window INFINITI QX56 2006 Factory Service Manual

REAR WINDOW DEFOGGERGW-85
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
Rear Window Defogger Switch Circuit CheckEIS005YX
1. CHECK REAR WINDOW DEFOGGER SWITCH OPERATION
With CONSULT-II
Check ( “REAR DEF SW ”, “IGN ON SW ”) in DATA MONITOR mode
with CONSULT-II. Refer to GW-82, "
DATA MONITOR" .
Without CONSULT-II
1. Turn ignition switch ON.
2. Check voltage between BCM connector and ground.
OK or NG
OK >> Rear window defogger switch check is OK.
NG >> GO TO 2.
2. CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and front air control.
3. Check continuity between BCM connector M18 terminal 9 and front air control connector M49 terminal 11.
4. Check continuity between BCM connector M18 terminal 9 and ground
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness. When rear window defogger switch is turned to ON
REAR DEF SW
: ON
When ignition switch is turned to ON
IGN ON SW : ON
PIIA2373E
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
M18 9 Ground Rear window defogger
switch is pressed.
0
Rear window defogger
switch is OFF. 5
WIIA0523E
9 - 11
: Continuity should exist.
9 - Ground : Continuity should not exist.
LIIA2035E

GW-86
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M18 terminal 9 and ground.
OK or NG
OK >> Replace front air control. Refer to ATC-144, "FRONT
AIR CONTROL" .
NG >> Replace BCM. Refer to BCS-20, "
BCM" .
Rear Window Defogger Circuit CheckEIS0062Z
1. CHECK FUSES
Check if any of the following fuses in IPDM E/R are blown.
NOTE:
Refer to GW-74, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse, refer to GW-
74, "Component Parts and Harness Connector Location" .
2. CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger connector D406 terminal + and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4. 9 - Ground
: Approx. 5
WIIA0523E
COMPONENT PARTS AMPEREFUSE NO.
IPDM E/R 15A46
IPDM E/R 15A47
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
D406 + Ground Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF. 0
LIIA0655E

REAR WINDOW DEFOGGERGW-87
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
3. CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear window defogger connector D604 terminal - and ground.
OK or NG
OK >> Check filament. Refer to GW-91, "Filament Check" .

If filament is OK.
Check the condition of the harness and the connector.

If filament is NG.
Repair filament.
NG >> Repair or replace harness.
4. CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R connector E124 terminal 60 and ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-30, "Removal and Installation of IPDM E/R" .
NG >> Repair or replace harness.
Door Mirror Defogger Power Supply Circuit CheckEIS005Z0
1. CHECK FUSE
Check if any of the following fuses in fuse block (J/B) are blown.
NOTE:
Refer to GW-74, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
GW-74, "
Component Parts and Harness Connector Location" .
- - Ground
: Continuity should exist.
LIIA0409E
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
E124 60 Ground Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF. 0
WIIA0525E
COMPONENT PARTS
AMPEREFUSE NO.
IPDM E/R 15A43

GW-88
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
2. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT 2
Check voltage between IPDM E/R connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace IPDM E/R. Refer to PG-30, "
Removal and
Installation of IPDM E/R" .
3. CHECK DOOR MIRROR DEFOGGER CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and door mirror LH or RH.
3. Check continuity between IPDM E/R connector E120 terminal 23 and door mirror connector D4 (LH) or D107 (RH) terminal 10.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
Check continuity between each door mirror connector D4 (LH) or
D107 (RH) terminal 11 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness.
5. CHECK DOOR MIRROR DEFOGGER
Check continuity between each door mirror LH or RH terminals 10
and 11.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace malfunctioning door mirror LH or RH. Refer to GW-94, "
Door Mirror Assembly" .
Connector Terminals
ConditionVoltage (V)
(Approx.)
(+) (-)
E120 23 Ground Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF 0
LIIA0977E
23 - 10
: Continuity should exist.
WIIA0529E
11 - Ground: Continuity should exist.
LIIA1454E
10 - 11 : Continuity should exist.
LIIA2725E

REAR WINDOW DEFOGGERGW-89
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
Door Mirror LH (Door Mirror Defogger) Circuit CheckEIS005Z1
1. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror LH.
3. Turn ignition switch ON.
4. Check voltage between door mirror LH connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror LH connector D4 terminal 11 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror LH terminals 10 and 11.
OK or NG
OK >> Repair or replace harness.
NG >> Replace door mirror LH. Refer to GW-94, "
Door Mirror
Assembly" .
ConnectorTe r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
D4 10 Ground Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF 0
LIIA1456E
11 - Ground
: Continuity should exist.
LIIA1458E
10 - 11 : Continuity should exist.
LIIA2725E

GW-90
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
Door Mirror RH (Door Mirror Defogger) Circuit CheckEIS005Z2
1. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror RH.
3. Turn ignition switch ON.
4. Check voltage between door mirror RH connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror RH connector D107 termi- nal 11 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between each door mirror RH terminals 10 and 11.
OK or NG
OK >> Repair or replace harness.
NG >> Replace door mirror RH. Refer to GW-94, "
Door Mirror
Assembly" .
Rear Window Defogger Signal CheckEIS005Z3
1. CHECK AV COMMUNICATION LINE
AV communication line check is executed. Refer to AV- 4 4 , "
Audio Communication Line Check" .
OK or NG
OK >> GO TO 2.
NG >> Replace display control unit. Refer to AV- 1 6 7 , "
DISPLAY CONTROL UNIT" .
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
D107 10 Ground Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF 0
LIIA1456E
11 - Ground
: Continuity should exist.
LIIA1458E
10 - 11 : Continuity should exist.
LIIA2725E
Is rear window defogger displayed on the display?

REAR WINDOW DEFOGGERGW-91
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
2. CHECK CAN COMMUNICATION LINE
CAN communication line check is executed. Refer to LAN-26, "
CAN COMMUNICATION" .
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> In addition, it is necessary to check CAN communication line. Refer to LAN-26, "
CAN COMMUNI-
CATION" .
Filament CheckEIS005Z4
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe.Then press the foil against the wire with your finger.
2. Attach probe circuit tester (in Volt range) to middle portion of each filament.
3. If a filament is burned out, circuit tester registers 0 or battery voltage.
4. To locate burned out point, move probe to left and right along fil- ament. Test needle will swing abruptly when probe passes the
point.
SEL122R
SEL263
SEL265

GW-92
REAR WINDOW DEFOGGER
Revision: November 20092006 QX56
Filament RepairEIS005Z5
REPAIR EQUIPMENT

Conductive silver composition (DuPont No. 4817 or equivalent)

Ruler 30 cm (11.8 in) long

Drawing pen

Heat gun

Alcohol

Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti- nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D

IDX-6
ALPHABETICAL INDEX
Magnet clutch ............................... ATC-115, ATC-176
MAIN - Wiring diagram ...................... EC-145, AT-167
Main oil pump (Transfer) ..................... TF-154, TF-167
Mainshaft (Transfer) ........................... TF-154, TF-167
Maintenance (engine)Schedule 1 ....................... MA-7
Maintenance (engine)Schedule 2 ....................... MA-9
Major overhaul (Final drive) ............................. FFD-14
Major overhaul (Transfer) ................................ TF-146
Malfunction indicator lamp (MIL) ........................ EC-63
Map lamp .......................................................... LT-135
Mass air flow sensor (MAFS) ............. EC-171, EC-180
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ....................... EC-635
MIL/DL - Wiring diagram .................................. EC-635
MIRROR - Wiring diagram ................................ GW-93
Misfire .............................................................. EC-327
Mode door control linkage adjustment ............. ATC-66
Mode door motor ............................ ATC-64, ATC-161
Model variation ................................................... GI-47
Multiport fuel injection (MFI) system .................. EC-24
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ............................................................... BL-44
N
NATS - Wiring diagram .................................... BL-140
NAVI - Wiring diagram ....................................... AV-89
NAVI Control Unit .............................................. AV-86
Navigation system ............................................. AV-84
Neutral-4LO switch ............................................ TF-62
NONDTC - Wiring diagram .............................. AT-176
NVH troubleshooting (AX) ................................. FAX-4
NVH troubleshooting (EM) ................................ EM-10
NVH troubleshooting (Final drive) ..................... RFD-7
NVH troubleshooting (Propeller shaft) ................. PR-3
NVH troubleshooting (RAX) .............................. RAX-4
NVH troubleshooting (RSU) .............................. RSU-5
NVH troubleshooting (ST) .................................... PS-5
NVH troubleshooting (Transfer) ......................... TF-10
NVH troubleshooting (WT)NVH troubleshooting (WT) .
WT-4
NVIS (Nissan vehicle immobilizer system) precautions
GI-3
O
O2H2B1 - Wiring diagram ................................ EC-165
O2H2B2 - Wiring diagram ................................ EC-167
O2S2B1 - Wiring diagram ... EC-256, EC-267, EC-280
O2S2B2 - Wiring diagram ... EC-258, EC-269, EC-282
Oil cooler (engine) ............................................. LU-11
Oil filter ............................................................... LU-10
Oil filter (Transfer) ............................................ TF-143
Oil pan (engine) ................................................ EM-24
Oil pressure (engine) ........................................... LU-7
Oil pressure relief valve (engine) ......................... LU-5
Oil pump (engine) .............................................. LU-13
Oil seal replacement (engine) ........................... EM-60
Oil seal replacement (front of final drive) FFD-8, RFD-9
Oil seal replacement (side of final drive) ......... RFD-11
On board diagnostic system ............................. EC-48
ORVR (On-board Refueling Vapor Recovery) .. EC-39
Overheat ......................................................... EC-473
P
P/SCKT - Wiring diagram ................................. WW-53
Pantograph jack .................................................. GI-41
Park/Neutral position switch ............................ EC-465
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................ EC-45
Periodic maintenance ......................................... MA-7
Personal lamp .................................................. LT-135
PGC/V - Wiring diagram ................... EC-375, EC-383
PHASE - Wiring diagram ................................ EC-349
PHONE - Wiring diagram ................................... AV-67
Pinion bearing preload diff. ............................. RFD-26
Piston pin inspection ......................................... EM-94
Piston ring inspection ........................................ EM-95
Piston to bore clearance ................................... EM-99
Planetary carrier (Transfer) ................. TF-149, TF-176
PNP/SW - Wiring diagram ... EC-467, AT-105, AT-106
POS - Wiring diagram ..................................... EC-342
POWER - Wiring diagram ................................... PG-6
Power door lock ................................................. BL-16
Power seat ......................................................... SE-83
Power steering fluid level .................................. MA-29
Power steering gear ........................................... PS-15
Power steering oil pump .................................... PS-21
Power steering pressure (PSP) sensor ........... EC-448
Power steering system bleeding .......................... PS-6
Power supply routing .......................................... PG-4
Power window .................................................. GW-15
PRE/SE - Wiring diagram ................. EC-407, EC-413
Precautions (General) ........................................... GI-4
Precautions in repairing high strength steel ..... BL-190
Pressure switch 1 ............................... AT-145, AT-159
Pressure switch 2 ............................................. AT-157
Pressure switch 3 ............................... AT-141, AT-161
Pressure switch 5 ............................... AT-149, AT-163
Pressure switch 6 ............................... AT-153, AT-165
Pressure test (A/T) ............................................. AT-52
Propeller shaft ........................................... PR-4, PR-8
Propeller shaft inspection .................................. MA-25
Propeller shaft on vehicle service ....................... PR-8
Propeller shaft vibration ............................ PR-4, PR-8
PS/SEN - Wiring diagram ............................... EC-449
R
R/VIEW - Wiring diagram .................................... DI-76
Radiator ............................................................ CO-14
Rear Audio Remote Control Unit ......................... AV-8
Rear axle ........................................................... RAX-5
Rear bumper ....................................................... EI-15
Rear case (Transfer) ........................... TF-148, TF-181

IDX-7
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
Rear combination lamp removal and installation ... LT-
125
Rear cover packing replacement diff. ..............
RFD-28
Rear door ........................................... BL-128, GW-68
Rear seat belt ...................................................... SB-6
Rear suspension ............................................. RSU-26
Rear view monitor ............................................... DI-73
Rear washer .................................................... WW-32
Rear window defogger ..................................... GW-74
Rear wiper ....................................................... WW-32
Refrigerant connection precaution .................... ATC-7
Refrigerant discharging evacuating charging ATC-171
Refrigerant general precaution .......................... ATC-6
Refrigerant lines ........... ATC-171, ATC-179, ATC-180
Refrigerant pressure sensor ............ EC-630, ATC-182
Relay box .......................................................... PG-78
Remote keyless entry system ............................ BL-44
Removal and installation (A/T) ........... AT-243, AT-246
Removal and installation (Transfer) ................. TF-145
Ring gear diff. inspection ................................. RFD-18
Road wheel size ................................................. GI-50
Rocker cover ..................................................... EM-35
Room lamp ....................................................... LT-134
Room lamp - See Interior lamp ........................ LT-134
ROOM/L - Wiring diagram ................................ LT-140
RP/SEN - Wiring diagram ............................... EC-631
S
SAE J1979 - Service $01 - 09 ........................... EC-48
SEAT - Wiring diagram ..................................... SE-83
Seat belt inspection ............................... SB-11, MA-32
Seat belt pre-tensioner .................................... SRS-57
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-6
Seat, front .......................................................... SE-91
Self-diagnosis (Transfer) .................................... TF-50
SEN/PW - Wiring diagram ............................... EC-461
SHIFT - Wiring diagram ................................... AT-222
Shift control (Transfer) ....................... TF-149, TF-176
Shift lock system .............................................. AT-221
Shock absorber (front) .................................... FSU-11
Shock absorber (rear) ..................................... RSU-35
Side air bag (satellite) sensor .......................... SRS-56
Side curtain air bag ......................................... SRS-53
Side trim .............................................................. EI-35
SMJ (super multiple junction) ............................ PG-74
SONAR - Wiring diagram .................................... DI-63
Spare tire size .................................................... GI-50
Spark plug ......................................................... EM-29
Spark plug replacement .................................... MA-18
Specification value .......................................... EC-134
Speedometer ......................................................... DI-5
Spiral cable ..................................................... SRS-48
SROOF - Wiring diagram .................................. RF-13
SRS - See Supplemental Restraint System ...... SRS-5
SRS - Wiring diagram ..................................... SRS-12
SRS Trouble diagnoses .................................... SRS-8
Stabilizer bar (front) ......................................... FSU-12
Stabilizer bar (rear) ......................................... RSU-42
Stall test (A/T) .................................................... AT-51
Standardized relay ............................................. PG-72
START - Wiring diagram ................................... SC-11
Starting system .................................................. SC-10
Steering gear, linkage and transfer gear inspection .....
MA-29
Steering linkage ................................................. PS-15
Steering wheel and column ................................. PS-7
Step lamp ......................................................... LT-135
Stop lamp ......................................................... LT-106
Stop lamp switch ................. EC-511, EC-523, EC-586
STOP/L - Wiring diagram ................................. LT-107
Strut (front) ...................................................... FSU-10
STSIG - Wiring diagram .................................. AT-101
Sub-oil pump (Transfer) ...................... TF-154, TF-167
Sun gear (Transfer) ............................ TF-149, TF-176
Sun roof, electric ................................................ RF-10
Sunload sensor .............................................. ATC-140
Sunroof .............................................................. RF-24
Supplemental Restraint System ........................ SRS-5
Supplemental restraint system - Wiring diagram . SRS-
12
Symbols and abbreviations ..................... GI-10, GI-23
Symptom matrix chart ........................................ EC-92
System readiness test (SRT) code .................... EC-54
T
Tachometer .......................................................... DI-5
Tail lamp ........................................................... LT-111
TAIL/L - Wiring diagram .................................... LT-113
TCM circuit diagram .......................................... AT-50
TCM inspection table ......................................... AT-83
TCS - Wiring diagram ..................................... BRC-16
TCS (traction control system) ........................... BRC-7
TCS component parts and connector location BRC-14
TCS wheel sensors ........................................ BRC-14
Telephone .......................................................... AV-64
Theft warning system - See Vehicle security (Theft warn-
ing) system ......................................................... BL-75
Thermometer ...................................................... DI-26
Three way catalyst ............................................. EM-21
Three way catalyst function (Bank 1) .............. EC-354
Three way catalyst function (Bank 2) .............. EC-354
Three way catalyst precautions ............................ GI-5
Throttle control motor ...................................... EC-540
Throttle control motor relay .............................. EC-528
Throttle position sensor (TPS) ... EC-198, EC-320, EC-
483, EC-485, EC-560
Throttle valve closed position learning .............. EC-78
Tie-rod ............................................................... PS-15
Timing chain ...................................................... EM-37
Tire rotation ....................................................... MA-28
Tire size .............................................................. GI-50
Torque converter installation AT-244, AT-245, AT-248,
AT-249
Torque convertor clutch solenoid valve .... AT-118, AT-
120