Brake booster INFINITI QX56 2008 Factory User Guide

BR-26
< ON-VEHICLE REPAIR >
BRAKE BOOSTER
BRAKE BOOSTER
Removal and InstallationINFOID:0000000004894511
CAUTION:
• Be careful not to deform or bend brake piping while removing and installing brake booster.
• Replace clevis pin if it is damaged.
• Be careful not to damage brake booster stud bolt threads. If brake booster is tilted or inclined during
installation, dash panel may damage the threads.
• Attach the check valve in the correct direction.
REMOVAL
1. Remove air duct and resonator assembly. Refer to EM-25, "Removal and Installation".
2. Remove cowl top assembly. Refer to EXT-18, "
Removal and Installation".
3. Remove master cylinder assembly from brake booster. Refer to BR-25, "
Removal and Installation".
4. Remove vacuum hose from brake booster. Refer to BR-28, "
Removal and Installation".
5. Disconnect active booster and delta stroke s ensor harness connectors from brake booster.
6. Remove the instrument lower panel LH. Refer to IP-11, "
Exploded View".
7. Remove brake pedal to clevis attachment snap pin and clevis pin from inside the vehicle.
8. Remove brake booster to brake pedal assembly nuts.
9. Reposition the A/C line out of the way.
10. Remove brake booster and spacer from dash panel.
INSPECTION AFTER REMOVAL
Output Rod Length Inspection
1. Reservoir tank 2. Master cylinder assembly3. Gasket
4. Brake pedal 5. Lock nut 6. Spacer block
7. Brake booster 8. Active booster9. Delta stroke sensor
AWFIA0416GB
Revision: March 2010 2008 QX56

BRAKE BOOSTERBR-27
< ON-VEHICLE REPAIR >
C
DE
G H
I
J
K L
M A
B
BR
N
O P
1. Using a hand vacuum pump, apply a vacuum of – 66.7 kPa (– 500 mmHg, –19.69 inHg) to brake booster.
2. Check output rod length.
INSTALLATION
1. Loosen lock nut to adjust input r od length so that the length (B)
is set at the specified value.
2. After adjusting length (B), temporarily tighten lock nut and install brake booster and spacer block.
• Install the gaskets and spacer block between brake boosterand dash panel.
3. Connect brake pedal to clevis on the input rod.
4. Install brake booster to brake pedal assembly nuts and tighten to the specified torque.
5. Connect active booster and delta stroke s ensor harness connectors to brake booster.
6. Connect vacuum hose to brake booster.
7. Install master cylinder assembly to brake booster. Refer to BR-25, "
Removal and Installation".
8. Adjust the height and play of brake pedal. Refer to BR-15, "
Inspection and Adjustment".
9. Tighten lock nut of input rod to specification.
10. Install the instrument lower panel LH. Refer to IP-11, "
Exploded View".
11. Secure A/C line into clips.
12. Install cowl top assembly. Refer to EXT-18, "
Removal and Installation".
13. Install air duct and resonator assembly. Refer to EM-25, "
Removal and Installation".
14. Refill with new brake fluid and bleed air. Refer to BR-17, "
Bleeding Brake System".
Output rod length : Refer to
BR-46, "
Brake
Booster".
SBR208E
Input rod length (B) : Refer to BR-46, "Brake
Booster".
WFIA0382E
Revision: March 2010 2008 QX56

BR-28
< ON-VEHICLE REPAIR >
VACUUM LINES
VACUUM LINES
Removal and InstallationINFOID:0000000004894512
REMOVAL
1. Remove engine room cover. Refer to EM-24, "Removal and Installation"
2. Disconnect vacuum hose from hose clip.
3. Release clamps and disconnect vacuum hose.
4. Remove check valve from brake booster.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Insert vacuum hose for at least 24 mm (0.94 in).
• Do not use lubricating oil during assembly.
1. Hose clip2. Clamp3. Vacuum hose
4. Check valve
LFIA0216E
SBR225B
Revision: March 2010 2008 QX56

SERVICE DATA AND SPECIFICATIONS (SDS)BR-45
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
DE
G H
I
J
K L
M A
B
BR
N
O P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000004894499
Unit: mm (in)
Brake PedalINFOID:0000000004894500
Unit: mm (in)
CAUTION:
When equipped with adjustable pedal, the pedal must be in the forward most position (closest to the floor) for pedal height
adjustment. Front brake Brake model
AD41VA
Rotor outer diameter × thickness 350 x 30 (13.78 x 1.181)
Pad Length × width × thickness 151.6 x 56.5 x 12.0 (5.97 x 2.22 x 0.476)
Cylinder bore diameter 50.8 (2.00)
Rear brake Brake model AD14VE
Rotor outer diameter × thickness 320 x 14 (12.60 x 0.551)
Pad Length × width × thickness 83.0 x 33.0 x 12.0 (3.268 x 1.299 x 0.472)
Cylinder bore diameter 48 (1.89)
Control valve Valve model Electric brake force distribution
Brake booster Booster model C215T
Diaphragm diameter 215 (8.46)
Recommended brake fluid Refer to MA-12, "
Fluids and Lubricants".
Pedal free height (H) with pedal in forward most position 182.3 - 192.3 (7.18 - 7.57)
Pedal travel (T) 153.3 (6.04)
Stop lamp switch and ASCD cancel switch threaded end to brake pedal bracket gap 0.74 - 1.96 (0.029 - 0.077)
ALFIA0149ZZ
Revision: March 2010 2008 QX56

BR-46
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Brake Booster
INFOID:0000000004894501
Unit: mm (in)
Check ValveINFOID:0000000004894502
Front Disc BrakeINFOID:0000000004894503
Unit: mm (in)
Rear Disc BrakeINFOID:0000000004894504
Unit: mm (in)
Output rod length [at -66.7 kPa (-500 mmHg, -19.69 inHg) vacuum] 15.6 - 15.9 (0.614 - 0.626)
Input rod installation length (B) 151 (5.94)
SBR208E
WFIA0382E
Vacuum leakage
[at vacuum of – 66.7 kPa(– 500 mmHg, – 19.69 inHg)]Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake model
AD41VA
Brake pad Standard thickness (new)
12.0 (0.476)
Repair limit thickness 1.0 (0.039)
Disc rotor Standard thickness (new)
30 (1.181)
Repair limit thickness 28 (1.102)
Maximum uneven wear (measured at 8 positions) 0.015 (0.0006)
Runout limit (with it attached to the vehicle) 0.03 (0.001)
Brake model AD14VE
Brake pad Standard thickness (new)
12.0 (0.472)
Repair limit thickness 1.0 (0.039)
Revision: March 2010 2008 QX56

BRC-2
C1110, C1170 ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT) ...........................
37
DTC Logic ...............................................................37
Diagnosis Procedure ..............................................37
Special Repair Requirement ...................................37
C1111 ABS MOTOR, MOTOR RELAY SYS-
TEM ................................................................. ...
38
Description ........................................................... ...38
DTC Logic ...............................................................38
Diagnosis Procedure ..............................................38
Component Inspection ............................................39
Special Repair Requirement ...................................39
C1113, C1145, C1146 YAW RATE/SIDE/DE-
CEL G SENSOR ............................................. ...
40
Description ........................................................... ...40
DTC Logic ...............................................................40
Diagnosis Procedure ..............................................40
Component Inspection ............................................41
Special Repair Requirement ...................................41
C1115 WHEEL SENSOR ................................ ...43
Description ........................................................... ...43
DTC Logic ...............................................................43
Diagnosis Procedure ..............................................43
Component Inspection ............................................44
Special Repair Requirement ...................................45
C1116 STOP LAMP SWITCH ......................... ...46
Description ........................................................... ...46
DTC Logic ...............................................................46
Diagnosis Procedure ..............................................46
Special Repair Requirement ...................................47
C1120, C1122, C1124, C1126 IN ABS SOL .....48
Description ........................................................... ...48
DTC Logic ...............................................................48
Diagnosis Procedure ..............................................48
Component Inspection ............................................49
Special Repair Requirement ...................................50
C1121, C1123, C1125, C1127 OUT ABS SOL ...51
Description ........................................................... ...51
DTC Logic ...............................................................51
Diagnosis Procedure ..............................................51
Component Inspection ............................................52
Special Repair Requirement ...................................53
C1130, C1131, C1132, C1133, C1136 EN-
GINE SIGNAL ................................................. ...
54
Description ........................................................... ...54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
Special Repair Requirement ...................................54
C1140 ACTUATOR RLY ................................ ...56
Description ........................................................... ...56
DTC Logic ...............................................................56
Diagnosis Procedure ..............................................56
Component Inspection ......................................... ...57
Special Repair Requirement ...................................57
C1142 PRESS SENSOR ...................................58
Description ........................................................... ...58
DTC Logic ...............................................................58
Diagnosis Procedure ...............................................58
Component Inspection ............................................60
Special Repair Requirement ...................................60
C1143, C1144 STEERING ANGLE SENSOR ...61
Description ..............................................................61
DTC Logic ...............................................................61
Diagnosis Procedure ...............................................61
Component Inspection ............................................62
Special Repair Requirement ...................................62
C1155 BRAKE FLUID LEVEL SWITCH ...........64
Description ........................................................... ...64
DTC Logic ...............................................................64
Diagnosis Procedure ...............................................64
Component Inspection ............................................65
Special Repair Requirement ...................................65
C1156 ST ANG SEN COM CIR .........................67
Description ..............................................................67
DTC Logic ...............................................................67
Diagnosis Procedure ...............................................67
C1160 DECEL G SEN SET ...............................68
Description ..............................................................68
DTC Logic ...............................................................68
Diagnosis Procedure ...............................................68
C1163 ST ANGLE SEN SAFE ..........................69
Description ........................................................... ...69
DTC Logic ...............................................................69
Diagnosis Procedure ...............................................69
C1164, C1165, C1166, C1167 CV/SV SYS-
TEM ....................................................................
70
Description ........................................................... ...70
DTC Logic ...............................................................70
Diagnosis Procedure ...............................................70
Component Inspection ............................................71
Special Repair Requirement ...................................72
C1178, C1181, C1184, C1189 ABS ACTIVE
BOOSTER .........................................................
73
Description ........................................................... ...73
DTC Logic ...............................................................73
Diagnosis Procedure ...............................................73
Component Inspection ............................................74
Special Repair Requirement ...................................75
C1179 ABS DELTA S SEN NG .........................76
Description ........................................................... ...76
DTC Logic ...............................................................76
Diagnosis Procedure ...............................................76
Component Inspection ............................................77
Special Repair Requirement ...................................77
Revision: March 2010 2008 QX56

VDC
BRC-13
< FUNCTION DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Component Parts LocationINFOID:0000000001686241
1. Front wheel sensor LH E18 Front wheel sensor RH E117 2. Delta stroke sensor E114 3. Brake fluid level switch E21
4. Active booster E49 5. Front pressure sensor E31 6. Rear pressure sensor E32
7. ABS actuator and electric unit (con- trol unit) E125 8. Stop lamp switch E38
9. Combination meter M23, M24
AWFIA0713GB
Revision: March 2010 2008 QX56

BRC-14
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
VDC
Component Description
INFOID:0000000001686242
10. Yaw rate/side/decel G sensor M108 11. Rear wheel sensor LH C11 Rear wheel sensor RH C10 12. Steering angle sensor M17
13. VDC OFF switch M253 14. Stop lamp relay E12
Component parts Reference
ABS actuator and electric unit (control unit) Pump
BRC-38, "
Description"Motor
Actuator relayBRC-56, "
Description"
Solenoid valveBRC-48, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)BRC-70, "Description"
Wheel sensor
BRC-29, "Description"
Yaw rate/side/decel G sensorBRC-40, "Description"
Steering angle sensorBRC-61, "Description"
VDC OFF switchBRC-81, "Description"
ABS warning lampBRC-83, "Description"
Brake warning lampBRC-84, "Description"
VDC OFF indicator lampBRC-85, "Description"
SLIP indicator lampBRC-86, "Description"
Front pressure sensor
BRC-58, "Description"Rear pressure sensor
Active boosterBRC-73, "
Description"
Delta stroke sensorBRC-76, "Description"
Revision: March 2010 2008 QX56

BRC-16
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
TCS
Component Parts Location
INFOID:0000000001691093
1. Front wheel sensor LH E18 Front wheel sensor RH E117 2. Delta stroke sensor E114
3. Brake fluid level switch E21
4. Active booster E49 5. Front pressure sensor E316. Rear pressure sensor E32
7. ABS actuator and el ectric unit (con-
trol unit) E125 8. Stop lamp switch E38
9. Combination meter M23, M24
AWFIA0713GB
Revision: March 2010 2008 QX56

TCS
BRC-17
< FUNCTION DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Component DescriptionINFOID:0000000001691094
10. Yaw rate/side/decel G sensor M108 11. Rear wheel sensor LH C11 Rear wheel sensor RH C1012. Steering angle sensor M17
13. VDC OFF switch M253 14. Stop lamp relay E12
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-38, "
Description"Motor
Actuator relayBRC-56, "
Description"
Solenoid valveBRC-48, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)BRC-70, "Description"
Wheel sensor
BRC-29, "Description"
Yaw rate/side/decel G sensorBRC-40, "Description"
Steering angle sensorBRC-61, "Description"
VDC OFF switchBRC-81, "Description"
ABS warning lampBRC-83, "Description"
Brake warning lampBRC-84, "Description"
VDC OFF indicator lampBRC-85, "Description"
SLIP indicator lampBRC-86, "Description"
Front pressure sensor
BRC-58, "Description"Rear pressure sensor
Active boosterBRC-73, "
Description"
Delta stroke sensorBRC-76, "Description"
Revision: March 2010 2008 QX56