hood open INFINITI QX56 2004 Factory Service Manual

TROUBLE DIAGNOSIS
ATC-113
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
PERFORMANCE CHART
Test Condition
Testing must be performed as follows:
Te s t R e a d i n g
Recirculating-to-discharge Air Temperature Table
Ambient Air Temperature-to-operating Pressure Table
Vehicle location Indoors or in the shade (in a well-ventilated place)
Doors Closed
Door window Open
Hood Open
TEMP. Max. COLD
Mode switch
(Ventilation) set
Recirculation (REC) switch
(Recirculation) set
Fan (blower) speedMax. speed set
Engine speed Idle speed
Operate the air conditioning system for 10 minutes before taking measurements.
Inside air (Recirculating air) at blower assembly inlet
Discharge air temperature at center ventilator
°C (°F) Relative humidity
%Air temperature
°C (°F)
50 - 6020 (68) 5.3 - 6.5 (42 - 44)
25 (77) 9.7 - 11.5 (49 - 53)
30 (86) 13.8 - 16.3 (57 - 61)
35 (95) 18.0 - 21.2 (64 - 70)
40 (104) 22.2 - 25.7 (72 - 78)
60 - 7020 (68) 6.5 - 7.7 (44 - 46)
25 (77) 11.5 - 13.3 (53 - 56)
30 (86) 16.3 - 18.8 (61 - 66)
35 (95) 21.2 - 24.0 (70 - 75)
40 (104) 25.7 - 29.2 (78 - 85)
Ambient air
High-pressure (Discharge side)
kPa (kg/cm
2 , psi)Low-pressure (Suction side)
kPa (kg/cm2 , psi) Relative humidity
%Air temperature
°C (°F)
50 - 7020 (68)680 - 840
(6.94 - 8.57, 98.6 - 121.8)160 - 198
(1.63 - 2.02, 23.2 - 28.7)
25 (77)800 - 985
(8.16 - 10.05, 116.0 - 142.8)198 - 245
(2.02 - 2.50, 28.7 - 35.5)
30 (86)940 - 1,150
(9.59 - 11.73, 136.3 - 166.8)225 - 278
(2.30 - 2.84, 32.6 - 40.3)
35 (95)1,160 - 1,410
(11.83 - 14.38, 168.2 - 204.5)273 - 335
(2.78 - 3.42, 39.6 - 48.6)
40 (104)1,325 - 1,620
(13.52 - 16.52, 192.1 - 234.9)325 - 398
(3.32 - 4.06, 47.1 - 57.7)

BL-2Revision: August 20072004 QX56 Trouble Diagnosis Procedure ................................. 59
BCM Power Supply and Ground Circuit Check ...... 59
Trouble Diagnoses .................................................. 60
SYMPTOM CHART ............................................. 60
Key Switch (Insert) Check ...................................... 62
Door Switch Check ................................................. 63
Keyfob Battery and Function Check ....................... 65
Remote Keyless Entry Receiver System Check ..... 66
ACC Power Check .................................................. 68
IPDM E/R Operation Check .................................... 68
Check Hazard Function .......................................... 70
Check Horn Function .............................................. 70
Check Headlamp Function ..................................... 70
Check Map Lamp Illumination Function ................. 70
ID Code Entry Procedure ....................................... 71
KEYFOB ID SET UP WITH CONSULT-II ............ 71
KEYFOB ID SET UP WITHOUT CONSULT-II ..... 73
Keyfob Battery Replacement .................................. 74
VEHICLE SECURITY (THEFT WARNING) SYSTEM ... 75
Component Parts and Harness Connector Location ... 75
System Description ................................................. 76
DESCRIPTION .................................................... 76
POWER SUPPLY AND GROUND CIRCUIT ....... 76
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ..................................................................... 77
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION .................................................................. 78
VEHICLE SECURITY SYSTEM DEACTIVATION ... 78
PANIC ALARM OPERATION ............................... 78
CAN Communication System Description .............. 78
Schematic ............................................................... 79
Wiring Diagram — VEHSEC — .............................. 80
............................................................................. 80
............................................................................. 81
............................................................................. 82
............................................................................. 83
............................................................................. 84
Terminals and Reference Value for BCM ................ 85
Terminals and Reference Value for IPDM E/R ........ 86
CONSULT-II Function (BCM) .................................. 86
CONSULT-II INSPECTION PROCEDURE .......... 87
CONSULT-II APPLICATION ITEM ....................... 89
Trouble Diagnosis ................................................... 90
WORK FLOW ...................................................... 90
Preliminary Check .................................................. 91
Symptom Chart ....................................................... 92
Door Switch Check ................................................. 93
Hood Switch Check ................................................ 95
Combination Meter (Security Indicator Lamp)
Check ..................................................................... 97
Front Door Lock Assembly LH (Key Cylinder Switch)
Check ..................................................................... 98
Vehicle Security Horn Alarm Check ......................100
Vehicle Security Headlamp Alarm Check .............100
Door Lock/Unlock Switch Check ..........................100
AUTOMATIC BACK DOOR SYSTEM .....................101
Component Parts and Harness Connector Location .101
System Description ...............................................102
OPERATION DESCRIPTION ............................102Schematic ............................................................. 107
Wiring Diagram — B/CLOS — .............................. 108
Terminals and Reference Value for Back Door Con-
trol Unit ..................................................................113
Terminals and Reference Value for BCM ..............114
Trouble Diagnosis Procedure ................................115
Self-Diagnosis Procedures ...................................115
INPUT SIGNAL CHECK MODE .........................115
OPERATING CHECK MODE .............................115
Diagnosis Chart ....................................................116
Back Door Power Supply and Ground Circuit
Inspection ..............................................................117
Power Liftgate Switch System Inspection .............118
GLASS HATCH AJAR SWITCH CHECK ...........119
Back Door Close (Close) Switch System Inspection . 120
Back Door Close (Cancel) Switch System Inspec-
tion ........................................................................ 121
Pinch Strip System Inspection .............................. 122
Back Door Warning Chime System Inspection ..... 123
Half-Latch Switch System Inspection .................... 124
Open Switch System Inspection ........................... 125
Close Switch System Inspection ........................... 126
Back Door Handle Switch System Inspection ....... 127
Cinch Latch Motor System Inspection .................. 128
DOOR ...................................................................... 129
Fitting Adjustment ................................................. 129
FRONT DOOR ................................................... 129
REAR DOOR ..................................................... 129
STRIKER ADJUSTMENT .................................. 129
Removal and Installation ....................................... 130
FRONT DOOR ................................................... 130
REAR DOOR ..................................................... 130
BACK DOOR ..................................................... 131
FRONT DOOR LOCK .............................................. 132
Component Structure ............................................ 132
Removal and Installation ....................................... 132
REMOVAL .......................................................... 132
INSTALLATION .................................................. 134
Disassembly and Assembly .................................. 134
DOOR KEY CYLINDER ASSEMBLY ................. 134
REAR DOOR LOCK ................................................ 135
Component Structure ............................................ 135
Removal and Installation ....................................... 135
REMOVAL .......................................................... 135
INSTALLATION .................................................. 135
BACK DOOR LOCK ................................................ 136
Power Back Door Opener ..................................... 136
REMOVAL ......................................................... 136
INSTALLATION ................................................. 136
Door Lock Assembly ............................................. 137
REMOVAL ......................................................... 137
INSTALLATION ................................................. 137
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ...................................................................... 138
Component Parts and Harness Connector Location . 138
System Description ............................................... 139
System Composition ............................................. 139
ECM Re-communicating Function ........................ 140
Wiring Diagram — NATS — .................................. 141

HOOD
BL-13
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the hood lock assembly and adjust the height by rotating the bumper rubber until the hood clear-
ance of hood and fender becomes 1 mm (0.04 in) lower than fitting standard dimension.
2. Temporarily tighten the hood lock, and position it by engaging it with the hood striker. Check the lock and
striker for looseness, and tighten the lock bolts to the specified torque.
3. Adjust the clearance and surface height of hood and fender according to the fitting standard dimension by
rotating right and left bumper rubbers.
CAUTION:
Adjust right/left gap between hood and each part to the following specification.
HOOD LOCK ADJUSTMENT
1. Move the hood lock to the left or right so that striker center is vertically aligned with hood lock center
(when viewed from vehicle front).
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height or by pressing it lightly approx.
3 kg (29 N, 7lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or
higher.
3. After adjusting hood lock, tighten the lock bolts to the specified
torque.
Removal and Installation of Hood AssemblyEIS002R5
1. Support the hood striker with a proper material to prevent it from
falling.
WAR NIN G:
Body injury may occur if no supporting rod is holding the
hood open when removing the damper stay.
2. Remove the hinge nuts from the hood to remove the hood
assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
Installation is in the reverse order of removal.Hood and headlamp (B–B) : Less than 2.0 mm
PIIA3806E
LIIA1443E

HOOD
BL-15
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
INSTALLATION
1. Pull the hood lock cable through the panel hole to the engine room.
Be careful not to bend the cable too much, keeping the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the grommet, and push
the grommet into the panel hole securely.
3. Apply sealant to the grommet (at * mark) properly.
4. Install the primary and secondary cables securely to the hood
lock.
5. Install the hood lock and the secondary hood lock release
assemblies.
6. Check the hood lock adjustment and hood opener operation.
Refer to BL-12, "
Fitting Adjustment" .
Hood Lock Control InspectionEIS002R7
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
2. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
3. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown in the figure.
PIIA0173E
PIIA0174E
PIIA1086E
PIIA0176E

BL-76
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: August 20072004 QX56
System DescriptionEIS002SE
DESCRIPTION
Operation Flow

Setting the vehicle security system
Initial condition

Ignition switch is in OFF position.
Disarmed phase

When the vehicle is being driven or when doors or glass hatch is open, the vehicle security system is set
in the disarmed phase on the assumption that the owner is inside or near the vehicle.
Pre-armed phase and armed phase

There are three conditions to enable the vehicle security system to turn into the "pre-armed" phase and
transition into armed phase. The initial requirements are that hood, glass hatch and all doors must be
closed (ignition key removed) for the transition to take place. Those three conditions are:
1. Locking vehicle with either front power door lock switch before exiting vehicle and closing all doors.
2. Using keyfob to lock already closed doors after leaving the vehicle.
3. Using driver key cylinder switch to lock already closed doors after leaving the vehicle.

Upon any of the above three steps taking place, the security indicator lamp illuminates for 30 seconds,
then the system automatically shifts into the "armed" phase.
Canceling the set vehicle security system
When one of the following operations is performed, the armed phase is canceled.
1. Unlock the doors with the key or the keyfob.
2. Open the power back door with the keyfob. When the power back door is closed after opening the power
back door with the keyfob, the system returns to the armed phase.
Activating the alarm operation of the vehicle security system
Make sure the system is in the armed phase.
When one of the following operations is performed, the system sounds the horns and flashes the headlamps
for about 50 seconds.
1. Engine hood, glass hatch or any door is opened before unlocking door with key or keyfob.
2. Door is unlocked without using key or keyfob.
3. Power back door is opened without using the keyfob.
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times

through 10A fuse [No.19, located in the fuse block (J/B)]
PIIA1367E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56

to combination meter (security indicator lamp) terminal 8.

through 50A fusible link (letter f , located in the fuse and fusible link box)

to BCM terminal 70.

through 15A fuse [No. 22, located in the fuse block (J/B)]

to BCM terminal 57.

through 15A fuse (No. 25, located in the fuse and fusible link box)

to horn relay terminal 2.

through 20A fuse (No. 52, located in the IPDM E/R) and

through 20A fuse (No. 53, located in the IPDM E/R),

to IPDM E/R internal CPU.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 67

through body grounds M57, M61 and M79 and

to IPDM E/R terminals 38 and 59

through body ground E9, E15 and E24.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors, hood and glass hatch.
To activate the vehicle security system, BCM must receive signals indicating the doors, hood and glass hatch
are closed and the doors are locked.
When a door or glass hatch is open, BCM terminal 12, 13, 42, 43, 47 or 48 receives a ground signal from that
switch. When the hood is open, IPDM E/R terminal 41 receives a ground signal from the hood switch.
When the front door switch LH is ON (door is open), ground is supplied

to BCM terminal 47

through front door switch LH terminal 2

through front door switch LH case ground.
When the front door switch RH is ON (door is open), ground is supplied

to BCM terminal 12

through front door switch RH terminal 2

through front door switch RH case ground.
When the rear door switch LH is ON (door is open), ground is supplied

to BCM terminal 48

through rear door switch LH terminal 2

through rear door switch LH case ground.
When the rear door switch RH is ON (door is open), ground is supplied

to BCM terminal 13

through rear door switch RH terminal 2

through rear door switch RH case ground.
When the back door latch (door ajar switch) is ON (door is open), ground is supplied

to BCM terminal 43

through back door latch (door ajar switch) terminal 7

through back door latch (door ajar switch) terminal 8

through grounds B7 and B19.
When the glass hatch ajar switch is ON (hatch is open) ground is supplied

to BCM terminal 42

through glass hatch ajar switch terminal +

through glass hatch ajar switch case ground.

BL-78
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: August 20072004 QX56
When the hood switch is ON (hood is open) ground is supplied

to IPDM E/R terminal 41

through hood switch terminal 2

through hood switch terminal 1

through grounds E9, E15 and E24.
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by

opening a door

opening the hood

opening the glass hatch

unlocking door without using the key or keyfob.
The vehicle security system will be triggered once the system is in armed phase,

when BCM receives a ground signal at terminals 12, 13, 47, 48 (door switch), terminal 42 (glass hatch ajar
switch) or terminal 43 [back door latch (door ajar switch)], or IPDM E/R terminal 41 (hood switch) receives
a ground signal.
Power is supplied at all times

to horn relay terminal 2

through 15A fuse (No. 25, located in fuse and fusible link box).
When the vehicle security system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to headlamp high relay and

to horn relay terminal 1.
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked with the key or keyfob.
When the key is used to unlock the front door LH, BCM terminal 22 receives signal

from terminal 14 of the main power window and door lock/unlock switch.
When the BCM receives this signal or unlock signal from keyfob, the vehicle security system is deactivated.
(Disarmed phase)
PANIC ALARM OPERATION
Remote keyless entry system may or may not operate vehicle security system (horn and headlamps) as
required.
When the remote keyless entry system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to headlamp high relay and

to horn relay terminal 1.
The headlamp flashes and the horn sounds intermittently.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from keyfob.
CAN Communication System DescriptionEIS002SF
Refer to LAN-5, "CAN COMMUNICATION" .

BL-86
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: August 20072004 QX56
Terminals and Reference Value for IPDM E/REIS002SJ
*1: when horn reminder is ON.
*2: L/W is for USA.
*3: Y is for Canada.
CONSULT-II Function (BCM)EIS002SK
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
Terminal Wire
ColorItem ConditionVoltage (V)
(Approx.)
38 B Ground — 0
39 W CAN-H — —
40 R CAN-L — —
41 Y/B Hood switchHood closed OFF Battery voltage
Hood open ON 0V
45 G/W Horn relayWhen doors locks are operated
using keyfob (OFF → ON) *1Battery voltage → 0V
52 L Headlamp low (LH)Ignition
SW ONLighting
switch
2ND posi-
tionOFF 0V
ON Battery voltage
54 R/Y Headlamp low (RH)Ignition
SW ONLighting
switch
2ND posi-
tionOFF 0V
ON Battery voltage
55 G Headlamp high (LH)Ignition
SW ONLighting
switch
HIGH or
PA S S
positionOFF 0V
ON Battery voltage
56L/W *2
Y *3Headlamp high (RH)Ignition
SW ONLighting
switch
HIGH or
PA S S
positionOFF 0V
ON Battery voltage
59 B Ground — 0
BCM
diagnostic test itemDiagnostic mode Description
Inspection by partWORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the
BCM for setting the status suitable for required operation, input/output sig-
nals are received from the BCM and received date is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TESTOperation of electrical loads can be checked by sending drive signal to
them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTRThe result of transmit/receive diagnosis of CAN communication can be
read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-89
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
CONSULT-II APPLICATION ITEM
Data Monitor
Active Test
Work Support
Monitored Item Description
DOOR SW-AS Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch LH.
BACK DOOR SW Indicates [ON/OFF] condition of back door latch.
TRNK OPEN MNTR Indicates [ON/OFF] condition of glass hatch ajar switch.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEYLESS UNLOCK Indicates [ON/OFF] condition of unlock signal from keyfob.
KEYLESS LOCK Indicates [ON/OFF] condition of lock signal from keyfob.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from door key cylinder switch.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.
KEYLESS PBD Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
HOOD SW Indicates [ON/OFF] condition of hood switch.
Test Item Description
THEFT INDThis test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-II screen is touched.
HEADLAMP (HI)This test is able to check vehicle security lamp operation. The highbeam headlamps will be acti-
vated for 0.5 seconds after “ON” on CONSULT-II screen is touched.
VEHICLE SECURITY HORNThis test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-II screen is touched.
Test Item Description
SECURITY ALARM SET This mode can confirm and change security alarm ON-OFF setting.
THEFT ALM TRGThe switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR”
on CONSULT-II screen.

BL-92
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: August 20072004 QX56
Symptom ChartEIS002SN
*1: Make sure the system is in the armed phase.PROCEDURE
Diagnostic procedure
SYMPTOM
1Vehicle security
system cannot be
set by ····Door switch Refer to BL-93, "
Door Switch Check" .
Lock/unlock switch Refer to BL-100, "
Door Lock/Unlock Switch Check" .
Door outside keyRefer to BL-98, "
Front Door Lock Assembly LH (Key Cylinder Switch)
Check" .
BCM If the above systems are “OK”, replace BCM.
Security indicator does not turn “ON”.Refer to BL-97, "
Combination Meter (Security Indicator Lamp) Check" .
If the above systems are “OK”, replace BCM.
2*1 Vehicle secu-
rity system does
not alarm when
····Any door, hood or glass hatch
is opened.Refer to BL-93, "
Door Switch Check" .
Refer to BL-95, "
Hood Switch Check" .
If the above systems are “OK”, replace BCM.
3Vehicle security
alarm does not
activate.Horn alarmRefer to BL-100, "
Vehicle Security Horn Alarm Check" .
If the above systems are “OK”, check horn system.
Refer to WW-56, "
HORN" .
Headlamp alarmRefer to BL-100, "
Vehicle Security Headlamp Alarm Check" .
If the above systems are “OK”, replace BCM.
4Vehicle security
system cannot be
canceled by ····Door outside keyRefer to BL-98, "
Front Door Lock Assembly LH (Key Cylinder Switch)
Check" .
If the above systems are “OK”, check main power window and door lock/
unlock switch.
KeyfobCheck remote keyless entry function. Refer toBL-65, "
Keyfob Battery and
Function Check"
If the above systems are “OK”, replace BCM.