torque ISUZU TF SERIES 2004 Workshop Manual

ON-VEHICLE SERVICE (JR405E) 7A3-21
4. Remove the shift cable from the transmission.
P1010068
5. Remove the rear propeller shaft assembly.
6. Loosen (do not remove) the nuts securing the
exhaust manifold and the exhaust pipe.
7. Disconnect the harness connectors from the
transmission.
8. Remove the fuel pipe bracket.
P1010013

P1010014
9. Remove the ATF level dipstick and tube.
10. Remove the undercover.
11. Rotate the ring gear and remove the 6 torque
converter bolts.
P1010016
12. Remove the automatic transmission fluid cooling
pipe.
P1010060
13. Place a jack beneath the engine to support it.
14. Remove the 3rd crossmember.
15. Remove the transmission mount.
16. Lower the jack beneath the engine slightly to tilt the
engine and transmission. Do not allow the radiato
r
and air conditioner hoses to stretch.
17. Remove the bolts attaching the transmission to the
engine.
18. Lower the transmission from beneath the vehicle.
Take care not to damage the breathers.

Install or Connect
1. Install the transmission to the engine and tighten the
bolts.
Bolt torque : M10 40 N·m (30 lb·ft)
M12 76 N·m (56 lb·ft)
2. Install the cable bracket to the transmission.
3. Connect the engine harness connectors.

7A3-22 ON-VEHICLE SERVICE (JR405E)

4. Install the 3rd crossmember.
Bolt and Nut torque : 67 N·m (49 lb·ft)
Bolt torque : 50 N·m (37 lb·ft)
5. Install the automatic transmission fluid cooling pipe.
6. Install the torque converter bolts.
Bolt torque : 29 N·m (22 lb·ft)
7. Install the undercover.
Bolt torque : 9 N·m (78 lb·in)
8. Install the ATF level dipstick and tube.
9. Install the fuel hose bracket.
Bolt torque : 6 N·m (52 lb·in)

10. Tighten the nuts securing the exhaust manifold and
the exhaust pipe.
Bolt torque : 43 N·m (32 lb·ft)
11. Install the rear propeller shaft assembly.
Flange bolt torque : 63 N·m (46 lb·ft)
Center bearing bracket bolt torque :
69 N·m (51 lb·ft)
12. Install the shift cable.
13. Connect the negative battery cable.
14. Remove the safety stands.
15. Remove the wheels blocks.


Torque Specifications
RTW37ALF001501

UNIT REPAIR (JR405E) 7A4-3
Disassembly steps
1. Torque converter

Pull the torque converter free.
NOTE:
Place a pan beneath the torque converter to catch
automatic transmission fluid (ATF) spillage.

Draining the ATF from the torque converter.


01ASSY101

2. Turbine sensor and speed sensor

Remove the turbine sensor from the transmission case.



02ASSY103



Remove the speed sensor from the transmission case.



03ASSY106

3. Inhibitor switch
Remove the 2 bolts and the inhibitor switch from the
transmission case.


240L300002

4. Oil pan

Lift and support the transmission with the holding fixture
and holding fixture base.
Holding fixture: 5-8841-0841-0
Holding fixture base: 5-8840-0003-0

Remove the drain plug from the oil pan and drain the
ATF from the oil pan.

Rotate the automatic transmission so that the converte
r
housing is facing up and drain the ATF.

Rotate the automatic transmission so that the oil pan is
facing up.

Remove the 19 bolts and the oil pan.

UNIT REPAIR (JR405E) 7A4-13

Reassembly steps
Coat the parts with ATF before installing them.

11CV18

1. Control valve upper body
2. Control valve lower body
3. Separation plate
Assembly the control valve upper body, the lower body, and
the separation plate.
Tighten the bolts to the specified torque.



244L300002

7A4-14 UNIT REPAIR (JR405E)

Number Length (Color)
Control valve rocket
bolts and nuts (A) 2 (Plus 2 nuts) 50 mm (1.97 in) (Gold)
Upper body and
lower body fixing
bolts
(B) 2 45 mm (1.77 in) (Silver)
(C) 13 35 mm (1.38 in) (Silver)
Line pressure
solenoid fixing bolt
(D) 1 16 mm (0.63 in) (Gold)

Torque: 8 N




m (69 Ib




in)

7A4-16 UNIT REPAIR (JR405E)

12CV19

4. Solenoid
5. Oil pressure switch
Install the O-rings to each of the solenoids.

Install the 6 solenoids together and the 3 oil pressure
switchs.
NOTE:
Be sure the high clutch oil pressure switch is marked.

Tighten the bolts to the specified torque.
Torque:
Oil pressure switch bolts – 4.4 N






m (39 Ib






in)
Line pressure solenoid bolt (Single gold-colored bolt 16
mm) – 8 N






m (69 Ib






in)
6. Solenoid fixing plate
7. Harness bracket Install the solenoid fixing plate together with the harness
bracket.
Tighten the bolts to the specified torque.

Number Length (Color)
Solenoid fixing plate bolt
(A) 4 16 mm (0.63 in) (Gold)
(B) 7 45 mm (1.77 in) (Silver)

13CV20


Torque: 8 N






m (69 Ib






in)

14CV21



15CV26

8. Harness assembly
Install the harness assembly.

UNIT REPAIR (JR405E) 7A4-17
9. Oil strainer Install the oil strainer.
Tighten the bolts to the specified torque.

Number Length (Color)
Oil strainer bolt
(C) 9 13 mm (0.51 in) (Silver)
(D) 4 45 mm (1.77 in) (Silver)

16CV40


Torque: 8 N






m (69 Ib






in)

UNIT REPAIR (JR405E) 7A4-23

CONTROL VALVE LOWER BODY

10CV11
Legend
1. Retainer plate, spring, and steel ball
2. Retainer plate, plug, spring, and
pressure regulator valve
3. Retainer plate, spring, and high clutch
accumulator
4. Retainer plate, plug, low and reverse
brake fail valve A, and spring
5. Retainer plate, plug, spring, and fail
valve
6. Retainer plate, plug, low and reverse
brake amp valve, and spring
7. Oil pressure switch
8. Oil filter
9. Solenoid
10. Line pressure solenoid
11. Lock-up solenoid

12. Harness bracket
13. Solenoid fixing plate
14. Harness assembly
15. Retainer plate, plug, spring, and 2-4
brake fail valve A
16. Retainer plate, plug, spring, and low
clutch amp valve B
17. Retainer plate, spring, and torque
converter relief valve
18. Oil strainer
19. Control valve lower body
20. Retainer plate, spring, and 2-4 brake
solenoid accumulator
21. Oil pressure switch

7A4-26 UNIT REPAIR (JR405E)
No. Valve
nomenclature Diameter
(mm / in) Length
(mm / in)Configuration
14 Pressure relief ---- ----

15 Pressure
regulator 16.0 /
0.630 89.5 /
3.524
16 Low and reverse
brake fail (A) 10.0 /
0.394 52.0 /
2.047
17 Fail 12.0 /
0.472 53.5 /
2.106
18 Low and reverse
brake amp 12.0 /
0.472 55.5 /
2.185
19 2 – 4 brake fail
(A) 10.0 /
0.394 65.5 /
2.579
20 Low clutch amp
(B) 12.0 /
0.472 53.0 /
2.087
21 Torque
converter relief 10.0 /
0.394 37.4 /
1.472
22 2 – 4 brake
solenoid
accumulator 14.0 /
0.551 19.5 /
0.768
23 High clutch
accumulator 10.0 /
0.394 31.0 /
1.220

UNIT REPAIR (JR405E) 7A4-27

Spring specifications
No. Valve nomenclature Free length
(mm / in) Outside
diameter (mm
/ in) Linear
diameter (mm
/ in) Number of
coils
14 Pressure relief 49.0 / 1.929 7.6 / 0.299 1.1 / 0.043 17.3
15 Pressure regulator 30.5 / 1.201 14.0 / 0.551 1.4 / 0.055 5.7
16 Low and reverse brake fail (A) 22.0 / 0.866 7.0 / 0.276 0.6 / 0.024 10.0
17 Fail 23.0 / 0.906 11.0 / 0.433 0.5 / 0.020 13.2
18 Low and reverse brake amp 19.5 / 0.768 7.9 / 0.311 0.5 / 0.020 6.9
19 2 – 4 brake fail (A) 24.8 / 0.976 8.5 / 0.335 0.9 / 0.035 7.8
20 Low clutch amp (B) 26.0 / 1.024 11.0 / 0.433 0.5 / 0.020 6.9
21
Torque converter relief More than 47.2
/ 1.858 9.2 / 0.362 1.6 / 0.063 20.2
22 2 – 4 brake solenoid accumulator 31.4 / 1.236 9.8 / 0.386 1.3 / 0.051 9.3
23 High clutch accumulator 51.0 / 2.008 6.5 / 0.256 0.8 / 0.031 23.5

Oil pressure switch
Apply compressed air (392 kPa/4.0 kg/cm2) to the oil pressure
switch to check the oil pressure switch continuity between the
connector and screw.






244L300011

Oil temperature sensor (harness assembly)
Check the oil temperature sensor resistance between harness
terminals 7 and 6 (ground).

Oil temperature sensor resistance: 2,400




2,600 ohms
(20
 )


Solenoid
Measure the resistance of each solenoid.

Resistance:
Brown connector – 3.0
 3.4 ohms (20
 C)
Gray connector – 12.0
 13.2 ohms (20
 C)
White connector – 12.2
 13.4 ohms (20
 C)

Reassembly steps

Coat the parts with ATF before installing them.

Install the control valve to the control valve lower body.

Install the oil filter to the control valve lower body.