4jh1 ISUZU TF SERIES 2004 Workshop Manual

EXHAUST SYSTEM 6F – 11
INSPECTION
4JA1T(L)



Vacuum switch valve (VSV)
Use a circuit tester to measure the V.S.V. resistance.
V.S.V Resistance  at 20°C
37 ~ 44

If the resistance is not within specification, replace it.



EGR Valve
Apply vacuum to the EGR valve, check to see the valve
operation.

Negative Pressure








4JA1TC/4JH1TC




RTW46ESH000301


EVRV
Use a circuit tester to measure the EVRV resistance.
EVRV Resistance  at 20°C
14

If the resistance is not within specification, replace it.

EGR Valve
Apply vacuum to the EGR valve, check to see the valve
operation.

Negative Pressure 4JH1TC

Less than 250 mmHg Not operation
More than 300 mmHg Operation

Negative Pressure 4JA1TC

Less than 100 mmHg Not operation
More than 170 mmHg Operation
Less then 180 mmHg Not operation
More than 240 mmHg Operation

6F – 12 EXHAUST SYSTEM
EGR COOLER (4JA1TC/4JH1TC EURO-III MODEL)
REMOVAL AND INSTALLATION




RTW46EMF000201

Removal Steps
1. Bolt
2. Gasket
3. Bolt
4. Gasket
5. Bolt
6. Bolt

7. EGR Pipe Assembly
8. Gasket
9. Bolt
10. EGR Cooler Assembly
11. Gasket
12. EGR Cooler Adapter


Removal
1. Bolt
2. Gasket
3. Bolt
4. Gasket
5. Bolt
6. Bolt
7. EGR Pipe Assembly
8. Gasket
9. Bolt
10. EGR Cooler Assembly
11.Gasket
12.EGR Cooler Adapter

EXHAUST SYSTEM 6F – 15
TURBOCHARGER
MAIN DATA AND SPECIFICATIONS

Engine 4JA1T(L) 4JA1TC 4JH1TC
Model IHI RHF4H IHI RHF4H IHI RHF5
Turbine type Mixed type
Compressor type Backword & rake type
Maximum permissible speed rpm 190,000 190,000 180,000
IHI : Ishikawajima Harima Heavy Industries., Ltd.

EXHAUST SYSTEM 6F – 17

INSPECTION AND REPAIR
Make the necessary adjustments, repairs, and part replacements if excessive wear or damage is discovered during
inspection.






















Turbocharger pressure check
1. Remove the hose between the master gate and the
compressor outlet pipe.
2. Connect the pressure gauge. To compressor outlet
pipe.
3. Start the engine and gradually increase the engine
speed (the vehicle must be stationary with no load
applied to the engine).
4. Check to see that turbocharger pressure rises to
approximately 300 mmHg.
Pressure Gauge : 5-8840-0075-0
150RY00030

Waste gate operation check
1. Remove the hose between the waste gate and the
compressor outlet pipe.
2. Connect the pressure gauge. To waste gate actuator.
3. Check to see that the rod begins to move when a
pressure of approximately 665 mmHg is applied to the
waste gate.
Note:
Do not apply a pressure greater than 1 kg/cm
2 to the
wastegate during this check.
150RY00031
Unit Inspection (Remove Turbo. from engine)
Check to see the pressure required to move the control
rod 2 mm is within the limits shown below.
Kpa/mmHg
4JH1TC 134.8/1011
4JA1TC 147.7/1108



150RY00032
Contact the “ISUZU MOTORS LIMITED” Dealer service
department or “IHI SERVICE FACILITY” for major repairs
and maintenance.
Important wheel shaft end play and bearing clearance
standards and limits are included below for your reference.

6H – 4 ACCELERATOR CONTROL

4JA1TC, 4JH1TC/RHD






RTW46HLF000201

ACCELERATOR CONTROL 6H – 5

4JA1TC, 4JH1TC/LHD




PTW46BMF000101

6E–70 ENGINE DRIVEABILITY AND EMISSIONS
Tech 2 Operating Flow Cart (Start Up)
Select “2.XL L4 HV240” in Vehicle Identification menu and the following table is shown in the Tech 2 screen.
System Selection Menu
F0: Powe rtra in
F1: Chassis
F3: Body
Select “(TF/UC)”.
Vehicle Identification
4JH1-TC Bosch
4JH1-T Denso
2.XL L4 HV240
3.5L V6 6VE1 Hita chi
AW30-40LE
AT JR405E
Select “F0: Powertrain”.
Main Menu
F0: Dia gnostic
F1: Se rvice Programming Syste m (SPS)
F2: View Capture Data
F3: Too l Optio n
F4: Do wnlo a d/ Uploa d He lp
Press “ENTER” key.
Ve hi cl e Ide nt ifi ca ti o n
(3) 2003
(2) 2002
(1) 2001
(Y) 2000
(X) 1999
(W) 1998
Select “F0: Diagnostic”.
Select “(3) 2003” or later.
Press (ENTER) to Co ntinue
Select “2.XL L4 HV240”.
Vehicle Identification
(UB) Troo pe r, Bigho rn
(UE) Rodeo,/Amigo, Wizard/Mu
(TF/UC) LUV, Fro ntier, LAO-Ro de o
(TBR)
(N*) ELF, NPR, NQR

0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE (For GENERAL EXPORT)
Items followed by an asterisk (*) require more frequent maintenance if the vehicle is driven under severe conditions.
Refer to "SEVERE CONDITIONS MAINTENANCE SCHEDULE."

I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate


SERVICE INTERVAL:

1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60or months whichever
comes fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
ENGINE Idling speed and acceleration
(GASOLINE) I I - I - I - I - I - I - I - I - I - I
(DIESEL) I I I I I I I I I I I I I I I I I I I I * Air cleaner element
(GASOLINE) - I - I - I - R - I - I - I - R - I - I
(DIESEL) I I I I I I I R I I I I I I I R I I I I * P Engine oil (6VE1) - R - R - R - R - R - R - R - R - R - R * P Engine oil (C24SE) Replace every 12,000km * D Engine oil (4JH1-TC) - R - R - R - R - R - R - R - R - R - R * D Engine oil (4JA1-TC) - - R - - R - - R - - R - - R - - R - - * D Engine oil (4JA1-T) RR R R RR RRRRRRRR R R R RRR * P Engine oil filter (6VE1) - R - R - R - R - R - R - R - R - R - R * P Engine oil filter (C24SE) Replace every 12,000km * D Engine oil filter (4JH1-TC, 4JA1-T) - R - R - R - R - R - R - R - R - R - R * D Engine oil filter (4JA1-TC) - - R - - R - - R - - R - - R - - R - - Oil leakage and contamination
(GASOLINE) - I - I - I - I - I - I - I - I - I - I
(DIESEL) I I I I I I I I I I I I I I I I I I I I Fuel leakage I I - I - I - I - I - I - I - I - I - I Fuel tank - - - | - - - | - - - | - - - | - - - | P O2 Sensor Replace every 160,000km P Valve clearances (6VE1) Check and adjust if noisy D Valve clearances A - - A - - - A - - - A - - - A - - - A P Spark plugs (C24SE) (for leaded
fuel use) - R - R - R - R - R - R - R - R - R - R
P Spark plugs (C24SE) (for unleaded
fuel use) - - - - - R - - - - - R - - - - - R - -
P Spark plugs (6VE1) Replace every 160,000km Spark plug wire | | - | - | - | - | - | - | - | - | - | Fuel filter (GASOLINE) - - - R - - - R - - - R - - - R - - - R Fuel filter (DIESEL) - - R - - R - - R - - R - - R - - R - - Engi ne / Accessory dri ve belt
(GASOLINE) - - - - - - - - - R - - - - - - - - - R
Fan belt tension and damage
(DIESEL) I I I I I I I I I I I I I I I I I I I I
* Exhaust system I I - I - I - I - I - I - I - I - I - I Engine coolant concentration (6VE1) - - - - - - - - - R - - - - - - - - - R (C24SE) - | - | - | - | - R - | - | - | - | - R Engine coolant level concentration
(DESEL) I I I I I I I I I R I I I I I I I I I R
Cooli ng sy stem for water l eakage - I - I - I - I - I - I - I - I - I - I All hoses and pipes in engine
compartment for clogs or damage - I - I - I - I - I - I - I - I - I - I
P Timing belt (C24SE) - - - - - - - - - - - - - - - I - - - - (Replace every 120,000km) P Timing belt (6VE1) Replace every 160,000km CLUTCH Cl utch fl ui d I I - I - I - I - I - I - I - I - I - I Clutch pedal travel and free play I I - I - I - I - I - I - I - I - I - I

MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SCHEDULE (For EUROPE)
Items followed by an asterisk (*) require more frequent maintenance if the vehicle is driven under severe conditions.
Refer to "SEVERE CONDITIONS MAINTENANCE SCHEDULE."
Diesel Engine model (ACEA B2 specification engine oil)

I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate


SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
DIESEL ENGINE * Engine oil (4JH1-TC) - R - R - R- R- R- R- R - R - R- R* Engine oil (4JA1-TC) - - R - - R - - R - - R - - R - - R - - * Engine oil filter(4JH1-TC) - R - R - R- R- R- R- R - R - R- R* Engine oil filter (4JA1-TC) - - R - - R - - R - - R - - R - - R - - Oil leakage and contamination I I I I I I I I I I I I I I I I I I I I Idling speed and acceleration I I I I I I I I I I I I I I I I I I I I Fan belt tension and damage I I I I I I I I I I I I I I I I I I I I Exhaust system I I - I - I - I - I - I - I - I - I - I All hoses and pipes in engine
compartment for clog of damage - I I I I I I I I I I I I I I I I I I I
Valve clearance (4JH1-TC) - - - A - - - A - - - A - - - A - - - A Valve clearance (4JA1-TC) - - A - - A - - A - - A - - A - - A - - * Air cleaner element (4JH1-TC) I I I I I I I R I I I I I I I R I I I I * Air clearance element (4JA1-TC) - - I I I I I I R I I I I I I I I R I I Fuel filter (4JH1-TC) - - R - - R - - R - - R - - R - - R - - Fuel filter (4JA1-TC) - - - - - - - - R - - - - - - - - R - - Engine coolant concentration (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Engine coolant concentration
(4JA1-TC) - - I - - I - - I - - I - - I - - I - - Cooling system for water leakage
(4JH1-TC) - I - I - I - I - I - I - I - I - I - I Cooing system for water leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - CLUTCH Clutch fluid (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Clutch fluid (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Clutch pedal travel and play (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Clutch pedal travel and play (4JA1-TC) - - I - - I - - I - - I - - I - - I - - TRANSMISSION OR TRANSMISSION
WITH TRANSFER CASE
* Manual transmission with fluid (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * Manual transmission with fluid
(4JA1-TC) - - R - - I - - R - - I - - R - - I - - * Transfer case oil (4JH1-TC) - - - I - - - I - - - I - - - I - - - I * Transfer case oil (4JA1-TC) - - R - - I - - R - - I - - R - - I - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Gear control mechanism for
looseness (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Gear control mechanism for
looseness (4JA1-TC) - - - - - - - - I - - - - - - - - I - I * AT Automatic transmission fluid
(4JH1-TC) - - - I - - - I - - - I - - - I - - - I * AT Automatic transmission fluid (4JA1-TC) - - - - - - - - I - - - - - - - - I - I * AT Transfer case oil (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * AT Transfer case oil (4JA1-TC) - - R - - I - - R - - I - - R - - I - -

0B-6 MAINTENANCE AND LUBRICATION




I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate
SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
PROPELLER SHAFT Loose connections (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Loose connections (4JA1-TC) - - I - - I - - I - - I - - I - - I - - * Universal joints and splines for wear (4JH1-TC) - I - I - I - I - I - I - I - I - I - I * Universal joints and splines for wear (4JA1-TC) - - I - - I - - I - - I - - I - - I - - 4WD Universal joints and sliding
sleeve (4JH1-TC) - L - L - L - L - L - L - L - L - L - L FRONT AND REAR AXLE * Differential gear oil (Front and rear) (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * Differential gear oil (Front and rear) (4JA1-TC) - - R - - I - - R - - I - - R - - I - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Shift on the fly system Gear oil (4JH1-TC) I - - I - - - I - - - I - - - I - - - I Gear oil (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Front axle shaft rubber boot for
damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Front axle shaft rubber boot for
damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Axle case for distortion or damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Axle case for distortion or damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Axle shafts for distortion or damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Axle shafts for distortion or damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - STEERING Power steering fluid (4JH1-TC) I I I I I I R I I I I I I R I I I I I I Power steering fluid (4JA1-TC) - - - - - - - - - - - I - - - - - - - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - R - - I - - R - - I - - R - - * Steering system for looseness or
damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I * Steering system for looseness or
damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Power steering hose (4JH1-TC) - I - I - I - I - I - I - R - I - I - I Power steering hose (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Steering wheel play (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Steering wheel play (4JA1-TC) - - I - - I - - I - - R - - I - - I - - Steering function (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Steering function (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Right and left turning radius (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Right and left turning radius (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Wheel alignment (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Wheel alignment (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Joint ball for oil leakage or damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Joint ball for oil leakage or damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Joint ball rubber boot for damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Joint ball rubber boot for damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - -