manual transmission ISUZU TF SERIES 2004 Workshop Manual

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-11

Comparison of mode
1. The normal drive mode is set at the normal shift
points.
2. The shift points of the power drive mode are shifted
to the higher speed side, compared to the normal
drive mode.
3. The 3rd start mode is a special mode used
exclusively for starting in third gear.
3rd start Mode
1. The 3rd start switch will operate when switched on
after all of the following conditions are present:
a. The gear select position is “D" range only.
b. Vehicle speed is 11 km/h (7 mph) or less.
c. Transmission oil temperature is 120

C (248

F)
or less.
d. Accelerator opening is at 8% or less.
2. Cancel Release
1. Cancellation by driver
a. Turning off the 3rd start mode switch
b. Shifting select position to “3", “2", or “L" (3rd
start mode is not canceled by selecting “N",
“ R", or “P")
c. Ignition key is turned off.
2. Automatic cancellation
a. When vehicle runs at 34 km/h (21mph) o
r
more for 1 second or more
b. When transmission oil temperature reaches 120

C (284

F) or above
NOTE: The mode returns to normal drive mode o
r
power drive mode after the 3rd start mode is canceled.
Backup Mode
If a major system failure occurs which could affect
safety or damage the transmission under normal
vehicle operation, the diagnostic system detects the
fault and overrides the Transmission Control Module
(TCM).
The “CHECK TRANS" light flashes to alert the driver,
and the transmission must be manually shifted as
follows:


Select lever position Gear Ratio Selected
D 4 (Fourth)
Manual 3 4 (Fourth)
Manual 2 3 (Third)
Manual L 3 (Third)
R Reverse
Shifts are firmer to prevent clutch slip and consequent
wear. The fault should be corrected as soon as
possible.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-39

DTC P0705 (FLASHING CODE 17) Transmission Range Sensor Circuit
Malfunction


RTW37ALF000501

Circuit Description
The neutral start switch gives the signals related to the
selector lever position (PRND32L) to the Transmission
Control Module (TCM). The neutral start switch turns on
when the select lever is shifted to the P, R, N, D, 3, 2 o
r
L range. The neutral start switch, which is connected to
the starter switch circuit, is available only when the
select lever is in the P or N range (Engine run).
The neutral start switch is connected to the
transmission manual shaft and installed in the
transmission case.

Condition for setting the DTC

The TCM detects following "Condition 1" for 30 sec
continuously.
 The TCM detects following "Condition 2" for 10 sec
continuously.
Condition 1("Open"):
When the TCM detects no signal of range senso
r
more than 2.0 sec at following conditions.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-55

DTC P0743 (FLASHING CODE 33) Torque Converter Clutch Electrical


RUW37ALF000601
Circuit Description
The lock-up solenoid SL of the torque converter clutch
(TCC) controls the lock-up clutch by a signal according
to the lock-up range judgment of the TCM when the
vehicle runs.
This function can improve the fuel consumption to
almost the same extent as the manual transmission.
The lock-up solenoid SL is put into B+ by the TCM, so
that the solenoid is actuated with the result of lock-up.
Condition for setting the DTC
The TCM detects following conditions both "Condition
1" and "Condition 2" occur 2 times or more than it.
Condition 1 ("GND short"):

Voltage at connector pin is 0V for 0.3 sec
continuously when solenoid is “ON".
Condition 2 ("Open or IG short"):

Voltage at connector pin is ignition voltage for 0.5
sec continuously when solenoid is “OFF".
Action Taken When The DTC Sets

No lock-up control.
 The TCM fixes to 1st gear when the vehicle speed is
less than 6 mph.

Check Trans ON.

DTC stored.

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

7A3-12 ON-VEHICLE SERVICE (AW30 –40LE)

Manual Shifting Test
NOTE: With this test, it can be determined whether the
trouble lies within the electrical circuit or is a mechanical
problem in the transmission.
1. Disconnect TCM connector
Inspect manual driving operation
2. Inspect manual driving operation
Check that the shift and gear positions correspond
with the table.
If the “L", “2", “3" and “D" range gear positions are
difficult to distinguish, do perform the following road
test.
While driving, shift through the “L", “2", “3" and “D"
ranges. Check that the gear change corresponds to
the gear position.
If any abnormality is found in the above test, do
perform the stall, time lag or gear change tests.



RUW37ASH004101
3. Connect TCM connector
With the engine off, connect the TCM connector.


Stall Test



RUW37ALH000101
The object of this test is to check the overall
performance of the transmission and engine b
y
measuring the maximum engine speeds at the “D" and
“ R" ranges.
NOTE:
1. Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).
2. Do not continuously run this test longer than 5 seconds.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-31

Shift Cable





RTW47ALF000101
Legend

(5) Bracket
(1) Select lever
(6) Clip
(2) Shift cable retaining pawl
(7) Shift cable
(3) Manual shaft select lever
(8) Select lever base
(4) Adjuster


Remove or Disconnect
1.
Block the wheels.
2.
Disconnect the negative battery cable.
3.
Move the select lever to the “N ” position.
4.
Remove the rear console and front console.
5.
Disconnect the shift cable from the select lever.
6.
Press on the shift cable retaining pawl to remove the
cable from the select lever base.
7.
Disconnect the shift cable from the transmission
side.
8.
Remove the shift cable from the bracket.
9.
Pull the shift cable free from the bottom of the
vehicle.

7A3-32 ON-VEHICLE SERVICE (AW30 –40LE)

Install or Connect
1.
Install the shift cable toward the inside of the cabin
from the bottom of the vehicle.
2.
Push the shift cable into the select lever base.
3.
Connect the shift cable to the select lever.
4.
Fix the shift cable to the bracket.
Install the clip on the marking of shift cable.
5.
Check that the select lever is in the “N ” position.
6.
Check that the transmission is in the “N ” position.




249R300002
7.
Slide the cover in the direction shown by the arrow
(1).
8.
Use an ordinary screwdriver to move the lock piece
from the position indicated by the arrow (2). Continue
to move the lock piece until the adjuster position
begins to change.

P1010012

9.
Connect the shift cable to the manual shaft select
lever at the transmission side.
10.
Insert the lock piece to the adjuster (cable length
adjustment).
11.
Slide the cover on the adjuster and secure lock
piece.

P1010016-2
11.
Press the select lever knob button 5 times.
Then check that the select lever moves smoothly to each of its positions.
13.
Check that the shift position indicated by the select
lever and the actual shift position are the same.
14.
Install the front console and rear console.
15.
Connect the negative battery cable.
16.
Remove the wheel blocks.

UNIT REPAIR (AW30–40LE) 7A4–5
Components (1)
Reassembly
1. Install a new gasket and the ex tension housing
(4
2) to the transmission case.
Torque: 36 N·m (27 Ib ft)
2. Install the speedometer driven gear, plate, and
speedometer sensor (4
2).
To r q u e :
Plate bolt – 15 N·m (11 Ib ft)
Speedometer sensor – 25 N·m (18 Ib ft)
3. Install the adapter housing (4
4).
Remove any gasket material on the contacting
surfaces of the adapter housing and transmission
case.
24 1RY 0 002 0
Apply liquid gasket (TB1281–B or its equivalent)
(1) and install the apply gaskets (2) to the adapter
housing as shown in the figure.
Install the adapter housing to the transmission
case.
Torque: 34 N·m (25 Ib ft)
4. Install the neutral start switch.
Using the transmission select lever, fully turn the
manual valve lever shaft back and return two
notches.
It is now in neutral.
Insert the neutral start switch onto the manual
valve lever shaft and temporarily tighten the
adjusting bolt.
Install the lock washer and nut.
Torque: 7 N·m (61 Ib in)Align the neutral standard line and the switch
groove and tighten the adjusting bolt.
Torque: 13 N·m (113 Ib in)
Bend the tabs of the lock washer.
NOTE: Bend at least two of the lock washer tabs.
RUW1 7A SH01 3601
5. Install the oil temperature sensor to the transmission
case.
Torque: 15 N·m (11 Ib ft)
RUW3 7A SH00 4001

7A4–92 UNIT REPAIR (AW30–40LE)
Transmission Valve Body assembly
Disassembled View
2 40R20 0039
E nd O FCallo ut
Legend
(1) Detent spring
(2) Manual shift valve
(3) Upper valve body
(4) No.1 gasket (Upper valve body side)(5) Valve body plate
(6) Clamp
(7) Pressure control solenoid
(8) No.2 gasket (Lower valve body side)
(9) Lower valve body

UNIT REPAIR (AW30–40LE) 7A4–121
Transmission Case
Disassembled View
24 9RY 0 0001
E nd O FCallo ut
Disassembly
1. Using a chisel, cut off the spacer and remove it from
the shaft.
24 9RY 0 0002
Legend
(1) Spacer
(2) Pin
(3) Manual valve lever shaft(4) Manual valve lever
(5) Oil seal
(6) Oil seal