light INFINITI QX56 2006 Factory Owner's Manual

AV-34
AUDIO
Revision: November 20092006 QX56
Occurrence conditionPossible cause
Occurs only when engine is ON. A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.

Ignition components
A whistling noise occurs while the engine speed is
high. A booming noise occurs while the engine is
running and the lighting switch is ON.

Generator
The occurrence of the noise is linked with the operation of the fuel pump.

Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating. A cracking or snapping sound occurs with the
operation of various switches.

Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing.

Motor case ground

Motor
The noise occurs constantly, not just under certain conditions.

Rear defogger coil malfunction

Open circuit in printed heater

Poor ground of antenna amplifier or
antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.

Ground wire of body parts

Ground due to improper part installation

Wiring connections or a short circuit

NAVIGATION SYSTEMAV-101
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
61 (R/L) GroundIllumination
signal Input ON Lighting switch in
1st position Battery voltage
Display unit illu-
mination does
not change
when lighting
switch is turned
to 1st position.-
Lighting switch is
OFF 3V or less
63 (G/R) Ground Ignition signal Input ON –Battery voltage Navigation cur-
rent location
mark does not
indicate the cor-
rect position.
65 (G/W) Ground Reverse
signal Input ON A/T selector lever in
R position Battery voltage
The navigation
current-location
mark moves
strangely when
the vehicle is
moving back-
wards.
A/T selector lever
not in R position 0V
66 (W/R) Ground Ve h ic l e
speed signal
(8-pulse) Input ON
When vehicle speed
is approx. 40 km/h
(25 MPH) Navigation cur-
rent location
mark does not
indicate the cor-
rect position.
68 –Shield
ground –– –
––
69 (L) Ground Communica-
tion signal (+) Input/
output ON
– System does not
work properly.
70 (P) Ground Communica-
tion signal ( –) Input/
output ON
– System does not
work properly.
73 74 GPS signal Input ON Connector is not
connected. 5VNavigation sys-
tem GPS correc-
tion is not
possible.
Terminal No.
(Wire color)
ItemSignal
input/
output Condition
Voltage
(Approx.) Example of
symptom
+ – Igni-
tion
switch Operation
PKIA1935E
SKIA0175E
SKIA0176E

AV-102
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Terminals and Reference Value for Display Control unitEKS00BJL
Terminal No.
(Wire color)
ItemSignal
input/
output Condition
Voltag e
(Approx.) Example of
symptom
+ – Igni-
tion
switch Operation
1 (Y) Ground Battery
Power Input OFF
–Battery voltage System does not
work properly.
2 (L/W) Ground Power Sup-
ply (Inverter) Output ON
–9 VScreen is not
shown.
3 (B) Ground Ground –ON – 0 V –
4 (L/R) Ground Power Sup-
ply (Signal) Output ON
–9 VScreen is not
shown.
5 (P) Ground (Inverter)
Ground –
ON – 0 V –
6 (GR) Ground Reverse
signal Input ON Selector lever in R
position Battery voltage
Impossible to
gain direction of
vehicle.
Selector lever not in
R position 0 V
7 (P/L) Ground (Signal)
Ground –
ON – 0 V –
10 (O) Ground ACC signal Input ACC –Battery voltage System does not
work properly.
12 (G/R) Ground Ignition signal Input ON –Battery voltage Vehicle informa-
tion setting is not
possible.
13 (B) Ground Ground –ON – 0 V –
14 (R/L) Ground Illumination
signal Input OFF Lighting switch posi-
tion 1st or 2nd Battery voltageDisplay unit
does not change
when lighting
switch is turned
to 1st position.
Lighting switch posi-
tion OFF 0 V
16 (W/R) Ground Vehicle
speed signal
(8 –pulse) Input ON
When vehicle speed
is approx. 40 km/h
(25 MPH) Value of vehicle
speed informa-
tion is not accu-
rately displayed.
25 (L) –CAN-H –– – ––
26 (P) –CAN-L –– – ––
28 (V) Ground Communica-
tion signal (+) Input/
Output ON
– System does not
work properly.
29 –Shield
ground –– –
––
SKIA0168E
SKIA0175E

AV-108
NAVIGATION SYSTEM
Revision: November 20092006 QX56
Terminals and Reference Value for AV SwitchEKS00BJN
Terminal No.
(Wire color) ItemSignal
input/
output Condition
Voltage
(Approx.) Example of
symptom
+ – Ignition
switch Operation
1 (Y) Ground Battery
power Input OFF
-Battery voltage System does not
work properly.
2 (V) Ground ACC signal Input ACC -Battery voltage System does not
work properly.
3 (R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (position 1).
Battery voltageAV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1).
Turn lighting switch
OFF.
3.0V or less
4 (BR) Ground Illumination
control signal Input ON Illumination control
switch is operated
by lighting switch in
1st position. Changes between 0 and 12V.
AV switch illumi-
nation cannot be
controlled.
5 (B) Ground Ground - ON -0V -
6 (V) Ground Communica-
tion signal (+) Input/
output ON
- System does not
work properly.
7- Shield
ground -- -
--
8 (LG) Ground Communica-
tion signal (-) Input/
output ON
- System does not
work properly.
12 (R) Ground Remote con-
trol A Input ON Press MODE
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK UP
switch 0.75V
Press VOL UP switch 2V
Except for above 5V
13 (G) Ground Remote con-
trol B Input ON Press POWER
switch 0V
Steering wheel
audio controls
do not function.
Press SEEK
DOWN switch 0.75V
Press VOL DOWN switch 2V
Except for above 5V
14 (L) - Remote con-
trol ground -- -
-Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E

NAVIGATION SYSTEMAV-109
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
Terminals and Reference Value for BCMEKS00BJO
Te r m i n a l
No. Wire
color Signal name Measuring condition
Reference value
(Approx.)
Ignition
switch Operation or condition
2 SB Combination switch input 5 ONLighting, turn, wiper OFF
Wiper dial position 4
3 G/Y Combination switch input 4 ONLighting, turn, wiper OFF
Wiper dial position 4
4 Y Combination switch input 3 ONLighting, turn, wiper OFF
Wiper dial position 4
5 G/B Combination switch input 2 ONLighting, turn, wiper OFF
Wiper dial position 4
6 V Combination switch input 1
11 O Ignition switch (ACC) ACC— Battery voltage
32 R/G Combination switch output 5 ON Lighting, turn, wiper OFF
Wiper dial position 4
33 R/Y Combination switch output 4 ON Lighting, turn, wiper OFF
Wiper dial position 4
34 L Combination switch output 3 ON Lighting, turn, wiper OFF
Wiper dial position 4
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
SKIA5291E

AV-110
NAVIGATION SYSTEM
Revision: November 20092006 QX56
35 O/B Combination switch output 2
ONLighting, turn, wiper OFF
Wiper dial position 4
36 R/W Combination switch output 1
38 W/L Ignition switch (ON) ON— Battery voltage
39 L CAN-H —— —
40 P CAN-L —— —
57 Y/R Battery power supply OFF— Battery voltage
67 B Ground ON— 0V
70 W/B Battery power supply (fusible link) OFF —Battery voltage
Terminal
No. Wire
color Signal name Measuring condition
Reference value
(Approx.)
Ignition
switch Operation or condition
SKIA5292E

NAVIGATION SYSTEMAV-111
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
On Board Self-Diagnosis FunctionEKS00BJP
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.

CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
ModeDescription
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)

NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.

Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENT Display diagnosis
In display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signals In display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE , ignition switch signal, and reverse sig-
nal.
Auto Climate Control A/C self-diagnosis of A/C system.
Navigation Display diagnosis
In NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signals In NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of Errors Diagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tion Display Lon-
gitude & Lat-
itude
Display the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
bration Under ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustment Corrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
Location This mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.

AV-118
NAVIGATION SYSTEM
Revision: November 20092006 QX56
DISPLAY DIAGNOSIS

When RGB signal error occurred in the RGB system, tone of the color bar will change as follows.

When the color of the screen looks unusual, refer to AV- 1 4 6 , "Color of RGB Image is Not Proper (All
Screens Look Bluish)" , AV- 1 4 7 , "Color of RGB Image is Not Proper (All Screens Look Reddish)" and
AV- 1 4 8 , "
Color of RGB Image is Not Proper (All Screens Look Yellowish)" .
VEHICLE SIGNALS

A comparison check can be made of each actual vehicle signal
and the signals recognized by the system.
CAUTION:
In case of confirming light signal, set D/N mode to ON/OFF
of lighting switch (normal setting).

OFF: D (Day mode)

ON: N (Night mode)
Unless above setting, light signal (ON/OFF) may not be
accurately displayed.
WKIA4316E
R (red) signal error : Screen looks bluish
G (green) signal error : Screen looks reddish
B (blue) signal error : Screen looks yellowish
WKIA4306E
Diagnosis item Display Condition Remarks
Vehicle speed ON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed by
approx. 1.5 seconds. This is normal.
OFF Vehicle speed = 0 km/h (0 MPH)
– Ignition switch in ACC position
Light ON Lighting switch ON
–
OFF Lighting switch OFF
IGN ON Ignition switch ON
–
OFF Ignition switch ACC
Reverse ON Selector lever in R position
Changes in indication may be delayed by
approx. 1.5 seconds. This is normal.
OFF Selector lever in other than R position
– Ignition switch in ACC position

NAVIGATION SYSTEMAV-119
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56

If vehicle speed is NG, refer to AV- 1 3 2 , "Vehicle Speed Signal Check for Display Control Unit" .

If light is NG, refer to AV- 1 3 3 , "Illumination Signal Check for Display Control Unit" .

If IGN is NG, refer to AV- 1 3 4 , "Ignition Signal Check for Display Control Unit" .

If reverse is NG, refer to AV- 1 3 4 , "Reverse Signal Check for Display Control Unit" .
NAVIGATION
1. The initial confirmation/adjustment screen will be shown, and
items “Display Diagnosis”, “Vehicle Signals”, “Navigation ”,
"Error History “ and "Delete Unit Connection Log ” will become
selective.
2. Select each switch on “CONFIRMATION/ADJUSTMENT ”
screen to display the relevant diagnosis screen.
DISPLAY DIAGNOSIS

When RGB signal error occurred in the RGB system, tone of the color bar will change as follows.

When the color of the screen looks unusual, refer to AV- 1 4 3 , "Color of RGB Image is Not Proper (Only
NAVI Screen Looks Bluish)" , AV- 1 4 4 , "Color of RGB Image is Not Proper (Only NAVI Screen Looks Red-
dish)" and AV- 1 4 5 , "Color of RGB Image is Not Proper (Only NAVI Screen Looks Yellowish)" .
WKIA4311E
WKIA4317E
R (red) signal error : Screen looks bluish
G (green) signal error : Screen looks reddish
B (blue) signal error : Screen looks yellowish

AV-120
NAVIGATION SYSTEM
Revision: November 20092006 QX56
VEHICLE SIGNALS

A comparison check can be made of each actual vehicle signal
and the signals recognized by the system.
CAUTION:
In case of confirming light signal, set D/N mode to ON/OFF
of light switch (normal setting).

OFF: D (Day mode)

ON: N (Night mode)
Unless mode is in above setting, light signal (ON/OFF) may
not be accurately displayed.

If vehicle speed is NG, refer to AV- 1 3 1 , "Vehicle Speed Signal Check for NAVI Control Unit" .

If light is NG, refer to AV- 1 3 3 , "Illumination Signal Check for NAVI Control Unit" .

If IGN is NG, refer to AV- 1 3 3 , "Ignition Signal Check for NAVI Control Unit" .

If reverse is NG, refer to AV- 1 3 4 , "Reverse Signal Check for NAVI Control Unit" .
ERROR HISTORY
DIAGNOSIS BY ERROR HISTORY
The “Self-diagnosis ” results indicate whether an error occurred during the period from when the ignition switch
is turned to ON until “Self-diagnosis” is completed.
WKIA4443E
Diagnosis item Display Condition Remarks
Vehicle speed ON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed by
approx. 1.5 seconds. This is normal.
OFF Vehicle speed = 0 km/h (0 MPH)
– Ignition switch in ACC position
Lights ON Lighting switch ON
–
OFF Lighting switch OFF
Ignition ON Ignition switch ON
–
OFF Ignition switch ACC
Reverse ON Selector lever in R position
Changes in indication may be delayed by
approx. 1.5 seconds. This is normal.
OFF Selector lever in other than R position
– Ignition switch in ACC position
WKIA4444E