ground clearance JEEP CJ 1953 User Guide

Dl

DAUNTLESS
V-6
ENGINE
E-105.
DAUNTLESS V-6 ENGINE SPECIFICATIONS

ENGINE:
Type

Number
of Cylinders Valve Arrangement
Bore
Stroke

Piston
Displacement

Firing
Order Compression Ratio

Number
of
Mounting
Points:

Front.

Horsepower
(SAE)

Horsepower
(max. brake) Torque (max.
2400
rpm.)
Cylinder
Numbers,
Front to Rear:
Right Bank

Left
Bank
Cylinder Block Material
Cylinder Head Material English

90°
V-6 6

In
head
3.750"
3.400"

225 cu. in.
1.6.5.4.3.2

*9.0:1

2

33.748

160 @
4200
rpm. 235
lb-ft.

2, 4, 6 1, 3, 5

Cast
Iron
Cast
Iron Metric

9,525
cm.

8,636
cm. 3,69 ltr.

32,49
kg-m.

PISTONS:
Material
Description Clearance Limits:
Top
Land
Skirt
Top

Skirt
Bottom

Ring Groove Depth*. No. 1
No. 2, 3
Cylinder Bore: Out-of-Round (max.). Taper (max.)
Cast
Aluminum Alloy

Cam
Ground, Tin Plated

.0125"
to
.0295" .0005"
to
.0011"

.0005"
to
.0011"

.1880"
to
.1995"
.1905"
to
.1980"

.003"
.005" 0,318 a
0,749
mm.

0,0127
a
0,0279
mm.

0,0127
a
0,0279
mm.

4,775
a
5,067
mm.
4,839
a
5,029
mm.

0,076
mm. 0,127 mm.

PISTON
RINGS:
Function: No. 1 and No. 2 Ring.. No. 3 Ring
Location
Material: No. 1...
No. 2 No. 3.

Oil
Ring Type
Oil
Ring Expander
Width: No. 1
No. 2. .
No. 3

Gap:
No. 1 and No. 2
No. 3

Side
Clearance in Groove: No. 1
No. 2
No. 3 Compression

Oil
Control

Above
Piston
Pin

Iron,
Chrome Plated
Iron,
Pre lubricated
Steel

Dual
Rail,
With Spacer Humped Ring

.0785"
to
.0790" .0770"
to
.0780"
.181" to .187"
.010" to .020"
.015" to .035"
.002" to
.0035"
.003" to .005"

.0015"
to
.0085"
1,993 a
2,007
mm.
1,956 a 1,981 mm. 4,60 a 4,75 mm.
0,25 a 0,51 mm.
0,38 a 0,89 mm.
0,051 a
0,089
mm.
0,076
a 0,127 mm.

0,038
a
0,220
mm.

PISTON
PINS:
Material
Length

Diameter

Type Clearance in
Piston

Clearance in
Connecting
Rod.

Distance
Offset
Toward High-Thrust
Side
of Piston.
Steel,
SAE 1018, SAE 1118

3.060"

.9394"
to
.9397"

Pressed in
Connecting
Rod
.0004"
to
.0007" .0007"
to
.0017"

.040"
7,772
cm.

23,861
a
23,868
mm.

0,0102
a
0,0178
mm.
0,0178
a
0,0431
mm.
1,016 mm.
*State
of California Exhaust Emission Control Engine 7.4 Compression Ratio.
106

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

H
13406

FIG.
H-39—STARTING
CIRCUIT

1—
Ground
Cable
2—
Battery

3—
Positive Cable
4—
Alternator
Wire
5—
Alternator

6— Ignition Switch
Wire

H-93.
Maintenance Procedure

A
periodic inspection should be made of the start­ ing circuit. Since the interval
between
these
checks

will
vary according to the type of service, it should, under normal conditions, be made every 500 hours
of operation. Inspect all starting circuit wiring for damage.
Check
for
loose
or corroded terminals and
for dependable operation of the starting motor.

H-94.
Wiring

Refer
to Fig. H-39. Inspect the starting circuit to make sure that all
connections are clean and tight.
Check
for worn or damaged insulation on the wires. Perform a volt­

age-loss
test
to make sure there is no
loss
of start­ ing motor efficiency resulting from high resistance
connections. Voltage
loss
from the battery ter­
minal
to the starting motor terminal should not
exceed .30 volts for each 100 amperes. Voltage
loss
between
the battery ground
post
and the start­ing motor frame should not exceed .10 volts for
each 100 amperes. If the
voltage
loss
is greater
than
these
limits, measure the
voltage
loss
over
each part of the circuit until the resistance causing the
voltage
loss
is located and corrected.

H-95.
Commutator
Sluggish starting motor operation may be caused by a dirty commutator or worn brushes. The com­mutator cannot be cleaned while the. starting motor is mounted on the
engine
and it
will
be necessary
to remove it and proceed as for an overhaul. Should 7— Ignition Switch
8— Solenoid
Wire

9—
Starter

10— Solenoid
11—
Connector
Strap
the commuator be rough or worn, it should be
removed for cleaning and reconditioning.
H-96.
Overhaul Procedure

At
periodic intervals the starting motor circuit
should be thoroughly checked and the motor re­ moved from the
engine
for cleaning and checking.

H-97.
Removal and Disassembly

Refer
to Fig. H-40 and H-41.
To
remove the starting motor from the engine, dis­
connect the leads and cover the battery lead ter­

minal
with a piece of
hose
or tape to prevent short

circuiting.
Remove the flange
bolts
holding the starting motor to the flywheel housing. Remove
the starting motor from the vehicle.

Each
part of the starting motor should be removed, cleaned, and inspected for evidence of wear or
damage. The Bendix
Folo-Thru
Drive should be
cleaned and inspected for evidence of wear or a distorted spring. Bearings should be checked for
proper clearance and fit. All insulation should be
free of oil and in
good
condition. The armature,
field coils, and brushes should be checked for
good
ground and lack of open circuits.

H-98.
Brushes

a.
The brushes should slide freely in their holders
and
make full contact on the commutator. Worn
brushes should be replaced.
b.
Check
brush spring tension with a spring scale.
Hook the scale under the brush spring near the 203

H

ELECTRICAL
SYSTEM
FIG.
H-49—INSTALLING PINION
STOP RETAINER AND THRUST

COLLAR
ON ARMATURE SHAFT
1—
Retainer

2—
Snap
Ring

3—
Thrust
Collar

4—
Drive
Assembly 5—
Retainer

6—
Groove
in Armature Shaft 7—
Snap
Ring

e. Place thrust collar on armature shaft with shoulder next to snap
ring.
Move the retainer
into contact with
ring.
Using pliers on
opposite

sides of shaft,
squeeze
retainer and thrust collar

together
until snap ring is forced into the retainer.
See Fig. H-49, right hand view.

f.
Lubricate
bearing of drive housing with silicone grease and install armature and drive assembly
in
housing.
g. If field coils were removed from field frame, position coils of replacement field coil assembly
on
pole
shoes
and mount each
pole
shoe
in field
frame
with a
pole
shoe
screw. Use care in tighten­ ing screws to avoid distortion of parts. Be certain
that screws are securely tightened. Insert ends of
field
coil
leads through rubber bushing in field
frame.

h.
Position field frame assembly over armature as­
sembly so that its dowel pin
engages
the
hole
in

drive
housing. Use care to prevent damage to brushes and brush holders. Make sure that brushes

are
properly sealed on commutator.

i.
Install
leather thrust washer on commutator end
of armature assembly.
Lubricate
bearing in com­
mutator end frame with silicone grease and position
end frame to field frame so that armature shaft
enters bearing. Secure field frame and end frame
to drive housing with two
thru
bolts. Connect field leads to motor terminal of solenoid with connect­ing nut.

j.
Whenever the starting motor is disassembled
and
reassembled, the pinion clearance should be
checked.
This
is to make sure that proper clear­
ance exists
between
the pinion and the pinion

stop
retainer when pinion is in cranking position.

Lack
of clearance would prevent solenoid starter

switch
from closing properly; too much clearance
would cause improper pinion
engagement
in ring gear.

k.
Supply 6 volts (3 battery cells or a
6-volt
bat­

tery)
between
S terminal of the solenoid and ground (starter frame).
Caution:
Do not supply more than 6 volts or the
motor
will
operate. As a further precaution to
prevent motor operation, connect a heavy jumper

wire
from the solenoid motor terminal to ground.

I.
After energizing the solenoid, push the drive as­
sembly away from the
stop
retainer as far as pos­
sible and use a feeler
gauge
to check clearance

between
pinion and retainer. See Fig. H-50. If pinion clearance is not .010" to .140" [0,25 a 3,55

mm.],
there is either excessive wear or improper as­
sembly of solenoid linkage or shift lever mechanism.
12771
FIG.
H-50—MEASURING PINION CLEARANCE
1—
Press
Rearward

2—
Pinion

3—
Retainer

4— .010* to .140* Clearance 5—
Feeler
Gauge
210

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

H
Note:
Pinion clearance cannot be adjusted. If
clearance is not correct, motor must be disassem­
bled and checked for the above mentioned defects.

Any
defective parts must be replaced.
H-118. Starting Motor Test —
Genera!

To
obtain
full
performance data on a starting motor, or to determine the cause of abnormal
operation, the motor should be submitted to no-
load and locked armature
tests,
with equipment designed for such
tests.
A high-current variable resistance is required to obtain the specified volt­
age at the starting motor.
This
is necessary since
a
small variation in the
voltage
will
produce a
marked
difference in the current
drawn.

H-119.
Starting Motor No-Load Test

This
test
requires a DC voltmeter capable of
read­

ing
voltages
in a 12-volt
circuit,
a DC ammeter

with
maximum range of several hundred amperes,
a
high-current variable resistance, an rpm. in­

dicator,
and a fully-charged, 12-volt battery.

a.
Connect a jumper lead
between
S terminal
and
large battery terminal of starter solenoid.
Con­
nect voltmeter
between
either of
these
terminals (positive) and motor frame (negative, ground).

Connect
ammeter and variable resistance in series

between
positive terminal of battery and battery

terminal
of solenoid. Set up rpm. indicator to show starting motor speed.
b.
Initially,
adjust variable resistance to a value of
approximately .25 ohm. To complete the
circuit,

connect negative terminal of battery to motor

frame.
Adjust variable resistance to obtain a volt­ meter reading of 10.6 volts;
note
speed of starting motor and ammeter reading. Motor speed should
be
6750
to
10,500
rpm.; ammeter reading should
be 50 to 80 amperes.
c. Rated speed and current indicate normal condi­
tion of the starting motor. Low speed and high
cur­
rent
may show friction; this could be caused by
tight, dirty, or worn bearings, bent armature shaft,

or
a
loose
field
pole
shoe
dragging against the

armature.
It could also be caused by a short-cir­ cuited armature, or by grounded armature or field
coils.

d.
Failure
to operate and high current indicates

a
direct short circuit to ground at either the battery

terminal
or field coils.
e.
Failure
to operate and no current are usually
caused by broken brush springs, worn brushes, high insulation
between
commutator
bars,
or
some
other
condition preventing
good
contact
between
the brushes and commutator. It can also be caused by
open circuit in either the field coils or armature coils.
f. Low speed and low current show high resistance due to poor connections, defective leads, dirty com­
mutator, or one of the conditions mentioned in e,
above.
g. High speed and high current indicates a short
circuit
in the field coils. H-120-
Locked
Armature Test

This
test
requires a DC voltmeter with range ap­

propriate
to read
voltages
in a 12-volt
circuit,
a DC
ammeter with maximum range of several hundred
amperes, a high-current variable resistance, a
clamping fixture to lock
together
the motor shaft

and
case, and a fully-charged 12-volt battery.

a.
Connect a jumper lead
between
S terminal and
large battery terminal of starter solenoid. Connect
voltmeter
between
either of
these
terminals (posi­
tive) and motor frame (negative, ground). Connect
ammeter and variable resistance in series
between
positive terminal of battery and battery terminal
of solenoid.
Install
clamping fixture to lock motor
shaft and case
together
securely.
b.
Initially,
adjust variable resistance to approxi­
mately .05 ohm. To complete the
circuit,
connect
negative terminal of battery to motor frame. Ad­

just
variable resistance to obtain a voltmeter
read­
ing of 4.0 volts. Ammeter reading should be 280
to 320 amperes.

H-121.
Solenoid Starter Switch — Delco

The
solenoid-type switch is mounted directly on
the starting motor.
This
type of switch is energized
by turning the ignition key to the extreme right position. Should the solenoid switch
fail
in service

it
is necessary to install a new assembly.

Should
a starting motor
fail
to deliver maximum power the fault may be due to
voltage
drop at the

starter
switch contacts due to corrosion or burning.

Check
the switch by comparing the
voltage
at the
battery across the terminals. The
voltage
drop
should not exceed .05 volts per 100 amperes.
In
order to remove the starter solenoid, it is neces­

sary
to remove the starter assembly.

H-122.
ELECTRICAL
INSTRUMENTS

H-123.
Fuel
Gauge —
CJ-3B

The
fuel
gauge
circuit is composed of the indicating

unit,
mounted on the instrument panel, and the
fuel tank unit, connected by a single wire through the ignition switch.

Should
the
gauge
fail
to register, check all wire con­ nections to be sure they are tight and clean; also
be sure both units are well grounded. If, after this
check, the
gauge
does
not indicate properly, remove
the wire from the tank unit and connect it to a
new tank unit which must be grounded to the tank

or
frame for
test.
Turn
the ignition switch "ON"
and
move
the float arm through its range of travel,
watching the dash unit to determine if it indicates
correctly.
If it fails to do so the trouble is probably

in
the dash unit and it should be replaced.

Should
a new tank unit be unavailable for this
test,
disconnect tank unit wire at the instrument panel

gauge.
Connect one lead of a 12 V, 1 CP
test
light
to the instrument panel unit terminal and with the
ignition switch
"ON"
ground the other lead. If the
unit is operating correctly the pointer
will
move

approximately three-quarter across the
dial.
Do not attempt to repair either unit; replacement
is the only precedure. 211

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P
lengthening of the brake master cylinder eye bolt.

This
is
done
so the primary cup
will
clear the by­
pass port when the piston is in the off position,
otherwise the compensating action of the master

cylinder
for expansion and contraction of the fluid
in
the system, due to temperature changes,
will

be destroyed and cause the brakes to drag.

Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One
way to
compensate
for this wear is to install a pedal

slack
adjuster kit,
Part
No.
921936.
FIG.
P-6—HAND
BRAKE
ADJUSTMENT

P-10.
Hand Brake

On
Model DJ-5 and DJ-6 vehicles the rear brake

shoes
are operated through cables and conduits to
form the hand or parking brake. A brake cable
equalizer and adjusting rod, Fig. P-6, is located directly back of the frame center cross member.

P-11.
Parking Brake Adjustment

•
Model DJ-5, DJ-6.

The
foot
brakes must be satisfactorily adjusted be­
fore attempting adjustment of the hand brake.

To
adjust the hand brake raise both rear
wheels

free of the floor.
Pull
up three
notches
on the hand

brake
lever and tighten the adjustment until the

rear
brakes drag slightly. Release the hand brake
lever and check the rear
wheels
for drag. The

wheels
must turn freely with the lever released.

P-12.
Transmission Brake Adjustment
The
transmission brake is located on the propeller
shaft at the rear of the transfer case, see Fig. P-4.
The
brake is operated by a cable connection from
the brake handle mounted on the instrument panel.

To
adjust the transmission brake, the following

sequence
should be followed:
Make
sure that the brake handle on the instrument
panel is fully released. Give due attention to the
cable and operating linkage to see that
they
do
not bind. If necessary free up the cable and
lubri­
cate it. Rotate the brake drum until one pair of the
three
sets
of
holes
are over the
shoe
adjusting screw

wheels
in the brake. Use the
edge
of the
holes
in
the brake drum as a fulcrum for suitable adjusting

tool
or a screwdriver, rotate each notched adjusting
screw by moving the handle of the
tool
away from
the center of the drive shaft until the
shoes
are
snug in the drum.
Back
off seven
notches
on the
adjusting screw
wheels
to secure proper running clearance
between
the
shoes
and the drum. Refer
to Fig. P-8.

P-13.
Relining Transmission Brake
Note:
The condition of the brake lining on the
transmission brake can be visually checked through
the adjusting
holes
in the brake drum.
FIG.
P-7—REMOVING
TRANSMISSION

BRAKE
DRUM

1— Tool W-172
2—
Adapter

3—
Brake
Drum
a.
To reline the brake
shoes
and make a major ad­
justment, first remove the four universal joint at­ taching nuts and lower the propeller shaft. Remove
the retracting spring clevis pin and the spring clip.
Remove the hug lock nut, the nut and washer from
the transfer case output shaft. Both the universal
joint companion
flange
and the brake drum may be readily removed by using puller Tool No. W-172

which
is illustrated in Fig. P-7. Remove the two

brake
shoe
retracting springs and the
shoes.

b. Clean all parts with a suitable cleaning solution

and
examine them for damage or wear.

Brake
shoes
may be distorted by improper lining
installation and the lining should be ground true
after installation on the
shoes.
For this reason it
is recommended that new or replacement
shoe
and
lining assemblies be installed.
c. To reassemble, first turn both adjusting screw

wheels
away from the center to "all off" position.
Place a light film of grease on the brake actuating

cam
and install the
shoes.
Install the black
shoe
re­

turn
spring next to the cam and the yellow spring next to the notch adjusting wheel screw. Place the
brake
drum and universal joint
flange
in position

and
install the transfer case output shaft washer,
nut and hug lock nut. 327