Key JAGUAR XJ 2004 X350 / 3.G Owner's Manual

3 - 4 Before Driving
Head Restraint Adjustment
!WARNING:
Adjust the head restraint so that it is
just behind your head and never
behind your neck.
All headrests may be manually tilted,
except those fitted with rear display
screens. Rear head restraint adjustment
The rear head restraints on vehicles
without electrically operated rear seats
may be manually adjusted.
To raise the outer rear seat headrests,
pull the headrest upwards. To lower,
press the lever in the escutcheon (shown
in the upper illustra
tion) and push the
headrest into the seat back.
Rear Seat Adjustment
Seats with individual backrests may be
adjusted electrically using the switches on
the sides of the seat cushions. Adjustment
can be made with or without the ignition
key inserted.
Seat adjustments are:
( A ) – Backrest recline and headrest
height.
( B ) – Adjustable lumbar support in the
lower backrest: Increase/decrease
support and up/down movement, as for
front seats.
For increased comfort, the front
passenger seat fore and aft movement
and backrest recline can be controlled
from the rear seat immediately behind,
using switch ( C). Note:
Operation of the front seat by a
rear seat passenger and rear seat
operation, except for lumbar adjustment,
can be disabled from the driver’s door
switchpack window and rear feature
immobilisation switch (see page 4 - 30).

3 - 6 Before Driving
Pedal Adjustment
!WARNING:
Do not adjust the pedals whilst driving.
This facility enables the pedals to be moved towards or away
from the driver’s seat, providing extra adjustment for the driving
position. All pedals move together (no individual pedal
adjustment) and are electrically controlled from the combined
steering column/pedal adjust switch on the left side of the
steering column housing. The adjustment can be made with or
without the ignition key inserted.
To adjust the position of the pedals, turn the switch
to ‘PEDALS’, then push it forwards or rearwards to cause a
corresponding movement of the pedal assembly.
Three pedal positions may be stored and recalled by the driver
position memory system. See Memory Setting on page 3 - 31.
It will not be possible to adjust the pedals if cruise control has
been set.

Before Driving 3 - 7
Steering Column
Adjustment
!WARNING:
Do not adjust the steering column
whilst driving.
The steering column can be adjusted for
tilt and reach by operating the rotary/
joystick control switch (A ) on the left side
of the steering column.
1. Turn the switch to the ‘COLUMN’ or ‘AUTO’ position.
2. Move the switch forwards or backwards to adjust reach.
3. Move the switch up or down to tilt.
Three column positions may be stored
and recalled by the driver position
memory system. See Memory Setting
on page 3 - 31.
Entry/exit mode
Entry/exit mode provides automatic
movement of the steering column and
driver’s seat to allow easier entry to or
exit from the vehicle.
Entry/exit mode is selected by setting the
steering column adjustment switch to the
‘AUTO’ position ( B). Exit
– If the ignition key is in position ‘0’
and the driver’s door is opened or if the
ignition key is removed, the steering
column will move to the uppermost tilt
position. The seat will move rearwards
unless it is already 1.5 inches (4 cm) or
less from its fully rearward position when
it will not move any further back.
Entry – When the key is next inserted in
the ignition switch and the door is closed,
the steering column and seat will return
to their previous positions. If, however,
the memorised driver position has been
changed (using the door memory switch
or another integrated key), the steering
wheel and seat will move to the new
position. Caution: Do not use steering wheel
mounted security devices since
movement of the steering wheel in
entry/exit mode could result in
vehicle damage (e.g. the windscreen)
or possible injury to the occupant.
Note:
1. If the adjustment switch is moved
away from ‘AUTO’ whilst the steering
column is tilted away, the steering
column will move back to its
memorised position when the key is
next inserted in the ignition and
entry/exit mode is then cancelled.
2. If the adjustment switch is moved during entry/exit operation, steering
column movement will stop.

Before Driving 3 - 31
Memory Setting
This facility enables three different
comfort positions to be memorised and
recalled for each occupant:
• The driver’s seat, steering column, pedals and exterior rear view mirrors.
• Rear passenger seat positions when memory is fitted to these.
The key does not have to be in the
ignition switch to make seat, steering
column and pedal adjustments but is
required to be in th e switch to set the
memory. Setting a memorised position
To store a driver’s seat position in the
memory:
1. Adjust the seat, steering column,
pedals and exterior rear view mirrors
to the desired positions.
2. Insert a key into the ignition switch and leave in the OFF position.
3. Push memory button M and the red LED in the switchpack will
illuminate for a five second period.
4. While the red LED is illuminated, push button ‘1’, ‘2’ or ‘3’ to memorise the
configuration. The LED will go out and
a chime will indicate that the setting
procedure is complete.
By repeating these three steps and
pressing the unused buttons, two more
driving positions can be stored in the
memory.
To set a new driving position, adjust to
the desired position and perform steps 2
and 3. The previous memory will be
erased and the new position will be set.
The rear passenger’s seats can also be
memorised by repeating steps 2 and 3
above after adjusting the seat to the
desired position. Recalling a memorise
d position from
the door switchpack
Ensure the gear selector lever is in
position ‘P’.
Press and release the appropriate
memory button (‘1’, ‘2’ or ‘3’). The seat,
steering column, pedals and door mirrors
will move automatically to the
memorised position.

3 - 32 Before Driving
Memory recall using an integrated
key
The integrated key will recall a memory
position when the unlock button is
pressed when set as follows:
1. Adjust the seat, steering column, pedals and exterior rear view mirrors
to the desired positions.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press button ‘1’, ‘2’ or ‘3’ and then press any button on the integrated
key. Both button presses must occur
while the red LED is illuminated.
4. Repeat for the other integrated key, pressing the remaining memory
buttons.
To cancel integrated key memory recall:
1. Place a key into the ignition switch and leave in the OFF position.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press any button on the integrated key
(except the panic button, if fitted) then
press the M button again. Both button
presses must occur while the red LED
is illuminated. Note:
If memory recall is performed
using an integrated ke y with the vehicle in
entry/exit position, the steering column
and seat will not return to the memorised
position until either the integrated key is
placed in the ignition switch or the
driver’s door is closed.
Driving position memory system
operating tips
• When making adjustments to a set driving position, reset the new
position in the same memory channel.
• A driving position will only be memorised during the five second
period when the red memory LED is
illuminated.
• Previous memory is erased when a new driving position is entered.
Clock Adjustment
The analogue clock is adjusted by
pressing the (+) and (–) buttons below
the dial. Pressing and holding either
button will increase the rate of hand
movement forwards or backwards as
required.

4-10 On the Road
Audible Warnings
Various sounds are produced for warning and notification purposes as follows:
Hazard or Condition Remedy/chime or tone
Air bag system failure. A tone sequence is repeated five times. Report the fault to a Jaguar Retailer as
soon as possible.
External lights remain ON when the driver’s door
is opened. A chime will sound for 10 seconds as a warning that the lights are on when
the ignition is off and the drivers door is opened. Switch lights off.
Note:
The chime will not sound if the switch is in Autolamp position.
Key in ignition switch. A chime will sound if the key has been left in the ignition and the driver’s
door is opened after the ignition has been switched off or turned to
position ‘I’.
Hazard warning indicators ON. A ticking will sound until the hazard indicators are switched OFF.
Vehicle armed. This warns that the alarm will sound shortly unless the system is disarmed by
either pressing the unlock button on the key transmitter or by placing the key
in the ignition switch.
Left or right direction indicators ON. If the switch has not turned itself OFF, switch the turn indicator OFF when
the manoeuvre is completed. A ticking will sound until the indicators are
switched OFF.
Memory 1, 2 or 3 configuration saved. A short tone as the memory selection is saved.

On the Road 4 - 17
AIR SUSPENSION FAULT None None Drive the vehicle with caution and inform your nearest Jaguar Retailer to have the
fault rectified.
VEHICLE TOO LOW None None The air suspension system is too low. Start the engine and wait for the message to clear before driving the vehicle. If the message is displayed while you are driving,
restrict your speed until the message is cleared. If the message is persistently
shown, inform your Retailer.
DRIVER’S
(or PASSENGER’S) DOOR AJAR None Red The driver’s and/or one or more passenger doors are open. Check that all doors
are closed before driving.
TRUNK OPEN None Red Check that the luggage co mpartment lid is closed before driving.
HOOD OPEN None Red Check that the hood is closed before driving.
ABS FAULT ABS Amber ABS will not be available. The braki ng system will work but care must be used if
braking heavily.
STEERING COLUMN LOCKED None Amber The steering lock system has failed to unlock the steering column. The engine
cannot be started. Remove the key and re-insert it into th e ignition switch, then try
again to unlock the column by turning the steering wheel gently to the left and
right (only small movements will be possible).
TRANSMISSION FAULT None Amber It is likely that the driver will expe
rience a degradation of transmission operation
and possibly reduced ac celeration capability.
Message
Warning
Light Priority
Indicator Meaning

4-24 On the Road
At dawn, as light increases, the sidelights
and headlights switch OFF automatically.
Do not cover the sensor and keep the
windscreen clean. Obstructing the light in
this area of the sensor may lead to
unwanted operation of the sidelights and
headlights.
Note:If the windscreen wipers are
switched on in auto, slow or fast modes
for more than 20 seconds then the
exterior lights will be switched on,
if selected to autolamps mode. The lights
will switch off 2 minutes after the wipers
are switched off or will go off straight
away if autolamps is deselected or the
ignition is turned off.
Exit delay
When parking the car at night, if the
headlights were switched on then they
will remain on for a short period after the
key has been removed from the ignition
switch. This is to give a clearly lit area for
occupants leaving the vehicle.
If the light switch rotary collar is in the
AUTO position there will be no exit delay
and the headlights will turn off when the
light switch is turned off. Three settings on the rotary collar set the
time that the lights will remain on after
the key is removed from the ignition
switch;
•10seconds.
•30seconds.
•2minutes.
Note:
The key must not be in the ignition
switch for this feature to operate.
The message centre shows the delay
setting or when this feature is turned off.
Headlight convenience
When approaching the vehicle,
the sidelights and headlights can be
switched on by pressing the headlight
button on the re mote transmitter.
The lights will come on for 25 seconds or
can be switched off by pressing the
remote transmitte r headlight button
again. Daylight running lights
In certain countries it is a legal
requirement for the lights to be on during
the hours of daylight.
With the rotary co
llar in the OFF
position, dipped headlights, sidelights,
tail lights, number plate lights and side
marker lights will switch on automatically
with the following conditions:
• The ignition is turned to position ‘II’.
• The vehicle gear se lector out of park.
• The parkbrake is not applied (released).

4-26 On the Road
Direction Indicators
The direction indicators, the left column
stalk, operate when the ignition is in
position ‘II’. Move the stalk up for
indicating a right turn or move it down to
indicate a left turn.
Two positions are provided. The first
position, partly moving the stalk up or
down, causes the indicator to flash while
it is held in this position. On releasing the
stalk the indicators stop flashing.
The second position is a full movement of
the stalk up or down, which can then be
released. The indicators will remain
flashing and will cancel when the turn is
completed. An audible ticking an
d a flashing green
arrow on the instrument cluster indicates
that the selected direction indicator is
operating.
Bulb failure
The direction indicators (including those
on a trailer, if attached) and side
repeaters are monitored for bulb failure.
If a bulb fails when it is on, a message is
shown in the message centre. At the same
time, the corresponding side green
warning light will flash at twice the
normal rate. The audible ticking will
sound at twice the normal rate.Door Guard/Puddle Lights
Door guard lights are fitted to each door
to give warning of an open door to
passing vehicles.
Puddle lights illuminate the ‘step out’
area at night.
Each light comes on automatically when
the door is opened. If the door is left
open the lights remain on for 5 minutes
and then switch off.
Approach Lights
Approach lights are fitted in the door
mirrors to provide illumination for the
floor area around the front doors.
The approach lights come on when:
• The vehicle is unlocked using a key, key transmitter or the central locking
switch.
• Using the headlight convenience button on the key transmitter.
• Reverse gear is selected.
The approach lights will not illuminate if
the autolamp sensor determines that the
ambient light is sufficiently bright.
Luggage Compartment
Lighting
The luggage compar tment will be
illuminated when the lid is opened.
Glove Compartment
The glove compartment will be
illuminated when the lid is opened.

4-28 On the Road
Illuminated entry/exit
The interior lights fade on when a door is
opened and go out when the engine is
started or 15 seconds after the last door
is closed. If any door is left open,
the lights will fade off after two minutes.
When the vehicle is unlocked with a key
or the key transmitter, the courtesy lights
will come on at maximum brightness for
two minutes if a door is not opened.
With the engine running, opening any
door will put on all interior lights, they
will go out immediately after the last door
is closed.Battery Saver
If the interior lights are switched on using
the centre switch in the overhead console
and the ignition swit ch is turned to
position ‘0’, the lights will automatically
turn OFF after 40 minutes.
If the interior lights are switched on by
opening a door and the ignition switch is
in position ‘0’, the lights will
automatically turn off after 10 minutes.
If the glove compartmen t or vanity mirror
lights are switched on and the ignition
switch is turned to positions ‘0’ or ‘I’ or
the key is removed, the lights will
automatically turn OFF after 40 minutes.