fuel cap release ISUZU AXIOM 2002 Service Repair Manual

6E±58
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS

For the 3.5L w/automatic transmission, the
pre-catalyst sensors are designated Bank 1 HO2S 1
and Bank 2 HO2S 1. The post-catalyst sensors are
Bank 1 HO2S 2 and Bank 2 HO2S 2.
Catalyst Monitor Outputs
The catalyst monitor diagnostic is sensitive to the
following conditions:

Exhaust leaks

HO2S contamination

Alternate fuels
Exhaust system leaks may cause the following:

Preventing a degraded catalyst from failing the
diagnostic.

Causing a false failure for a normally functioning
catalyst.

Preventing the diagnostic from running.
Some of the contaminants that may be encountered are
phosphorus, lead, silica, and sulfur. The presence of
these contaminants will prevent the TWC diagnostic from
functioning properly.
Three-Way Catalyst Oxygen Storage Capacity
The Three-Way catalyst (TWC) must be monitored for
efficiency. To accomplish this, the control module
monitors the pre-catalyst HO2S and post-catalyst HO2S
oxygen sensors. When the TWC is operating properly,
the post-catalyst oxygen sensor will have significantly
less activity than the pre-catalyst oxygen sensor. The
TWC stores and releases oxygen as needed during its
normal reduction and oxidation process. The control
module will calculate the oxygen storage capacity using
the difference between the pre-catalyst and post catalyst
oxygen sensor's voltage levels. If the activity of the
post-catalyst oxygen sensor approaches that of the
pre-catalyst oxygen sensor, the catalyst's efficiency is
degraded.
Stepped or staged testing level allow the control module
to statistically filter test information. This prevents falsely
passing or falsely failing the oxygen storage capacity test.
The calculations performed by the on-board diagnostic
system are very complex. For this reason, post catalyst
oxygen sensor activity should not be used to determine
oxygen storage capacity unless directed by the service
manual.
Two stages are used to monitor catalyst efficiency.
Failure of the first stage will indicate that the catalyst
requires further testing to determine catalyst efficiency.
The seconds stage then looks at the inputs for the pre and
post catalyst HO2S sensors more closely before
determining if the catalyst is indeed degraded. This
further statistical processing is done to increase the
accuracy of oxygen storage capacity type monitoring.
Failing the first (stage 1) test DOES NOT indicate a failed
catalyst. The catalyst may be marginal or the fuel sulfur
content could be very high.Aftermarket HO2S characteristics may be different from
the original equipment manufacturer sensor. This may
lead to a false pass or a false fail of the catalyst monitor
diagnostic. Similarly, if an aftermarket catalyst does not
contain the same amount of cerium as the original part,
the correlation between oxygen storage and conversion
efficiency may be altered enough to set a false DTC.
Misfire Monitor Diagnostic Operation
Misfire Monitor Diagnostic Operation
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
The misfire ratio is calculated once every 100 engine
cycles. For example, on a 6-cylinder engine, 600 ignition
plug sparks occur every 100 cycles and if a misfire occurs
12 times during that time, the misfire is 12/600 y 100 = 2
%.
Misfire Counters
Whenever a cylinder misfires, the misfire diagnostic
counts the misfire and notes the crankshaft position at the
time the misfire occurred. These ªmisfire countersº are
basically a file on each engine cylinder. A current and a
history misfire counter are maintained for each cylinder.
The misfire current counters (Misfire Cur #1-6) indicate
the number of firing events out of the last 100 cylinder
firing events which were misfires. The misfire current
counter will display real time data without a misfire DTC
stored. The misfire history counters (Misfire Hist #1-6)
indicate the total number of cylinder firing events which
were misfires. The misfire history counters will display 0
until the misfire diagnostic has failed and a DTC P0300 is
set. Once the misfire DTC P0300 is set, the misfire
history counters will be updated every 100 cylinder firing
events. A misfire counter is maintained for each cylinder.
If the misfire diagnostic reports a failure, the diagnostic
executive reviews all of the misfire counters before
reporting DTC. This way, the diagnostic executive
reports the most current information.
When crankshaft rotation is erratic, a misfire condition will
be detected. Because of this erratic condition, the data
that is collected by the diagnostic can sometimes
incorrectly identify which cylinder is misfiring. Misfires are
counted from more than one cylinder. Cylinder #1 has the
majority of counted misfires. In this case, the Misfire
Counters would identify cylinder #1 as the misfiring
cylinder. The misfires in the other counters were just
background noise caused by the erratic misfire rotation of
the crankshaft. If the number of accumulated misfires is
sufficient for the diagnostic to identify a true misfire, the
diagnostic will set DTC P0300 ± Misfire Detected.
Use diagnostic equipment to monitor misfire counter data
on OBD II-compliant vehicles. Knowing which specific
cylinder(s) misfired can lead to the root cause, even when
dealing with a multiple cylinder misfire. Using the
information in the misfire counters, identify which
cylinders are misfiring. If the counter indicate cylinders

6E±108
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Circuit Description
When the ignition switch is first turned ªONº, the
powertrain control module (PCM) energizes the fuel
pump relay which applies power to the in-tank fuel pump.
The fuel pump relay will remain ªONº as long as the
engine is running or cranking and the PCM is receiving
58X crankshaft position pulses. If no 58X crankshaft
position pulses are present, the PCM de-energizes the
fuel pump relay within 2 seconds after the ignition is
turned ªONº or the engine is stopped.
The fuel pump delivers fuel to the fuel rail and injectors,
then to the fuel pressure regulator. The fuel pressure
regulator controls fuel pressure by allowing excess fuel to
be returned to the fuel tank. With the engine stopped and
ignition ªONº, the fuel pump can be turned ªONº by using a
command by the Tech 2.
Diagnostic Aids
An intermittent may be caused by a poor connection,
rubbed-through wire insulation, or a wire broken inside
the insulation. Check for the following items:

Poor connection or damaged harness ± Inspect the
PCM harness and connectors for improper mating,
broken locks, improperly formed or damaged
terminals, poor terminal-to-wire connection, and
damaged harness.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart.
2. If the fuel pump is operating but incorrect pressure is
noted, the fuel pump wiring is OK and the ªFuel
System Pressure Testº chart should be used for
diagnosis.
CAUTION: To reduce the risk of fire and personal
injury:

It is necessary to relieve fuel system pressure
before connecting a fuel pressure gauge. Refer to
Fuel Pressure Relief Procedure, below.

A small amount of fuel may be released when
disconnecting the fuel lines. Cover fuel line
fittings with a shop towel before disconnecting, to
catch any fuel that may leak out. Place the towel in
an approved container when the procedure is
completed.
Fuel Pressure Relief Procedure
1. Remove the fuel cap.
2. Remove the fuel pump relay from the underhood
relay center.
3. Start the engine and allow it to stall.
4. Crank the engine for an additional 3 seconds.
Fuel Gauge Installation
1. Remove the shoulder fitting cap.
2. Install fuel gauge J 34730-1 to the fuel feed line
located in front of and above the right side valve train
cover .
3. Reinstall the fuel pump relay.

6E±319
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Engine speed is less than 1200 RPM.

Above conditions are present for 60 to 180 seconds.
Action Taken When the DTC Sets

The PCM will ON the MIL after second trip with
detected the fault.

The PCM will store conditions which were present
when the DTC set as Freeze Frame and in the Failure
Records data.
Conditions for Clearing the MIL/DTC

The PCM will turn the MIL ªOFFº when the diagnostic
has been run and the fault condition is no longer
present.

A history DTC P0440 will clear after 40 consecutive
warm-up cycles have occurred without a fault.

DTC P0440 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:

Cracked or punctured EVAP canister.

Damaged or disconnected source vacuum line, EVAP
purge line, vent hose or fuel tank vapor line.

Poor connection at PCM ± Inspect harness connectors
for backed-out terminals, improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal to wire connection.

Damaged harness±Inspect the wiring harness to the
EVAP canister vent solenoid, EVAP canister purge
solenoid and the fuel tank pressure sensor for an
intermittent open or short circuit.

Kinked, pinched, or plugged vacuum source, EVAP
purge, or fuel tank vapor line±Verify that the lines are
not restricted.Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how often
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart.
2. If an EVAP canister vent solenoid or an EVAP
canister purge solenoid electrical fault is present,
the purge system will not operate correctly.
Repairing the electrical fault will very likely correct
the condition that set DTC P0440.
3. Checks the fuel tank pressure sensor at ambient
pressure.
4. Determines whether or not the EVAP system can be
sealed sufficiently to be pressurized. If not, the
large leak must be located and corrected before
continuing with diagnosis.
5. Verifies that the fuel tank pressure sensor accurately
reacts to EVAP system pressure changes.
8. Checks for a blocked EVAP canister purge solenoid.
The PCM commands the EVAP canister purge
solenoid ªOFFº (open) and the vent solenoid ªONº
(closed) with the Tech 2 ªSystem Perfº, EVAP
output control function activated. Any pressure in
the system should be released through the EVAP
canister purge solenoid within a few seconds when
ªSystem Perfº, is activated.
9. Ensures that sufficient source vacuum is present at
the EVAP canister purge solenoid.
DTC P0440 ± EVAP System

StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
2Is DTC P0452 or P0453 also set?
Ð
Go to other
DTC first
Go to Step 3
31. Ignition ªOFFº.
2. Remove the fuel cap.
3. Ignition ªONº.
4. Observe ªFuel Tank Pressureº on the Tech 2.
Does the Tech 2 indicate ªFuel Tank Pressureº at the
specified value?
1.51 VGo to Step 4
Go to DTC
P0452
or
DTC P0453
41. Replace the fuel cap.
2. Engine is running.
3. Observe ªFuel Tank Vacuumº on the Tech 2.
Does Tech 2 indicate ªFuel Tank Vacuumº at the
specified value?
1.47±1.51 VGo to Step 7Go to Step 6

6E±555
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
6. Install the fuel rail. Refer to Fuel Rail section.
014RW164
7. Install the common chamber. Refer to Common
Chamber in Engine Mechanical
section.
8. Install the engine cover.
9. Connect the negative battery cable.
Fuel Metering System
Fuel Pressure Relief Procedure
CAUTION: To reduce the risk of fire and personal
injury, there are necessary to relieve the fuel system
pressure before filler and gauge unit servicing the
fuel system components.
CAUTION: After relieving the system pressure, a
small amount of fuel may be released when servicing
fuel lines or connections. Reduce the chance of
personal injury by covering the fuel line fittings with
a shop towel before you disconnect the fittings. The
towels will absorb any fuel that may leak out. When
the disconnect is completed, place the towel in an
approved container.
1. Remove the fuel cap.2. Remove the fuel pump relay from the underhood
relay box. Refer to
Fuel Pump Relay section.
014RY00004
3. Start the engine and allow it to stall.
4. Crank the engine for 30 seconds.
5. Disconnect the negative battery cable.
Fuel Pump Assembly
Removal Procedure
Refer to Fuel Tank In Fuel Pump Relay section.
014RW133