power Supply and Ground Circuit
Inspection ..............................................................117
Power Liftgate Switch System Inspection .............118
GLASS HATCH AJAR SWITCH CHECK ...........119
Back Door Close (Close) Switch System Inspection . 120
Back Door Close (Cancel) Switch System Inspec-
tion ........................................................................ 121
Pinch Strip System Inspection .............................. 122
Back Door Warning Chime System Inspection ..... 123
Half-Latch Switch System Inspection .................... 124
Open Switch System Inspection ........................... 125
Close Switch System Inspection ........................... 126
Back Door Handle Switch System Inspection ....... 127
Cinch Latch Motor System Inspection .................. 128
DOOR ...................................................................... 129
Fitting Adjustment ................................................. 129
FRONT DOOR ................................................... 129
REAR DOOR ..................................................... 129
STRIKER ADJUSTMENT .................................. 129
Removal and Installation ....................................... 130
FRONT DOOR ................................................... 130
REAR DOOR ..................................................... 130
BACK DOOR ..................................................... 131
FRONT DOOR LOCK .............................................. 132
Component Structure ............................................ 132
Removal and Installation ....................................... 132
REMOVAL .......................................................... 132
INSTALLATION .................................................. 134
Disassembly and Assembly .................................. 134
DOOR KEY CYLINDER ASSEMBLY ................. 134
REAR DOOR LOCK ................................................ 135
Component Structure ............................................ 135
Removal and Installation ....................................... 135
REMOVAL .......................................................... 135
INSTALLATION .................................................. 135
BACK DOOR LOCK ................................................ 136
Power Back Door Opener ..................................... 136
REMOVAL ......................................................... 136
INSTALLATION ................................................. 136
Door Lock Assembly ............................................. 137
REMOVAL ......................................................... 137
INSTALLATION ................................................. 137
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ...................................................................... 138
Component Parts and Harness Connector Location . 138
System Description ............................................... 139
System Composition ............................................. 139
ECM Re-communicating Function ........................ 140
Wiring Diagram — NATS — .................................. 141

BL-12
HOOD
Revision: August 20072004 QX56
HOODPFP:F5100
Fitting AdjustmentEIS0 02 R4
1. Hood hinge 2. Hood stay 3. Hood lock assembly
4. Hood assembly 5. Front grille 6. Headlamp
7. Front fender 8. Front bumper fascia
LIIA1442E

HOOD
BL-13
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the hood lock assembly and adjust the height by rotating the bumper rubber until the hood clear-
ance of hood and fender becomes 1 mm (0.04 in) lower than fitting standard dimension.
2. Temporarily tighten the hood lock, and position it by engaging it with the hood striker. Check the lock and
striker for looseness, and tighten the lock bolts to the specified torque.
3. Adjust the clearance and surface height of hood and fender according to the fitting standard dimension by
rotating right and left bumper rubbers.
CAUTION:
Adjust right/left gap between hood and each part to the following specification.
HOOD LOCK ADJUSTMENT
1. Move the hood lock to the left or right so that striker center is vertically aligned with hood lock center
(when viewed from vehicle front).
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height or by pressing it lightly approx.
3 kg (29 N, 7lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or
higher.
3. After adjusting hood lock, tighten the lock bolts to the specified
torque.
Removal and Installation of Hood AssemblyEIS002R5
1. Support the hood striker with a proper material to prevent it from
falling.
WAR NIN G:
Body injury may occur if no supporting rod is holding the
hood open when removing the damper stay.
2. Remove the hinge nuts from the hood to remove the hood
assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
Installation is in the reverse order of removal.Hood and headlamp (B–B) : Less than 2.0 mm
PIIA3806E
LIIA1443E

BL-48
REMOTE KEYLESS ENTRY SYSTEM
Revision: August 20072004 QX56
Remote keyless entry system turns on interior lamp and ignition keyhole illumination (for 30 seconds) with
input of UNLOCK signal from keyfob.
For detailed description, refer to LT- 1 3 1 , "
ROOM LAMP TIMER OPERATION" .
Panic Alarm Operation
When key switch is OFF (ignition key is not inserted in key cylinder), remote keyless entry system turns on and
off horn and headlamp intermittently with input of PANIC ALARM signal from keyfob.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from keyfob.
Keyless Power Window Down (Open) Operation
When keyfob unlock switch is turned ON with ignition switch OFF, and the switch is detected to be on continu-
ously for 3 seconds, the driver's door and passenger's door power windows are simultaneously opened.
Power window is operated to open and the operation continues as long as the keyfob unlock switch is
pressed.
CAN Communication System DescriptionEIS002RQ
Refer to LAN-5, "CAN COMMUNICATION" .

REMOTE KEYLESS ENTRY SYSTEM
BL-61
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
Hazard reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Horn reminder OK)1. Check hazard reminder mode with CONSULT-II
NOTE:
Hazard reminder mode can be changed.
First check the hazard reminder mode setting.BL-57
2. Check hazard function with hazard switch —
3. Replace BCM.BCS-19
Horn reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Hazard reminder OK)1. Check horn reminder mode with CONSULT-II
NOTE:
Horn reminder mode can be changed.
First check the horn reminder mode setting.BL-57
2. Check horn function with horn switch —
3. IPDM E/R operation checkBL-68
4. Replace BCM.BCS-19
Back door open/close operation is not carried out
with keyfob operation.
(The automatic back door system is normal.)1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241)BL-652. Key switch (insert) checkBL-62
3. Check that glass hatch is closed —
4. Remote keyless entry receiver systemBL-68
5. Replace BCM.BCS-19
Room lamp, ignition keyhole illumination and step
lamp operation do not activate properly.1. Room lamp operation checkBL-70
2. Ignition kehole illumination operation checkBL-70
3.Step lamp operation checkLT- 1 3 0
4. Door switch checkBL-63
5. Replace BCM.BCS-19
Panic alarm (horn and headlamp) does not activate
when panic alarm button is continuously pressed.1. Keyfob battery and function check (use Remote Keyless Entry
Tester J-43241)
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning.BL-65
2. Key switch and key lock solenoid (insert) checkBL-62
3. Replace BCM.BCS-19
Auto door lock operation does not activate properly.
(All other remote keyless entry functions OK.)1. Check auto door lock operation mode with CONSULT-II
NOTE:
Auto door lock operation mode can be changed.
First check the auto door lock operation mode setting.BL-57
2. Replace BCM.BCS-19
Keyless power window down (open) operation does
not activate properly.
(All other remote keyless entry functions OK.)1. Check power window down operation mode with CONSULT-II
NOTE:
Power window down operation mode can be changed.
First check the power window down operation mode setting.BL-57
2. Check power window function with switch —
3. Replace BCM.BCS-19
Symptom Diagnoses/service procedureReference
page

BL-70
REMOTE KEYLESS ENTRY SYSTEM
Revision: August 20072004 QX56
Check Hazard FunctionEIS002S7
1. CHECK HAZARD WARNING LAMP
Does hazard indicator flash with hazard switch?
Ye s o r N o
Yes >> Hazard warning lamp circuit is OK.
No >> Check hazard indicator. Refer to LT- 8 0 , "
TURN SIGNAL AND HAZARD WARNING LAMPS" .
Check Horn FunctionEIS002S8
First, perform the "SELF-DIAG RESULTS" in "BCM" with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated in "SELF-DIAG RESULTS" of "BCM".
1. CHECK HORN FUNCTION
Does horn sound with horn switch?
Ye s o r N o
Yes >> Horn circuit is OK.
No >> Check horn circuit. Refer to WW-56, "
HORN" .
Check Headlamp FunctionEIS002S9
First, perform the "SELF-DIAG RESULTS" in "BCM" with CONSULT-II, then perform the trouble diagnosis of
malfunction system indicated in "SELF-DIAG RESULTS" of "BCM".
1. CHECK HEADLAMP OPERATION
Does headlamp come on when turning lighting switch ON?
Ye s o r N o
Yes >> Headlamp operation circuit is OK.
No >> Check headlamp circuit. Refer to LT- 6 , "
HEADLAMP (FOR USA)" .
Check Map Lamp Illumination FunctionEIS002SA
1. CHECK MAP LAMP ILLUMINATION FUNCTION
When map lamp switch is in DOOR position, open the front door LH or RH.
OK or NG
OK >> Map lamp illumination circuit is OK.
NG >> Check map lamp illumination circuit. Refer to LT- 1 5 2 , "
ILLUMINATION" . Map lamp and ignition keyhole illumination should illuminate.