ISUZU TF SERIES 2004 Workshop Manual

ANTITHEFT SYSTEM 11B – 25
Tech-2 Features
1. Tech-2 is a 12volt system. Do not apply 24
volts.
2. After connecting and/or installing the vehicle
communication interface (VCI) module, PCMCIA
card and data link connector (DLC) to the Tech-
2, connect the tool to the vehicle DLC.
3. Make sure the tech-2 is OFF when removing or
installing the PCMCIA card.
4. The Tech-2 has the capability of two or three
snapshot.
5. The PCMCIA card is sensitive to magnetism and
static electricity, so care should be taken in the
handling of the card.
6. Always return to the Main Menu by pressing
the EXIT key several times before shutting
down.
7. To clear diagnostic trouble codes (DTCs), open
Application Menu and press “Clear DTC”.
Getting Started
Before operating the Isuzu PCMCIA card with the
Tech-2, the following steps must be performed:
1. The Isuzu System PCMCIA card inserts into the
Tech-2.
2. Connect the SAE 16/19 adapter to the DLC
cable.
3. Connect the DLC cable to the Tech-2.
4. Mark sure the vehicle ignition is off.
5. Connect the Tech-2 SAE 16/19 adapter to the
vehicle DLC.
6. Turn the vehicle ignition (key) switch.
7. Power the Tech-2 ON and verify the Tech-2
power up display.
8 7 6 5 4 3 2 1
16 15 14 13 12 11 10 9
060R300015
Press (ENTER) To Continue
060RW009

11B – 26 ANTITHEFT SYSTEM
Operating Procedure
The power up screen is displayed when you power
up the tester with the Isuzu systems PCMCIA card.
Follow the operating procedure below.
Press (ENTER) To Continue
F0 : Diagnostics
F1 : View Capture Data
F2 : Tool Options
F3 : Down load/Up load Help
Vehicle Identification
Select one of the following
Model Year(S)(ENTER)
(F0 ENTER)
(Model year ENTER)
060R100102
(UP) AXIOM
Vehicle Type
Antitheft
F0 : Powertrain
F1 : Chassis
F2 : Body
Vehicle Identification
Select one of the following
Body(F2 ENTER)
(Vehicle Type ENTER)
Vehicle Identification
Select one of the following
System Selection Menu(UB) Trooper
(UE) Rodeo/Amigo
(TF) LUV,Frontier,LAO-RodeoVehicle Type(S)

ANTITHEFT SYSTEM 11B

11B – 28 ANTITHEFT SYSTEM
Arm/Disarm Signal Test
Arm/Disarm signal test is used to check
abnormalities in arm/disarm signal circuit.
1. Select “Body” and “Antitheft”.
2. Select “Actuator Test” and “Arm/Disarm Signal
Test”.
3. Observe the data list.
4. Insert the key into door key cylinder.
5. Remove the key into door key cylinder.
Horn Signal Test
Horn signal test is used to check abnormalities in
horn signal circuit.
1. Select “Body” and “Antitheft”.
2. Select “Actuator Test” and “Horn Signal Test”.
3. Observe the alarm sound.
4. Push “active bottom”.
5. Check the alarm sound function.Turn Signal Test
Turn signal test is used to check abnormalities in
turn signal circuit.
1. Select “Body” and “Antitheft”.
2. Select “Actuator Test” and “Turn Signal Test”.
3. Observe the flasher lamp.
4. Push “active bottom”.
5. Check the flasher lamp function.
Theft LED Test
Theft LED test is used to check abnormalities in
theft LED signal circuit.
1. Select “Body” and “Antitheft”.
2. Select “Actuator Test” and “Turn Signal Test”.
3. Observe the antitheft LED.
4. Push “active bottom”.
5. Check the antitheft function.
Arm/Disarm Signal Test
Arm/Disarm Signal DisarmedElectronic System; Anti Theft Warning
Quit
ArmDisarmed
RAW4B0SH000201
Horn Signal Test
Horn Signal Inactive 12VElectronic System; Anti Theft Warning
Quit
ActiveInactive
RAW4B0SH000301
Turn Signal Test
Turn Signal Inactive 12VElectronic System; Anti Theft Warning
Quit
ActiveInactive
RAW4B0SH000401
Theft LED Test
Theft LED OffElectronic System; Anti Theft Warning
Quit
OnOff
RAW4B0SH000501

ANTITHEFT SYSTEM 11B – 29
Programming
Programming antitheft function is used to input
security code for the antitheft system by tech 2.
If the remote key or ECU replaced, program as
necessary.
Erase Remote Keys
1. Select “Body” and “Antitheft”.
2. Select “Programming”.
3. Select “Erase Remote Keys”.
4. The following screen shows up.4. Confirm the following screen shows up.
Programming
F0; Erase Remote Keys
F1; Program Remote Key
F2; Program Anti Theft Warning
F3; Program Country Code
F4; Program Vehicle Option
RAW4B0SH000601
Not
OkayOkay Security Code
0000
Press ENTER Key to continue
060R200284
ConfirmSee Checking Procedure Before
Programming!
060R200289

11B – 30 ANTITHEFT SYSTEM
Program Remote Keys
1. Select “Body” and “Antitheft”.
2. Select “Programming”.
3. Select “Program Remote Keys”.
4. The following screen shows up.4. Confirm the following screen shows up.
5. Input the security code.
Programming
F0; Erase Remote Keys
F1; Program Remote Key
F2; Program Anti Theft Warning
F3; Program Country Code
F4; Program Vehicle Option
RAW4B0SH000601
Not
OkayOkay Security Code
0000
Press ENTER Key to continue
060R200284
ConfirmSee Checking Procedure Before
Programming!
060R200289

ANTITHEFT SYSTEM 11B – 31
Program Antitheft Warning
1. Select “Body” and “Antitheft”.
2. Select “Programming”.
3. Select “Program Antitheft Warning”.
4. The following screen shows up.4. Confirm the following screen shows up.
5. Input the security code.
Programming
F0; Erase Remote Keys
F1; Program Remote Key
F2; Program Anti Theft Warning
F3; Program Country Code
F4; Program Vehicle Option
RAW4B0SH000601
Not
OkayOkay Security Code
0000
Press ENTER Key to continue
060R200284
ConfirmSee Checking Procedure Before
Programming!
060R200289

11B

ANTITHEFT SYSTEM 11B – 33
Program Vehicle Options
1. Select “Body” and “Antitheft”.
2. Select “Programming”.
3. Select “Program Vehicle Options ”.
4. The following screen shows up.4. Confirm the following screen shows up.
5. Input the vehicle options.
Programming
F0; Erase Remote Keys
F1; Program Remote Key
F2; Program Anti Theft Warning
F3; Program Country Code
F4; Program Vehicle Option
RAW4B0SH000601
Not
OkayOkay Security Code
0000
Press ENTER Key to continue
060R200284
ConfirmSee Checking Procedure Before
Programming!
060R200289

11B – 34 ANTITHEFT SYSTEM
Tech-2 Data List
No. Streings Units
1 Battery Voltage V
2‘KEY-IN’ Status ON/OFF
3 CDLS-Motor Voltage (Central Door Locking System) V
4 Accident Sensor (Crash Sensor) Active/Inactive
5 Remote Key Active/Inactive
6 Remote-Key Detected Remote Key No.
7 Key Function Detected Lock/Unlock
8 Prev. Detected Remote-Key (Previously) Remote Key No.
9 Previously Key Function Lock/Unlock
10 Remote-Key 1 Status In Range/Not Programmed
11 Remote-Key 2 Status In Range/Not Programmed
12 Remote-Key 3 Status In Range/Not Programmed
13 Remote-Key 4 Status In Range/Not Programmed
14 Remote-Key 5 Status In Range/Not Programmed
15 Front Door Unlock Switch Active/Inactive
16 Front Door Lock Switch Active/Inactive
17 Front Door Lock Status Active/Inactive
18 Auto Door Unlock Switch Active/Inactive
19 Auto Door Lock Switch Active/Inactive
20 Auto Door Lock Status Active/Inactive
21 Trunk Signal Switch *Not used Open/Closed
22 Doorknob Switch Open/Closed
23 Doorknob Status Lock/Unlock
24 Trunk Doorknob Switch *Not used Open/Closed
25 Trunk Doorknob Status *Not used Lock/Unlock
26 Driver Door Switch Open/Closed
27 Driver Door Status Open/Closed
28 All Door Switch Open/Closed
29 All Door Status Open/Closed
30 Doorlock Tamper Switches Open/Closed
31 Engine Hood Switch Open/Closed
32 Engine Hood Status Open/Closed
33 Trunk Switch *Not used Open/Closed
34 Trunk Status *Not used Open/Closed
35 Pane Breakage Connected *Not used Yes/No
36 Pane Breakage Status *Not used Disabled/Abled
37 CDLS-Motor Current (Central Door Locking System) A
38 CDLS-Motor Unlock (Central Door Locking System) V
39 CDLS-Motor Lock (Central Door Locking System) V
40 Overflow Protection Active/Inactive
41 Turn Signal Active/Inactive
42 Horn Connected Yes/No
43 Horn Signal Active/Inactive
44 Theft LED ON/OFF
45 CDLS-Status (Central Door Locking System) Lock/Unlock
46 Selftest Request Active/Inactive
47 Last Use—
48 Theft Status Disabled/Abled
49 Alarm Status Active/Inactive
50 Security Wait Time Active/Inactive