warning JAGUAR S TYPE 2005 1.G Electrical Manual

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 08.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DUAL SOLAR SENSOR (AUTO HEADLAMP) SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FRONT FOG LAMP – LH BF4 2-WAY / BLACK FRONT BUMPER, LH SIDE
FRONT FOG LAMP – RH BF5 2-WAY / BLACK FRONT BUMPER, RH SIDE
FRONT FOG LAMP RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R11
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HEADLAMP UNIT – LH HL2 2-WAY / BLACK ENGINE COMPARTMENT, LH FRONT
HL3 2-WAY / BLACK
HL4 2-WAY / BLACK
HL7 3-WAY / GREY
HL8 2-WAY / BLACK
HEADLAMP UNIT – RH HR2 2-WAY / BLACK ENGINE COMPARTMENT, RH FRONT HR3 2-WAY / BLACK
HR4 2-WAY / BLACK
HR7 3-WAY / GREY
HR8 2-WAY / BLACK
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
SIDE MARKER – LH BF2 2-WAY / BLACK FRONT BUMPER, LH SIDE
SIDE MARKER – RH BF3 2-WAY / BLACK FRONT BUMPER, RH SIDE
TURN REPEATER – LH FH62 2-WAY / BLACK LH FRONT FENDER
TURN REPEATER – RH FH76 2-WAY / BLACK RH FRONT FENDERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationBF1 6-WAY / GREY / FRONT HARNESS TO FRONT BUMPER HARNESS BEHIND FRONT BUMPER, LH SIDE
FH39 12-WAY / GREY / FRONT HARNESS TO RH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, RH SIDE
FH40 12-WAY / GREY / FRONT HARNESS TO LH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, LH SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicO FH9–7 LH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–11 RH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH9–19 RH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–22 LH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDÅ
S FH59–1 SCP –
O FH59–2 LH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH59–5 FRONT FOG LAMP RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
O FH59–10 RH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH59–12 POWER GROUND: GROUND
O FH60–4 RH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–5 LH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–7 RH DIP BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH60–8 LH DIP BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH60–10 RH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND
O FH60–17 LH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDInstrument Cluster
Pin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
O FC8–22 HAZARD INDICATOR: PULSED B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–3 MAIN LIGHTING SWITCH SIGNALS – MAIN, FLASH: VARIABLE RESISTANCE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
I FC9–6 MAIN LIGHTING SWITCH SIGNALS – TURN SIGNALS, HAZARD WARNING: TURN = VARIABLE RESISTANCE; HAZARD = GROUND
I FC9–7 AUTOLAMP SENSOR SIGNAL: VARIABLE RESISTANCE
I FC9–8 FOG LAMPS SWITCH SIGNAL: VARIABLE RESISTANCE
SG FC9–9 AUTOLAMP SENSOR GROUND: GROUND
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 08.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DUAL SOLAR SENSOR (AUTO HEADLAMP) SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FRONT FOG LAMP – LH BF4 2-WAY / BLACK FRONT BUMPER, LH SIDE
FRONT FOG LAMP – RH BF5 2-WAY / BLACK FRONT BUMPER, RH SIDE
FRONT FOG LAMP RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R11
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HEADLAMP UNIT – LH HL2 2-WAY / BLACK ENGINE COMPARTMENT, LH FRONT
HL3 2-WAY / BLACK
HL4 2-WAY / BLACK
HL6 (HID) 2-WAY / WHITE
HL7 3-WAY / GREY
HL8 2-WAY / BLACK
HEADLAMP UNIT – RH HR2 2-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
HR3 2-WAY / BLACK
HR4 2-WAY / BLACK
HR6 (HID) 2-WAY / WHITE
HR7 3-WAY / GREY
HR8 2-WAY / BLACK
HID RELAY – LH — — FRONT POWER DISTRIBUTION FUSE BOX – R10
HID RELAY – RH — — FRONT POWER DISTRIBUTION FUSE BOX – R13
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
SIDE MARKER – LH BF2 2-WAY / BLACK FRONT BUMPER, LH SIDE
SIDE MARKER – RH BF3 2-WAY / BLACK FRONT BUMPER, RH SIDE
TURN REPEATER – LH FH62 2-WAY / BLACK LH FRONT FENDER
TURN REPEATER – RH FH76 2-WAY / BLACK RH FRONT FENDERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationBF1 6-WAY / GREY / FRONT HARNESS TO FRONT BUMPER HARNESS BEHIND FRONT BUMPER, LH SIDE
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEM
FH39 12-WAY / GREY / FRONT HARNESS TO RH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, RH SIDE
FH40 12-WAY / GREY / FRONT HARNESS TO LH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, LH SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicO CA31–20 LH HID RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDÅ
O FH9–6 RH HID RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH9–7 LH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–11 RH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH9–19 RH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–22 LH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDÅ
S FH59–1 SCP –
O FH59–2 LH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH59–5 FRONT FOG LAMP RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
O FH59–10 RH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH59–12 POWER GROUND: GROUND
O FH60–4 RH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–5 LH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–10 RH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND
O FH60–17 LH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDInstrument Cluster
Pin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
O FC8–22 HAZARD INDICATOR: PULSED B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–3 MAIN LIGHTING SWITCH SIGNALS – MAIN, FLASH: VARIABLE RESISTANCE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
I FC9–6 MAIN LIGHTING SWITCH SIGNALS – TURN SIGNALS, HAZARD WARNING: TURN = VARIABLE RESISTANCE; HAZARD = GROUND
I FC9–7 AUTOLAMP SENSOR SIGNAL: VARIABLE RESISTANCE
I FC9–8 FOG LAMPS SWITCH SIGNAL: VARIABLE RESISTANCE
SG FC9–9 AUTOLAMP SENSOR GROUND: GROUND
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 08.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DUAL SOLAR SENSOR (AUTO HEADLAMP) SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
HIGH-MOUNTED STOP LAMP CA18 3-WAY / GREY PARCEL SHELF, CENTER
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
LICENSE PLATE LAMPS CA66 4-WAY / BLACK LUGGAGE COMPARTMENT LID CA67 2-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REVERSE SWITCH GB5 2-WAY / BLACK TRANSMISSION, LH REAR
SIDE MARKER LAMP – LH BR6 2-WAY / BLACK REAR BUMPER, LH SIDE
SIDE MARKER LAMP – RH BR7 2-WAY / BLACK REAR BUMPER, RH SIDE
TAIL LAMP UNIT – LH CA10 7-WAY / BLACK LUGGAGE COMPARTMENT, LH REAR
TAIL LAMP UNIT – RH CA68 7-WAY / BLACK LUGGAGE COMPARTMENT, RH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationBR1 10-WAY / GREY / CABIN HARNESS TO REAR BUMPER HARNESS BEHIND REAR BUMPER, RH SIDE
FC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationCA116 BEHIND REAR SEAT BACK, RH SIDE
CA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH4 (DIESEL ONLY) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Instrument Cluster Pin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
I FC8–7 REVERSE SWITCH SIGNAL: REVERSE = GROUND
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
O FC8–22 HAZARD INDICATOR: PULSED B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–3 MAIN LIGHTING SWITCH SIGNALS – MAIN, FLASH: VARIABLE RESISTANCE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
I FC9–6 MAIN LIGHTING SWITCH SIGNALS – TURN SIGNALS, HAZARD WARNING: TURN = VARIABLE RESISTANCE; HAZARD = GROUND
I FC9–7 AUTOLAMP SENSOR SIGNAL: VARIABLE RESISTANCE
I FC9–8 FOG LAMPS SWITCH SIGNAL: VARIABLE RESISTANCE
SG FC9–9 AUTOLAMP SENSOR GROUND: GROUND
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –Rear Electronic ModulePin Description and CharacteristicO CA63–1 RH STOP LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–2 LH STOP LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–3 LH REAR TURN SIGNAL ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND (PULSED)
O CA63–4 RH REAR TURN SIGNAL ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND (PULSED)
O CA63–5 RH TAIL LAMPS ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–6 LH TAIL LAMPS ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–7 LH REAR FOG LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–8 RH REAR FOG LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–9 LH REVERSE LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–10 RH REVERSE LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA63–17 HIGH-MOUNTED STOP LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA100–5 LICENSE PLATE LAMPS ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA100–6 LH REAR SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
O CA100–12 RH REAR SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–13 BRAKE ON / OFF SWITCH (NORMALLY OPEN): OPEN CIRCUIT / B+
PG CA103–11 POWER GROUND: GROUND
PG CA103–12 POWER GROUND: GROUND
PG CA103–25 POWER GROUND: GROUND
PG CA103–26 POWER GROUND: GROUND

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 12.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationACTIVE SECURITY SOUNDER AT4 3-WAY / BLACK ENGINE COMPARTMENT, REARWARD OF RH HEADLAMP UNIT
AUDIO UNIT FC94 20-WAY / BLACK CENTER CONSOLE
FC96 ANTENNA CONNECTOR
FC108 FIBER OPTIC CONNECTOR
DOOR LATCH ASSEMBLY – DRIVER DT5 10-WAY / BLACK DRIVER DOOR
DOOR LATCH ASSEMBLY – LH REAR CA81 10-WAY / BLACK LH REAR DOOR
DOOR LATCH ASSEMBLY – PASSENGER PT3 10-WAY / BLACK PASSENGER DOOR
DOOR LATCH ASSEMBLY – RH REAR CA90 10-WAY / BLACK RH REAR DOOR
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HOOD AJAR SWITCH FH21 2-WAY / BLACK ENGINE COMPARTMENT, ADJACENT TO RH SUSPENSION TURRET
HORN RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R12
HORNS FH29 2-WAY / BLACK FORWARD OF RADIATOR
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INCLINATION SENSOR CA173 4-WAY / GREY LUGGAGE COMPARTMENT, LH REAR
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL
FC9 32-WAY / BLACK
PASSIVE ANTI-THEFT SYSTEM TRANSCEIVER FC52 4-WAY / GREEN STEERING COLUMN, IGNITION SWITCH
PASSIVE SECURITY SOUNDER AT2 1-WAY / BLACK ENGINE COMPARTMENT, REARWARD OF RH HEADLAMP UNIT
AT3 1-WAY / BLACK
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REMOTE KEYLESS ENTRY MODULE CA303 4-WAY / BLACK UNDER CENTER CONSOLE
ROOF CONSOLE CA250 22-WAY / BLACK ROOF HEADLINER
SECURITY INDICATOR SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
STEERING COLUMN LOCK MODULE FC59 4-WAY / BLACK ADJACENT TO STEERING COLUMN LOCK
TRUNK LID LATCH ASSEMBLY CA26 4-WAY / BLACK LUGGAGE COMPARTMENT LIDHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
DT10 10-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC39 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEM
FH89 4-WAY / GREY / FRONT HARNESS TO ALARM LINK ADJACENT TO FRONT POWER DISTRIBUTION FUSE BOX
PT1 14-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR TRIM HARNESS PASSENGER DOOR
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
CA158 LUGGAGE COMPARTMENT, LH SIDE REAR CORNER
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Audio Unit Pin Description and CharacteristicO FC94–8 SECURITY SYSTEM GROUND SENSING: GROUND WHEN AUDIO UNIT INSTALLEDDriver Door ModulePin Description and CharacteristicI CA85–2 LOCK / UNLOCK STATUS SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA85–3 SCP +
S CA85–4 SCP –
PG CA85–8 POWER GROUND: GROUND
PG CA85–9 REMOTE KEYLESS ENTRY MODULE GROUND: GROUND
I CA85–10 DOUBLE LOCK STATUS SWITCH (N ORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
B+ CA85–12 SWITCHED SYSTEM POWER SUPPLY: B+
O DT2–6 REMOTE KEYLESS ENTRY MODULE POWER SUPPLY: B+
O DT2–8 LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–9 UNLOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–10 DOUBLE LOCK DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
D DT2–13 REMOTE KEYLESS ENTRY MODULE SIGNAL: ENCODED COMMUNICATIONS
I DT2–16 DRIVER DOOR ALARM SET / LOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I DT2–17 DRIVER DOOR ALARM RESET / UNLOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
D DT2–18 REMOTE KEYLESS ENTRY MODULE SIGNAL: ENCODED COMMUNICATIONSFront Electronic Module
Pin Description and CharacteristicI CA24–15 PASSENGER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA31–3 IGNITION SWITCHED VOLTAGE SIGNAL (II): B+
I CA31–5 REM SECURITY GROUND SENSE: OPEN CIRCUIT IF REM REMOVED
I CA31–7 AUDIO UNIT SECURITY GROUND SENSE: OPEN CIRCUIT IF AUDIO UNIT REMOVED
I CA31–8 DRIVER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA31–18 INTRUSION AND INCLINATION SENSORS SIGNAL: GROUND (PULSED)
O FH9–16 INTRUSION AND INCLINATION SENSORS SUPPLY VOLTAGE: B+
S FH59–1 SCP –
I FH59–3 HOOD AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
O FH59–8 HORN RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
O FH60–3 ACTIVE SECURITY SOUNDER ACTIVATE: ENCODED COMMUNICATION
O FH60–4 RH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–5 LH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
PG FH60–6 STEERING COLUMN LOCK CONTROL MODULE POWER GROUND SUPPLY: GROUND
PG FH60–11 POWER GROUND: GROUND
O FH60–16 PASSIVE SECURITY SOUNDER ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO B+Instrument Cluster
Pin Description and CharacteristicO FC8–1 SECURITY INDICATOR DRIVE: ACTIVE = PULSED GROUND
PG FC8–2 POWER GROUND: GROUND
I FC8–5 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
B+ FC8–14 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–32 SIGNAL GROUND: GROUND
D FC9–16 PATS TRANSCEIVER: ENCODED COMMUNICATION
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –
I FC9–31 PATS GROUND: GROUND
D FC9–32 PATS TRANSCEIVER: ENCODED COMMUNICATIONRear Electronic ModulePin Description and CharacteristicO CA63–3 LH REAR TURN SIGNAL ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND (PULSED)
O CA63–4 RH REAR TURN SIGNAL ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND (PULSED)
O CA100–1 STEERING COLUMN LOCK CONTROL MODULE SUPPLY VOLTAGE: B+
B+ CA101–3 BATTERY POWER SUPPLY: B+
O CA101–5 REM SECURITY GROUND SENSE: OPEN CIRCUIT IF REM REMOVED
I CA101–17 LHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–14 TRUNK AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
B+ CA103–13 SWITCHED SYSTEM POWER SUPPLY: B+
I CA103–16 LHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND

Wash / Wipe System
Jaguar S-TYPE 2005
Wash / Wipe System
Fig. 13.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f13_1_200045
FH60-11
B
P
FH77
WR
Y
GW
CA248-6 CA248-3
W
CA248-1
FC118-4
FHS16
CA31-2
BWWU
YU
FH36-2
FH36-1
FH17-3
FH17-1
NR
FH22
(FH42)
FH42
FC118-6
FC118-5
WRY
GW
CA31-14
CA31-13
CAS9
CAS10
CAS11
FC19-16 FC19-15 FC19-14
WR
Y
GW
II
CA248-12
Y
GW
WR
O
FH9-14
NW
YG
555354
NG
NR
R
RG
BG
O
FH59-4
O
FH9-1
O
FH9-3
B
FH38-2
FH38-1
FH9-15
FH37-1
FH37-2
B
I
FH59-1
U
FH59-7
Y
20.220.2
SS
BG
I
BG
FH9-13
FH17-2
FH17-5
FH17-4
B
NR
Y
YU
51
52
WB
CA248-11
NR
FH60-1
S60
B
NR NR
NR
261R261R261R1K3562R332R200R121R100R
100R261R261R
261R
261R
RF14-2 RF14-1
YB WB
RF14-3
YB
RF34-12
RF34-13
RF34-14
CA248-8
BG
BCA248-7
YB
CA248-10
YB
CA248-9
PB
24IICA116
1I
32
51
R18
4
32
51
R15
4
32
51
R16
4
56
FH1-17
BG
WIPER
MODE SELECT
WIPER
DELAY/WASH
RAIN SENSING MODULE *
RAIN SENSING UNIT *
* NOTE:
Rain sensing system – rain sensing vehicles only.
WIPE / WASH SWITCH
FLUID LEVEL WARNING;
VEHICLE SPEED
FRONT ELECTRONIC MODULE WIPER HIGH / LOW RELAY
WIPER PARK RELAY
POWER WASH RELAY
FRONT POWER DISTRIBUTION FUSE BOX WASHER FLUID LEVEL SWITCH
WINDSHIELD WASHER PUMPPOWER WASH PUMP
WIPER MOTOR ASSEMBLY
PARK
RUN
LOW SPEED
HIGH SPEED
F21 5A
FH32-18
FH32-27
VARIANT:
All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004

Advanced Restraint System: Part 1
Jaguar S-TYPE 2005
Advanced Restraint System: Part 1
Fig. 17.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f17_1_200045
RW
DM20-3
B
CA141
(CA154) CA22-2
CA114-5
WU
CA114-12CA114-16
B
CA14
CA232-23
UY37II
CA114-19
BG
O
DB4-2
DB4-1
RW
BW
DM40-2
DM40-1
RW
BW
CA226-2
CA226-1
O
OYYR
YR
FC117-2FC117-1
Y
Y
FC117-10FC117-9
07.1
CA114-17
WB
O
16.3
16.4
CA114-22
WB
O
CA114-11
W
20.2
D
DM20-4
CA232-25
BRU
PN15-3
PNS5
B
CA154
(CA141)
PN15-4 CA232-26
CA114-15
O
CA22-1CA232-27
WR
CA232-28
NR
CA58-2CA58-1CA232-29
WU
CA232-30
NG
FH102-2
N
FH102-1
W
CA232-19
N
CA232-20
W
FH2-15FH2-16
CA232-24
U
DM41-2
DM41-1
CA114-6
CA114-1
CA114-2
CA232-3CA232-4CA232-1CA232-2
PB4-2
PB4-1
RW
BW
PN35-2
PN35-1
RW
BW
CA228-2
CA228-1
YR
YG
CA232-5CA232-6CA232-21CA232-22
CA232-13
O
CA232-14
YR
CA230-2
CA230-1
CA232-15
U
CA232-16
BO
CA246-2
CA246-1
BP
HH
H
07.1
DM23-3
DM23-7
UY
U
DM23-16
RW
B
DMS6
DM23-1
B
PN24-16
RU
PN24-1
B
BR
FC42-1
FC42-2
YR
YR
Y
Y
FC42-3
FC42-4DM40-4
DM40-3
O
OY
CA232-31CA232-32
DM20-2
DM20-1
O
OY
PN35-4
PN35-3
OY
OG
CA232-33CA232-34
PN15-2
PN15-1
OY
OG
CA225-2
CA225-1
BR
BW
CA232-35CA232-36
CA224-2
CA224-1
BO
BK
CA232-39CA232-40
CA223-2
CA223-1
BG
UY
CA232-37CA232-38
17.2
16.2
16.1
SW10-1
SW10-2
SW9-1
SW9-2 SW12-1
SW12-2
SW11-1
SW11-2
NB
SW
SB
NR
FRONT IMPACT SENSOR
DRIVER SIDE IMPACT SENSOR
DRIVER REAR SIDE IMPACT SENSOR
DRIVER SEAT POSITION SWITCH
DRIVER SEAT BELTSWITCH
PASSENGER SEAT BELT SWITCH
PASSENGER SIDE IMPACT
SENSOR
PASSENGER REAR SIDE IMPACT
SENSOR
SERIAL COMMUNICATION
TELEPHONE / JAGUARNET: AIRBAG DEPLOYED (CIRCUIT CONTINUED)
INSTRUMENT CLUSTER: AIRBAG WARNING (CIRCUIT CONTINUED)
INSTRUMENT CLUSTER: SEAT BELT AUDIBLE WARNING (CIRCUIT CONTINUED)
PASSENGER AIRBAG DEACTIVATION LAMP
RESTRAINTS CONTROL MODULE (CONTINUED Fig 17.2) PASSENGER SIDE REAR SEAT BELT
PRETENSIONER IGNITER CENTER REAR SEAT BELT
PRETENSIONER IGNITER
DRIVER SIDE REAR SEAT BELT
PRETENSIONER IGNITER PASSENGER SEAT BELT
PRETENSIONER IGNITER DRIVER SEAT BELT
PRETENSIONER IGNITER
PASSENGER SIDE
AIRBAG IGNITER DRIVER SIDE AIRBAG
IGNITER
PASSENGER CURTAIN
AIRBAG IGNITER DRIVER CURTAIN AIRBAG
IGNITER DRIVER DUAL AIRBAG
IGNITERS
CASSETTE
CASSETTE
CASSETTE
CASSETTE
STAGE
TWO
STAGE ONE
VARIANT: All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004

xivDATE OF ISSUE: May 2004
AppendixJaguar S-TYPE 2005
CAN Message Matrix
FFH warning lamp requestRT
FFH water temperature RR T
Follow speed RR T
Follow warning light RT
Front fog status RR T
Front passenger seat heat power status RR T
Fuel cap warning TR
Fuel level damped RR T
Fuel level raw 1 RR T
Fuel level raw 2 RR T
Fuel level status TR
Fuel low level raw RT
Fuel pump status RT
Fuel used TT R
Gear position actual RR T R
Gear position selected RR T R R R
Gear position target RR T R
Gear selection fault RR T R
Glow plug status TR
Headway increment TT R
Headway setting RT
IC ASC enable RR T R
Idle neutral control RR T
Idle neutral control state RT
Idle neutral disable TR
In gear T
Indicated engine torque TTR R
Indicator left TR
Indicator right TR
Inertia switch status TR
Intermediate position fault RT
J-GATE fault RRR T
CAN Message (R = Message Received; T = Message Transmitted)
ECM PCM
TCM
CCM IC
DSCM SCM
HLCM JGM
EPBM
FFHM
TPMM DIAG

DATE OF ISSUE: May 2004xv
AppendixJaguar S-TYPE 2005
CAN Message Matrix
J-GATE position selectedRT
J-GATE selection fault RR T R
Kickdown TTR
Lateral acceleration signal RTR
Main beam status RR T
Natural light TR
OBDII clear fault codes TR R
OBDII DSC clear acknowledge RT
OBDII TCM clear acknowledge RT
Odo rolling count RT
Odometer reading RRRRT R
Oil service time expired TR
Parkbrake status RRR RR T
Pedal position TTRRRR
Performance mode indication TR
Performance mode switch RT
Powertrain configuration TTR R
Pressure transducer TT R
Rear fog status RR T
Reset service counters RT
Restricted a/c blowers RT
Reverse gear manual selected RR T
Set speed TTR R
Sidelight status RR T
Steering wheel angle RTR R
Steering wheel speed TR
Supercharged fuel pump warning TR
Target speed TT R
TCM configuration flag T
TCM fault code MIL status RT
TCS brake control RR R T
TCS engine torque control RR R T
CAN Message (R = Message Received; T = Message Transmitted)
ECM PCM
TCM
CCM IC
DSCM SCM
HLCM JGM
EPBM
FFHM
TPMM DIAG

xviDATE OF ISSUE: May 2004
AppendixJaguar S-TYPE 2005
CAN Message Matrix
TCS switch statusRRR R T
Temporary torque request RR T
Throttle malfunction amber TT R
Throttle malfunction red TT R
Throttle position TTR
Torque conv mult T
Torque converter slip RT
Torque converter status RT
Torque reduction request RR T
TPM comfort pressure RT
TPM RF echo 1 TR
TPM RF echo 2 TR
TPM system flat RT
TPM warning light RT
Traction acknowledge TT R
Traction shift map RT
Transmission fault codes RT
Transmission fluid pump pickup torque RT
Transmission fluid temperature RR T R
Transmission input indicated torque TTR
Transmission input speed RR T
Transmission malfunction RTRR
Transmission output speed RR T
Transmission pickup torque RT
Transmission shift map RR T R
Transmission torque limit RR T
Trip units RR T R
Tyre battery fl RT
Tyre battery fr RT
Tyre battery rl RT
Tyre battery rr RT
Tyre pressure fl RT
CAN Message (R = Message Received; T = Message Transmitted)
ECM PCM
TCM
CCM IC
DSCM SCM
HLCM JGM
EPBM
FFHM
TPMM DIAG