relay ISUZU TF SERIES 2004 Workshop Manual

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-377
FUEL PRESSURE REGULATOR

Removal Procedure
CAUTION: To reduce the risk of fire and personal
injury, it is necessary to relieve the fuel system
pressure before servicing the fuel system
components.
CAUTION: After relieving the system pressure, a
small amount of fuel may be released when
servicing fuel lines or connections. Reduce the
chance of personal injury by covering the fuel line
fittings with a shop towel before disconnecting the
fittings. The towels will absorb any fuel that may
leak out. When the disconnect is completed, place
the towel in an approved container.
NOTE: Compressed air must never be used to test
or clean a fuel pressure regulator, as damage to the
fuel pressure regulator may result.
NOTE: To prevent damage to the fuel pressure
regulator, do not immerse the pressure regulator in
solvent.
1. Depressurize the fuel system. Refer to Fue
l
Pressure Relief Procedure.
2. Disconnect the negative battery cable.
3. Remove the fuel pump relay. Refer to Fuel Pump
Relay.
4. Remove the pressure regulator hose from the fuel
pressure regulator.
5. Remove the two bolts from the protector tha
t
secures the common chamber.



060RW066

6. Remove the fuel pressure regulator attaching
screw.




060RW116
7. Remove the fuel pressure regulator from the fuel
rail.

Disassembly Procedure
1. Remove the O-ring from the fuel pressure regulator.
2. Remove the fuel return line from the fuel pressure
regulator.
3. Remove the O-ring from the fuel return line.
 The O-ring may be left inside the fuel pressure
regulator instead of on the fuel return line.




060RW116

6E-378 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Assembly Procedure
1. Install a new O-ring on the fuel return line.
2. Install the fuel return line on the fuel pressure
regulator.
Do not over-tighten the swivel nut on the fuel pressure
regulator. The fuel pressure regulator can be damaged
and fuel may leak if the swivel nut is over-tightened.
3. Tighten the swivel nut.
4. Install a new O-ring on the fuel pressure regulator.

Installation Procedure
1. Install the fuel pressure regulator attaching screw.
Tighten
 Tighten the fuel pressure regulator attaching scre
w
to 3 Nm (0.3 kgm/26 lb in.).




060RW116
2. Install the fuel pressure regulator on the fuel rail.

3. Install the two bolts to the protector that secures
the common chamber.



060RW066
4. Install the pressure regulator hose to the fuel
pressure regulator.
5. Install the fuel pump relay. Refer to Fuel Pump
Relay.
6. Connect the negative battery cable.
7. Crank the engine until it starts. Cranking the engine
may take longer than usual due to trapped air in the
fuel lines.

ENGINE LUBRICATION (6VE1 3.5L) 6G-7
Oil Pan and Crankcase
Removal
1. Disconnect battery ground cable.
2. Drain engine oil.
3. Lift vehicle by supporting the frame.
4. Remove front wheels.
5. Remove oil level dipstick from level gauge tube.
6. Remove stone guard.
7. Remove radiator under fan shroud.
NOTE: For 4WD model, remove front axle housing
assembly from chassis (steps 8 to 10).
8. Remove suspension cross member fixing bolts, 2
pcs each per side and remove suspension cross
member.
9. Remove pitman arm and relay lever assembly,
using the 5–8840–2005–0 remover, remove pitman
arm from the steering unit and remove four fixing
bolts for relay lever assembly.
10. Remove axle housing assembly four fixing bolts
from housing isolator side and mounting bolts from
wheel side. At this time support the axle with a
garage jack and remove axle housing assembly.
11. Remove oil pan fixing bolts.
12. Remove oil pan, using 5–8840–2153–0 seale
r
cutter, remove oil pan.



013RS003
13. Remove crankcase fixing bolts.
14. Remove crankcase, using 5–8840–2153–0 seale
r
cutter, remove crankcase.

NOTE: Do not deform or damage the flange of oil pan
and crankcase.
Replace the oil pan and/or crankcase if deformed o
r
damaged.



013RS003
Installation
1. Install crankcase.
1. Remove residual sealant, lubricant and moisture
from mounting surface, then dry thoroughly.
2. Properly apply a 4.5 mm (0.7 in) wide bead o
f
sealant (TB-1207C or equivalent) to mounting
surface of crankcase.
Sealant beat must be continuous.
 The crankcase must be installed within 5
minutes after sealant application before the
sealant hardens.





013RW010

6G-8 ENGINE LUBRICATION (6VE1 3.5L)
3. Install crankcase, tighten crankcase fixing bolts
to the specified torque.
Torque : 10 N




m (1.0 kg




m/89 lb in)





013RW004
2. Install oil pan
1. Remove residual sealant, lubricant and moisture
from mounting surface, then dry thoroughly.
2. Properly apply a 4.5 mm (0.17 in) wide bead o
f
sealant (TB-1207C or equivalent) to mounting
surface of oil pan.
Sealant beat must be continuous.
 The crankcase must be installed within 5
minutes after sealant application before the
sealant hardens.




013RW003

3. Install oil pan, tighten oil pan fixing bolts to the
specified torque.
Torque : 25 N




m (2.5 kg




m/18 lb ft)
3. Install axle housing assembly and tighten fixing
bolts to the specified torque (4WD model).
Axle case bolts
Torque : 116 N




m (11.8 kg




m/85 lb ft)
Mounting bolts
Torque : 168 N




m (17.2 kg




m/124 lb ft)




RTW34CSH000101
4. Install relay lever assembly and tighten fixing bolts.
Torque: 44 N




m (4.5 kg




m/32 lb ft)
5. Engage teeth of pitman arm and steering unit, and
tighten nut to the specified torque.
Torque : 216 N




m (22.0 kg




m/159 lb ft)
6. Install suspension cross member and tighten fixing
bolts to the specified torque.
Torque : 78 N




m (8.0 kg




m/58 lb ft)
7. Install radiator under fan shroud.
8. Install stone guard.
9. Install engine oil level dipstick.
10. Fill engine oil until full level on engine oil gauge
dipstick.

ENGINE DIAGNOSIS (C24SE) 6-3
3.Trouble in Fuel System
Condition Possible cause Correction
Starting motor turns over and
spark occurs but engine does not
start. Fuel tank empty Fill
Water in fuel system Clean
Fuel filter clogged Replace filter
Fuel pipe clogged Clean or replace
Fuel pump defective Replace
Fuel pump circuit open Correct or replace
Evaporative Emission Control
system circuit clogged Correct or replace
Multiport Fuel Injection System
faulty Refer to "Electronic Fuel Injection"
section
4.Engine Lacks Compression
Condition Possible cause Correction
Engine lacks compression Spark plug loosely fitted or spark
plug gasket defective Tighten to specified torque or
replace gasket
Spark plug wire incorrect Connect properly or replace
Valve timing incorrect Adjust
Cylinder head gasket defective Replace gasket
Valve incorrectly seated Lap valve
Valve stem seized Replace valve and valve guide
Valve spring weakened Replace
Cylinder or piston rings worn Overhaul engine
Piston ring seized Overhaul engine.

Engine Compression Test Procedure
1. Start and run the engine until the engine
reaches normal operating temperature.
2. Turn the engine off.
3. Remove all the spark plugs.
4. Remove ignition coil fuse (15A) and disable the
ignition system.
5. Remove the fuel pump relay from the relay and
fuse box. 6. Engage the starter and check that the cranking
speed is approximately 300 rpm.
7. Install cylinder compression gauge into spark
plug hole.
8. With the throttle valve opened fully, keep the
starter engaged until the compression gauge
needle reaches the maximum level. Note the
reading.
9. Repeat the test with each cylinder.
The pressure difference between the individual
cylinders should not exceed 100kPa (14.5 psi).

6-4 ENGINE DIAGNOSIS (C24SE)
Rough Engine Idling or Engine Stalling
Condition Possible cause Correction
Trouble in fuel injection system Idle air control valve defective Replace
Throttle shutting off incomplete Correct or replace
Throttle position sensor circuit
open or shorted Correct or replace
Fuel injector circuits open or
shorted Correct or replace
Fuel injectors damaged Replace
Fuel pump relay defective Replace
Manifold Absolute Pressure
Sensor cable disconnected or
broken Correct or replace
Manifold Absolute Pressure
Sensor defective Replace
Engine Coolant Temperature
Sensor cable disconnected or
broken Correct or replace
Engine Coolant Temperature
Sensor defective Replace
Intake Air Temperature sensor
cable disconnected or broken Correct or replace
Intake Air Temperature sensor
defective Replace
Knock Sensor (KS) circuits open
or shorted Correct or replace
KS defective Replace
KS Module circuits open or
ground Correct or replace
KS Module defective Replace
Vehicle Speed Sensor circuit open
or shorted Correct or replace
Vehicle Speed Sensor defective Replace
Trouble in emission control
system Engine Control Module defective Replace
Canister purge solenoid circuit
open Correct
Canister purge solenoid defective Replace
Evaporative Emission Canister
Purge control valve defective Replace
Trouble in ignition system Refer to Hard Start
Troubleshooting Guide
Others Engine lacks compression Refer to Hard Start
Troubleshooting Guide
Valve incorrectly seated Lap valve
Air Cleaner Filter clogged Replace filter element
Valve timing incorrect Readjust
Idle air control valve broken Replace

ENGINE DIAGNOSIS (C24SE) 6-11
Abnormal Combustion
Condition Possible cause Correction
Trouble in fuel injection system Fuel pressure control valve
defective Replace
Fuel filter clogged Replace
Fuel pump clogged Clean or replace
Fuel tank or fuel pipe clogged Clean or replace
Fuel injector clogged Clean or replace
Fuel pump relay defective Replace
Power supply cable for fuel pump
loosely connected or defective Reconnect, correct or replace
Manifold Absolute Pressure
Sensor circuit open or shorted Correct or replace
Manifold Absolute Pressure
Sensor defective Replace
Engine Coolant Temperature
(ECT) Sensor circuit open or
shorted Correct or replace
ECT Sensor defective Replace
Throttle Position Sensor
adjustment incorrect Reconnect
Throttle Position Sensor defective Replace
Throttle Position Sensor
connector loosely connected Reconnect
Vehicle Speed Sensor cable
loosely connected or defective Correct or replace
Vehicle Speed Sensor loosely
fixed Fix tightly
Vehicle Speed Sensor in wrong
contact or defective Replace
Engine Control Module cable
loosely connected or defective Correct or replace
Trouble in emission control
system Heated Oxygen Sensor circuit
open (If applicable) Correct or replace
Heated Oxygen Sensor defective
(If applicable) Replace
Signal vacuum hose loosely fitted
or defective Correct or replace
ECT Sensor circuit open or
shorted Correct or replace
ECT Sensor defective Replace
Evaporative Emission Control
system (If applicable) Refer to Section 6E
Trouble in ignition system - Refer to "Engine Lacks Power"
Trouble in cylinder head parts Carbon deposits in combustion
chamber Remove carbon
Carbon deposit on valve, valve
seat and valve guide Remove carbon

ENGINE FUEL (C24SE) 6C-1
ENGINE
ENGINE FUEL (C24SE)
CONTENTS

General Description............................................. 6C-2
Service Precaution............................................... 6C-3
Fuel Metering........................................................ 6C-4
Fuel Filter............................................................... 6C-5
Removal.............................................................. 6C-5
Inspection........................................................... 6C-6
Installation.......................................................... 6C-6
Inspection........................................................... 6C-6
In-Tank Fuel Filter............................................. 6C-6
Fuel Pump Flow Test....................................... 6C-7
Fuel Pump.............................................................. 6C-8
Fuel Pump and Associated Parts................. 6C-8
Removal.............................................................. 6C-8
Installation.......................................................... 6C-9
Fuel Tube / Quick - Connector Fittings.......... 6C-10
Precautions........................................................ 6C-10
Cautions During Work..................................... 6C-10

Removal............................................................... 6C-10
Reuse of Quick-Connector............................. 6C-11
Assembling Advice........................................... 6C-11
Fuel Pump Relay................................................... 6C-12
General Description.......................................... 6C-12
Fuel Tank................................................................ 6C-13
Fuel Tank and Associated Parts.................... 6C-13
Removal............................................................... 6C-14
Installation.......................................................... 6C-14
Filler Neck............................................................... 6C-15
Removal............................................................... 6C-15
Installation.......................................................... 6C-15
Fuel Gauge Unit.................................................... 6C-15
Removal and Installation................................. 6C-15
Fuel Filler Cap........................................................ 6C-16
General Description.......................................... 6C-16
Inspection............................................................ 6C-16
Main Data and Specifications............................ 6C-17
Special Tool........................................................ 6C-18

ENGINE FUEL (C24SE) 6C-7
Fuel Pump Flow Test
If reduction of fuel supply is suspected, perform the
following checks.
1. Make sure that there is fuel in the tank.
2. With the engine running, check the fuel feed pipe
and hose from fuel tank to injector for evidence o
f
leakage. Retighten, if pipe or hose connection is
loose. Also, check pipes and hoses for squashing
or clogging.
3. Insert the hose from fuel feed pipe into a clean
container, and check for fuel pump flow rate.
4. Connect the pump relay terminals (2) with a
jumper wire (1) as shown and start the fuel pump
to measure delivery.




RTW36CSH000201
CAUTION: Never generate sparks when connecting
a jumper wire.

Delivery Delivery
15 seconds 0.38 liters minimum
If the measure value is out of standard, conduct the
pressure test.
Pressure test
For the pressure test to the fuel system, see Section 6E
“Fuel Control System".

6C-12 ENGINE FUEL (C24SE)
Fuel Pump Relay
General Description
In order to control the fuel pump and sender assembly
(FPAS) operation, the FPAS relay is provided. When
the starter switch is turned to “ON" position, the FPAS
relay operates the FPAS for 2 seconds.
When it is turned to “START" position, the Engine
Control Module receives the reference pulse from the
Ignition Control Module and it operates the relay, again
causing the FPAS to feed fuel.