length ISUZU TF SERIES 2004 User Guide

5C-50 BRAKES












20. Lever ; adjuster
21. Ring ; Adjuster lever


Apply grease to the lever ; adjuster sliding surface.
Install the lever ; adjuster and the ring to the shoe ;
trailing.


Be sure to use new ring.

P1010008B


23. Pin ; shoe hold
24. Spring ; shoe hold

Install the brake drum.


Install the rear wheel.


If the wheel cylinder has been removed, the brake
system must be bled.


Pump the brake pedal 10 times. Check that there is little
or no stroke length variation as the pedal is pumped.


Adjust the lining clearance.




Brake Line
Torque N
m(kgf
m/Ib
ft)
13 - 19 (1.3 - 1.9 / 9 - 14)

BRAKES 5C-61


















4) Measure dimension (A)

RTW35CSH000801







5) Calculate the gap (B-A) when assembling the master
cylinder and vacuum booster.

GAP mm (in
)
0 
0.4 (0 
0.0157)



6) If dimension (A) is out of the standard range, adjust the
push rod.

Loosen the push rod lock nut (1) on the vacuum
booster.

Set the clevis (2).

Use the adjuster (3) to adjust the length of the
protruding portion of the push rod.

Vacuum (negative) pressure should be GASOLINE
ENGINE: 66.7 kPa (500mm Hg) or DIESEL
ENGINE: 93.3 kPa (700mm Hg) after adjustment.

Tighten the push rod lock nut to the specified torque.







Torque N

m(kgf

m/lb

ft)
18 – 25 (1.8 – 2.5 / 13 – 18)

7) Install the vacuum booster assembly to the dash panel
and pedal mounting bracket.
Torque N

m(kgf

m/lb

ft)
18 – 24 (1.8 – 2.4 / 13 – 17)

CAB 10-5



Important Operations - Installation
1. Engine Hood Rear Seal
Install the engine hood rear seal as shown in the illustration.
1 : Seal
2 : Clip
3 : Rear (windshield glass side)
4 : Front

RTW3A0SH000201

3. Windshield Glass
1) Clean the windshield glass bonding surface.
2) Use a soft rag and unleaded gasoline to wipe off an
y
adhesive remaining on the body.
3) Mount the body window glass as shown in the illustration.
Attach spacers at five locations.


Always use new spacer.
4) Install the windshield upper molding.


Peel off the tear-away paper from the windshield uppe
r
molding, and start applying it with one end of the glass
and cut away the surplus at the other end of the glass
for length adjustment.


Always use new upper molding.
5) Temporary install the windshield support.



6) Apply primer
1 Sunstar #435-98 or equivalent to the body
side bonding surface. The primer should extend at least 25
mm (1 in).
Apply primer Sunstar #435-40 or equivalent to the
windshield glass side bonding surface.
The primer should extend 16.5 mm (0.6 in) and 25 mm (1.0
in) from end of the glass.

8A-4 ELECTRICAL-BODY AND CHASSIS
GENERAL INFORMATION
The body and chassis electrical system operates on a twelve volt power supply with negative ground polarity.
The main harness consists of the engine harness, the instrument harness, the body harness, and the chassis
harness.
The harnesses use a split corrugated tube to protect the wires from the elements.
Wire size is determined by current flow, circuit length, and voltage drop.
All wires have color-coded insulation.
Wire color-codes are shown in the circuit diagrams.
This makes it easier to trace circuits and to make the proper connections.
Each circuit consists of the following:
1. Power source - The battery and the alternator
2. Wires - To carry electrical current through the circuit
3. Fuses - To protect the circuit against current overload
4. Relays - To protect voltage drop between the battery and the circuit parts and to protect the switch points against
burning
5. Switches - To open and close the circuit
6. Load - Any device, such as a light or motor, which converts the electrical current into useful work
7. Ground - To allow the current to flow back to the power source

ELECTRICAL-BODY AND CHASSIS 8A-9

SPLICING WIRE
Open the Harness
If the harness is taped, remove the tape.
To avoid wire insulation damage, use a sewing "seam ripper"
(available from sewing supply stores) to cut open the harness.
If the harness has a black plastic conduit, simply pull out the
desired wire.
Cut the wire
Begin by cutting as little wire off the harness as possible.
You may need the extra length of wire later if you decide to cut
more wire off to change the location of a splice.
You may have to adjust splice locations to make certain that
each splice is at least 1-1/2" (40 mm) away from other splices,
harness branches, or connectors.
Strip the insulation
When replacing a wire, use a wire of the same size as the
original wire.
Check the stripped wire for nicks or cut strands.
If the wire is damaged, repeat the procedure on a new section
of wire.
The two stripped wire ends should be equal in length.



Crimp the Wires
Select the proper clip to secure the splice.
To determine the proper clip size for the wire being spliced,
follow the directions included with your clips.
Select the correct anvil on the crimper.
(On most crimpers your choice is limited to either a small or
large anvil.)
Overlap the two stripped wire ends and hold them between
your thumb and forefinger.
Then, enter the splice clip under the stripped wires and hold it
in place.




Open the crimping tool to its full width and rest one handle
on a firm flat surface.

Center the back of the splice clip on the proper anvil and
close the crimping tool to the point where the back of the
splice clip touches the wings of the clip.

Make sure that the clip and wires are still in the correc
t
position. Then, apply pressure until the crimping tool closes.



Before crimping the ends of the clip, be sure that:

The wires extend beyond the clip in each direction.

No strands of wire are cut loose.

No insulation is caught under the clip.
Crimp the splice again, once on each end.
Do not let the crimping tool extend beyond the edge of the clip
or you may damage or nick the wires.

6A – 90 ENGINE MECHANICAL






CONNECTING ROD
Connecting Rod Alignment
Use a connecting rod aligner to measure the distortion and the
parallelism between the connecting rod big end hole and the
connecting rod small end hole.
If either the measured distortion or parallelism exceed the
specified limit, the connecting rod must be replaced.


Connecting Rod Alignment Per Length of 100 mm (3.94 in)
mm (in)
Standard Limit
Distortion 0.08 (0.003) or Less 0.20 (0.008)
Parallelism 0.05 (0.002) or Less 0.15 (0.006)


Connecting Rod Side Face Clearance
1. Install the connecting rod to the crankpin.
2. Use a feeler gauge to measure the clearance between the
connecting rod big end side face and the crankpin side
face.
If the measured value exceeds the specified limit, the
connecting rod must be replaced.


Connecting Rod Big End and Crankpin Side Face Clearance
mm (in)
Standard Limit
0.23 (0.009) 0.35 (0.014)


Piston Pin and Connecting Rod Small End
Bushing Clearance
Use a caliper calibrator and a dial indicator to measure the
piston pin and connecting rod small end bushing clearance.
If the clearance between the piston pin and the connecting rod
small end bushing exceeds the specified limit, replace the
piston pin and/or the connecting rod.


Piston Pin and Connecting Rod Small End
Bushing Clearance
mm (in)
Standard Limit
4JA1T (L) 0.008-0.020
(0.003-0.0008) 0.050 (0.002)
4JA1TC,
4JH1TC 0.005-0.018
(0.0002-0.0007) 0.050 (0.002)

015LX034
011RY00029
015LX028

FUEL SYSTEM 6C – 17
FILLER NECK
Removal
1.
Remove the fuel tank.
NOTE: Refer to "Fuel Tank" in this section.
2.
Put a marking the following point as the filler neck assembl
y
is restored.


Each joint area of the hose (to restore axial direction and
insertion length of the hose)


Each fasten area of the clamp (to restore axial direction
and position of the clamp)


Each bolt in the clamp (to restore fasten length of bolt in
the clamp)


The band clip (to restore position and fasten length o
f
the band clip)
NOTE: Cover end of each hose and pipe to prevent any dust
entering.









Installation
1.
Align each marking and restore the following point.


Each joint area of the hose (Restore axial direction and
insertion length of the hose)


Each fasten area of the clamp (Restore axial direction
and position of the clamp)


Each bolt in the clamp (Restore fasten length of bolt in
the clamp)
Torque N·m (kg·m / lb ft)
2.5 (0.25 / 21.7)
filler neck side except flat deck model.


The band clip (Restore position and fasten length of the
band clip)
2.
Install the fuel tank.
NOTE: Refer to "Fuel Tank" in this section.

6C – 32 FUEL SYSTEM

4. Install the pin to the dial gauge.
Note:
The lengths of the pins do not include the
threaded portions.

Pin (L=100 mm): 157892-5200 (Bosch AS)
Dial gauge: 157954-3800 (Bosch AS)
185317-0150 (ISUZU)



5. Secure the dial gauge to the nozzle holder using the
nut so that the pin contacts the tip of the first spring
seat.

CAUTION:
 Secure the dial gauge so that a stroke of 2 mm can
be measured.

 Do not over-tighten the nut as the dial gauge shaft
may jam. (Confirm from the dial gauge that the
shaft moves smoothly.)




6. Set the nozzle holder to the nozzle tester and put
needle to zero on the dial gauge.
7. Operate the nozzle tester to bleed any air from inside
the retaining nut and to confirm that no fuel leaks.



040MV029.tif
040MV009.ti
f
040MV030.ti
f

ENGINE ELECTRICAL 6D – 13
STATOR COIL ASSEMBLY
1. Check for continuity across the stator coils.
If there is no continuity, the stator coils must be
replaced.
Resistance Between The Terminal “N” and the Coil Ends
(Reference) ohms
Standard 0.1

066RY00022 2. Check for continuity between each stator coils and the
stator core.
If there is continuity, the stator coils must be replaced.
066RY00023


RTW46DSH004801
BRUSH
Measure the length of the brush. If abrasion has reduced
the brush length to less than 6.5 mm, the brush must be
replaced with a new one.
A wear line is inscribed in the brush. If the line is not
visible, the brush must be replaced.
Brush Length (Reference) mm (in)

Standard Limit
25 (1.0) 6.5 (0.25)



RTW46DSH001201
Rectifier


Tester wire
E BAT
U, V, and WN ⊕  U, V, and WN⊕ 
⊕ ----- Conductivity ⊕ ----- No
conductivity

No
conductivity -----
 Conductivity -----
Negative side diode check Positive side diode check

6D – 28 ENGINE ELECTRICAL
BRUSH AND BRUSH HOLDER
1. Use a vernier caliper to measure the brush length (four
brushes).
Replace the brushes as a set if one or more of the
brush lengths is less than the specified limit.
Brush Length mm (in)
Standard Limit
15 (0.59) 12 (0.47)


RTW46DSH004001













RTW46DSH004101
2. Use a circuit tester to check the brush holder
insulation.
Touch one probe to the holder plate and the other
probe to the positive brush holder.
There should be no continuity.





3. Inspect the brushes for excessive wear.
If the negative brushes have excessive wear, the
entire brush holder assembly must be replaced.
If the positive brushes have excessive wear, the entire
yoke must be replaced.

OVERRUNNING CLUTCH
1. Inspect the overrunning clutch gear teeth for
excessive wear and damage.
Replace the overrunning clutch if necessary.
2. Rotate the pinion clockwise.
It should turn smoothly.
3. Try to rotate the pinion in the opposite direction.
The pinion should lock.
065RY00035


RTW46DSH004401
BEARING
Inspect the bearings for excessive wear and damage.
Replace the bearings if necessary.