fuse INFINITI QX56 2006 Factory Owner's Manual

AV-52
AUDIO
Revision: November 20092006 QX56
2. CENTER SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M112 and center speaker connector M110.
2. Turn ignition switch to ACC.
3. Push the “ POWER” switch.
4. Check the signal between BOSE speaker amp. harness connec- tor M112 terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace center speaker. Refer to AV- 5 6 , "CENTER SPEAKER" .
NG >> Replace BOSE speaker amp. Refer to AV- 5 5 , "
BOSE SPEAKER AMP." .
Sound Is Not Heard From SubwooferEKS00BIP
1. CHECK FUSE
Check that the following fuse is not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect subwoofer connector.
2. Check voltage between the subwoofer and ground.
OK or NG
OK >> GO TO 3.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
Terminals
Condi-tion Reference
signal
(+) (-)
Con- nec- tor Terminal Con-
nec- tor Terminal
M112 18 M112 2 Receive
audio
signal
WKIA1223E
SKIA0177E
Unit
Terminal Signal name Fuse No.
Subwoofer 6Battery power 17
UnitTerminal No.
OFF ACC ON
(+)
(-)
Connector Terminal
Sub-
woofer B72 6 Ground Battery
voltage Battery
voltage Battery
voltage
WKIA1601E

AV-60
AUDIO ANTENNA
Revision: November 20092006 QX56
AUDIO ANTENNAPFP:28200
System DescriptionEKS00BJ1
With the ignition switch in ACC or ON, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to audio unit terminal 10.
Ground is supplied through the case of the antenna amp.
When the audio unit switch is turned ON, antenna signal is supplied

through audio unit terminal 5

to the antenna amp. terminal 1.
Then the antenna amp. is activated.
The amplified radio signals are supplied to the audio unit through the antenna amp.

AV-64
TELEPHONE
Revision: November 20092006 QX56
TELEPHONEPFP:28342
Component Parts and Harness Connector LocationEKS00GC0
WKIA4565E
1. Fuse block (J/B)2. Fuse and fusible link box 3. Fuse and relay box
4. Combination meter M24 5. AV switch
M98 6. Audio unit
M45
7. BCM M18, M19 8. Steering wheel audio control
switches 9. Microphone
R108
10. Bluetooth ON indicator R16 11. Bluetooth control unit
B141, B142
(View with seat removed)

AV-72
TELEPHONE
Revision: November 20092006 QX56
Power Supply and Ground Circuit Check for Bluetooth Control UnitEKS00GBQ
1. CHECK FUSES
Make sure the following fuses for the Bluetooth control unit are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect Bluetooth control unit connector B141.
2. Check voltage between connector terminals and ground as fol- lows.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between Bluetooth control unit and fuse.
3. CHECK GROUND CIRCUITS
1. Turn ignition switch OFF.
2. Check continuity between the following Bluetooth control unit terminals and ground.
OK or NG
OK >> Inspection End.
NG >> Repair or replace harness.
Terminals Ignition SwitchFuse No.
Connector Terminal
B141 1
All positions31
2 ACC/ON4
3 ON/START12
Terminals Ignition switch position
(+) (– )OFFACC ON
Connector Terminal
B141 1
Ground Battery
voltage Battery
voltage Battery
voltage
20 VBattery
voltage Battery
voltage
30 V0V Battery
voltage
WKIA4389E
Terminals Continuity
Connector Terminal—
B141 4
Ground Yes
21
WKIA4556E

DVD ENTERTAINMENT SYSTEMAV-75
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
DVD ENTERTAINMENT SYSTEMPFP:28184
Component Parts and Harness Connector LocationEKS00BJ5
WKIA4570E
1. Fuse block (J/B)
M4 2. Fuse and fusible link box 3. Audio Unit
M46
4. DVD player M205, M206 5. Video Monitor
R202

AV-76
DVD ENTERTAINMENT SYSTEM
Revision: November 20092006 QX56
DescriptionEKS00BJ6
Refer to Owner's Manual for DVD entertainment system operating instructions.
Power is supplied at all times

through 20A fuse (No. 31, located in the fuse and fusible link box)

to DVD player terminal 16.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to DVD player terminal 15.
Power is also supplied

from DVD player terminals 31 and 32

to video monitor terminals 11 and 12.
Ground is supplied

to DVD player terminal 22

through body grounds M57, M61 and M79.
Audio signals are supplied

through DVD player terminals 1, 2, 3 and 4

to audio unit terminals 34, 35, 36 and 37.
Video signals are supplied

through DVD player terminals 23, 24, 28 and 29

to video monitor terminals 5, 6, 7 and 8.

AV-82
DVD ENTERTAINMENT SYSTEM
Revision: November 20092006 QX56
Power Supply Circuit InspectionEKS00BJA
1. CHECK FUSES
Check that the following fuses are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect DVD player connector M205.
2. Check voltage between the DVD player and ground.
OK or NG
OK >> GO TO 3.
NG >>

Check connector housings for disconnected or loose terminals.

Repair harness or connector.
3. GROUND CIRCUIT CHECK
Check continuity between DVD player harness connector M206 ter-
minal 22 (B) and ground.
OK or NG
OK >> Inspection End.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
Unit Terminals Signal name Fuse No.
DVD player 16
Battery power 31
15 Ignition switch ACC or ON 4
UnitTerminal No.
OFF ACC ON
(+)
(-)
Connector Te r m i n a l
(wire color)
DVD player M205 16 (Y) Ground
Battery
voltage Battery
voltage Battery
voltage
15 (V) Ground 0 V Battery
voltage Battery
voltage
WKIA1197E
Continuity should exist.
WKIA1198E

NAVIGATION SYSTEMAV-87
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Component Parts LocationEKS00BJF
WKIA4571E
1. Fuse block (J/B)2. Fuse and fusible link box 3. Combination switch
M28
4. Combination meter M24 5. GPS antenna
6. Display unit
M93
7. Display control unit M94, M95 8. AV switch
M98 9. Audio unit
M45
10. Data link connector M22 11 . B C M
M18, M20 12. Steering wheel audio control switches
13. NAVI control unit B151, B152, B154 14. IPDM E/R
E121, E124

AV-126
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Power Supply and Ground Circuit Check for NAVI Control UnitEKS00GE4
1. CHECK FUSE
Make sure the following fuses of the NAVI control unit are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect NAVI control unit connector B151.
2. Check voltage between connector terminals and ground as fol- lows.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between NAVI control unit and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between the following NAVI control unit con- nector terminals and ground.
OK or NG
OK >> Inspection End.
NG >> Repair or replace harness.
Terminals Power source Fuse No.
Connector Terminal
B151 2
Battery power 31
5 ACC/ON power 4
TerminalsIgnition switch position
(+) (– )OFFACCON
Connector Terminal
B151 2
Ground Battery
voltage Battery
voltage Battery
voltage
50 VBattery
voltage Battery
voltage
WKIA4601E
Terminals Ignition switch Continuity
Connector Terminal—
B151 1Ground OFF Yes
WKIA4207E

NAVIGATION SYSTEMAV-127
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Power Supply and Ground Circuit Check for Display Control UnitEKS00GE5
1. CHECK FUSE
Make sure the following fuses of the display control unit are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect display control unit connector M94.
2. Check voltage between connector terminals and ground as fol- lows.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between display control unit and fuse.
3. CHECK GROUND CIRCUIT
Check continuity between the following display control unit connec-
tor terminals and ground.
OK or NG
OK >> Inspection End.
NG >> Repair or replace harness.
Terminals Power source Fuse No.
Connector Terminal
M94 1
Battery power 31
10 ACC power4
Terminals Ignition switch position
(+) (– )OFFACC ON
Connector Terminal
M94 1
Ground Battery
voltage Battery
voltage Battery
voltage
10 0VBattery
voltage Battery
voltage
WKIA1373E
Terminals Ignition switch Continuity
Connector Terminal—
M94 3Ground OFF Yes
SKIA4293E