steering ISUZU TF SERIES 2004 Repair Manual

10-32 CAB
INSTALLATION


This illustration is based on RHD model
RTW4A0LF001101

Installation Steps
1. Cross beam
2. Instrument panel
3. Instrument harness assembly
4. Vent duct assembly/Defroster nozzle
assembly
5. Side ventilation grille
6. Passenger air bag
7. Glove box cover
8. Passenger lower bracket
9. Meter assembly
10. Ashtray bracket
11. Storage box assembly
12. Control lever assembly
13. Center cluster assembly


14. Ashtray case

15. Instrument panel & Cross beam
assembly
16. Side cover
17. Front cover
18. Front pillar trim cover
19. Dash side trim cover
20. Meter cluster assembly

21. Steering wheel/Steering cowl
22. Driver air bag
23. Driver knee bolster assembly
24. Instrument panel driver lower cover assembly
25. Glove box
26. Front console assembly

CAB 10-33
Important Operations
15. Instrument Panel & Crass Beam Assembly
1) Tighten the 4 bolts fixing the cross beam and body panel
to the specified torque.
Torque N
m (kgf
m/lb
ft)
19 (1.9/14)

2) A Bolt: Steering Column to Cross Beam
Torque N
m (kgf
m/lb
ft)
20 (2.0/14)
B Bolt: Pedal Bracket to Cross Beam
Torque N
m (kgf
m/lb
ft)
15 (1.5/11)


3) C Bolt: Parking Brake Bracket to Cross Beam
Torque Nm (kgfm/lbft)
15 (1.5/11)

21. Steering Wheel/Steering Cowl

Tighten the steering wheel fixing nut to the specified
truque.
Torque N
m (kgf
m/lb
ft)
35 (3.6/26)

8A-88 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION

This illustration is based on RHD model
STARTER SWITCH
Removal
1. Steering Lock Assembly

Refer to Section 3B" STEERING COLUMN" for steering
lock assembly removal steps.
2. Starter Switch




Installation
Follow the removal procedure in the reverse order to install the
starter switch.


INSPECTION AND REPAIR


STARTER SWITCH
Switch Connections
Terminal No.

Starter
switch key
position B-62
2
(B2)B-62
4
(ACC)B-62
1
(IG2) B-63
1
(ST) B-63
3
(B1)B-62
3
(IG1)
Removed

OFF
ACC Inserted
ON
START
LOCK

825R300046

Starter relay
Check continuity between the relay terminals.
1 - 4............................. No continuity
(When battery voltage is applied between 2 and 3)
1 - 4............................. Continuity

ELECTRICAL-BODY AND CHASSIS 8A-129
Installation
Follow the removal procedure in the reverse order to install the
headlight.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the headlight connector is securely
connected.
This will prevent a contact and an open circuit.

This illustration is based on RHD model

LIGHTING SWITCH
Removal
1. Disconnect the battery ground cable.
2. Remove the steering wheel
1.
Refer to the “STEERING” Section of this manual.
3. Remove the Instrument panel lower cover
2.
4. Remove the steering column cover
3.


This illustration is based on RHD model
5. Disconnect the connector.
6. Remove the lighting switch from the steering shaft.





Installation
Follow the removal procedure in the reverse order to install the
lighting switch.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the lighting switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


Wire Harness
Do not pinch the wire harnesses between the cluster and the
meter hood during the cluster installation procedure.
Wire damage will result.

ELECTRICAL-BODY AND CHASSIS 8A-131


LICENSE PLATE LIGHT
Removal
1. Remove the lens cover 1 and the connector 2.
2. Pull the bulb
3 to remove it.



Installation
Follow the removal procedure in the reverse order to install the
license plate light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the license plate light bulb is correctly
installed.
This will prevent a poor contact and open circuit.



HEADLIGHT BEAM SWITCH
(COMBINATION SWITCH)
Removal
1. Disconnect the battery ground cable.
2. Remove the screws on the lower part of the steering wheel.
3. Remove the horn pad.
4. Remove the wiring connector.
5. Remove the steering wheel fixing nuts.
6. Remove the steering wheel.
Refer to the "STEERING" Section of this manual.
7. Remove the Instrument panel lower cover.
8. Remove the steering column cover.
9. Disconnect the connector.
10. Remove the headlight beam switch (lever) from the steering
shaft (combination switch).


Installation
Follow the removal procedure in the reverse order to install the
headlight beam switch (lever).
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the headlight beam switch connector is
securely connected.
This will prevent a poor contact and an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-171
HORN
1. Both sides of horn do not sound

Checkpoint Trouble Cause Countermeasure



Repair the grounding point

Poor ground contact
NG

Horn relay


Grounding point


Reinstall or replace fuse No.
EB-15 (10A)

Fuse No EB-15 (10A, Relay
and fuse box)

Poor fuse contact or blown
fuse
NG
OK OK

Reinstall or replace the horn
relay

Poor relay contact or faulty
horn relay
NG
Voltage between connector
3
X-3 - ground or 1 X-3
- ground (Should be battery
voltage present) OK

Repair open circuit or
reconnect the connector
Open circuit or poor connector
contact between fuse No. EB-
15 (10A) and horn relay
NG

Remove steering pad and
steering wheel
OK

Horn switch continuity
OK
Repair or replace the horn
switch

Poor switch point contact or
faulty switch
NG
Continuity between
4
X-3 - 10 B-60
2
X-3 - 1 C-20 (1 C-21) OK

Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG

8A-176 ELECTRICAL-BODY AND CHASSIS
This illustration is based on RHD model
TURN SIGNAL SWITCH
Removal
1. Disconnect the battery ground cable.
2. Remove the steering wheel
1.
Refer to the “STEERING” Section of this Manual.
3. Remove the instruments panel lower cover
2.
4. Remove the steering column cover
3.

This illustration is based on RHD model
5. Disconnect the connector.
6. Remove the turn signal switch from the steering shaft.




Installation
Follow the removal procedure in the reverse order to install the
turn signal switch (lever).
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the turn signal switch connector is
securely connected.
This will prevent a poor contact and at an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-179

HORN SWITCH
Removal
1. Disconnect the battery ground cable.
2. Disable the SRS (Refer to “Disabling the SRS”in this
section).
3. Check the both side hole of the steering cover.


4. Check the position of the pins in a hole. Push the pin in the
direction of an arrow.


5. Push the four pins at 56 mm bar.

6. Cancel the lock four pins.
7. Disconnect the SRS air bag connector and horn lead
connector located behind the air bag assembly and remove
the air bag assembly.

Installation
1. Connect the SRS bag connector and horn lead connector.
2.
Align the each snap stud of driver air bag to the hole of
steering wheel.

8B-6 CRUISE CONTROL SYSTEM
Adjustment
1. Check to be sure that the brake pedal has been completely
returned by the return spring.
2. Disconnect the switch connector.



RTW3A0SH001201

3. Release the lock (2) by turning the switch (1) counter-clock-
wise.
4. After doing so, pull the pedal arm (3) to you a little so tha
t
the pedal arm is not pushed in.
5. Making the pedal arm not movable with one hand, push in
the whole switch with the other hand until the plunger of the
switch is pushed in and the switch itself hits the rubber o
f
the pedal arm.
In the condition, turn the switch clock-wise until "click"
sound is made and lock it.
By doing this, the switch is adjusted at 0.2 to 1.2mm (0.01-
0.06 in.) clearance.

Clutch Switch


Removal and Installation
Refer to the Clutch Control removal and installation steps in
Clutch section.

Adjustment
1. Turn the clutch switch or stopper bolt 1 until the switch bolt
or stopper bolt just touches the clutch pedal arm.
2. Adjust clutch switch or stopper bolt by backing it out half a
turn, and measure the clearance (L) between the clutch
pedal arm and the clutch switch bolt end or stopper bolt.
3. Lock the lock nut
2.
4. Connect the clutch switch connector.

Clutch switch and clutch and clutch pedal clearance
mm (in)

Limit 0.5-1.5 (0.020-0.059)


Starter Switch

431R300001
Removal
1. Steering Lock Assembly

Refer to the Steering Lock assembly removal steps o
f
"Steering Column" in Power-Assisted Steering System
section.
2. Starter Switch

Installation
Follow the removal procedure in the reverse order to install the
starter switch.

ENGINE MECHANICAL 6A – 39

18. Radiator
1) Drain the engine coolant.
2) Remove the reservoir hose.
3) Remove the upper and lower hose.
4) Remove the fan guide.
5) Remove the radiator.


19. Fan

P1010034
20. Air cleaner
1) Remove the MAF sensor connector (4JA1TC/4JH1TC) from air cleaner duct.
2) Remove the air cleaner duct and the air cleaner box from engine room.
3) Remove the two air ducts from inter cooler (4JA1TC/4JH1TC).

21. Power Steering Pump Loosen the power steering pump adjust plate bolt, then
remove the power steering pump assembly. Place the
power steering pump assembly along with piping on the
body side.
22. Air conditioner compressor 1) Remove air compressor magnet connector.
2) Remove the air conditioner compressor. Place the air conditioner compressor along with piping on the body
side.
23. Engine Control Cable Remove the engine control cable from its bracket
(4JA1TC/4JH1TC) or the injection pump (4JA1T(L)).

24. Vacuum Piping Remove the vacuum pipe from the vacuum pump, the
EGR valve, injection pump FICD (4JA1T(L)).

25. Engine Harness 1) Remove following connectors from engine.

TPS connector

Oil pressure switch connector

Thermo switch connector

Injection pump connector

Engine earth

Thermometer unit connector

TDC sensor
2) Remove the clips fixing engine harness.
P1010009