fuel filter JEEP DJ 1953 User Guide

Dl
DAUNTLESS
V-6
ENGINE

FIG.
Dl-41—WATER
PUMP
AND
TIMING CHAIN COVER BOLT LOCATION
Cover
Bolts

alternately and evenly 8 to 12 lb-ft. [1,10 a 1,66

kg-m.].

Dl-88.
Install
Crankshaft
Vibration
Damper

a.
Lubricate
the vibration damper hub
before
in­
stallation to prevent
damage
to the crankshaft
front oil seal during installation and when the

engine
is first started.
b.
Install
the vibration damper on the crankshaft.
Secure it with its attaching flat washer and screw.

Torque
the screw to a minimum of 140 lb-ft.
[19,35
kg-m.].

Dl-89.
Install
Crankshaft Pulley
Secure the crankshaft pulley to the crankshaft

vibration
damper with six screws. Torque screws 18 to 25 lb-ft. [2,5 a 3,4 kg-m.].

Dl-90.
Install
Oil
Level
Dipstick

Insert
oil level dipstick
into
the dipstick tube.

Dl-91.
Install
Oil
Pressure Sending Unit

Install
oil pressure sending unit in cylinder block.
Connect electrical wiring harness to unit.

Dl-92.
Install Starting Motor

Secure starting motor and
solenoid
assembly to
the flywheel housing and cylinder block with two attaching screws. Torque screw, which attaches this
assembly to the flywheel housing, 30 to 40 lb-ft. [4,1 a 5,5 kg-m.]. Torque screw, which attaches

bracket
to cylinder block, 10 to 12 lb-ft. [1,4 a 1,7 kg-m.].
Dl-93.
Install
Oil
Filter

Install
a new oil filter
element
at oil filter nipple,
at
left
side
of timing chain cover. Torque 10 to 15 lb-ft. [1,38 a 2,07 kg-m.].

D1-94. Install Water Pump
Be
certain that mating surfaces of the water pump

and
timing chain cover are clean.
Install
a new
gasket
on the pump flange. Secure the pump and
alternator adjustment bracket to the cover with
nine attaching bolts. Torque
bolts
6 to 8 lb-ft. [0,83 a 1,10 kg-m.]. Refer to Fig. Dl-41.

D1-9S.
Install
Cooling Fan
Secure the cooling fan, fan hub, and fan drive
pulley to the water pump shaft
flange
with four
attaching screws. Torque screws 17 to 23 lb-ft. [2,35 a 3,18 kg-m.].

Dl-96.
Install
Alternator
and Fan
Belt

Mount the alternator and bracket assembly on
right
cylinder head with two attaching screws.

Torque
screws 30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

Fasten
the alternator
loosely
to its adjustment
bracket
with attaching flat washer and nut.
Install

the fan
belt
on its pulleys. Pivot the alternator
outward,
away from cylinder block, to apply fan

belt
tension. Adjust fan
belt
tension to 80 lb. [36,2 kg.];
tighten
alternator-to-adjustment bracket
nut to secure adjustment
setting.
Connect wiring
harness to alternator.

Dl-97.
Install
Fuel Pump

Install
two mounting
bolts
and new
gasket
on

flange
of fuel pump. Secure pump to timing chain cover with screws; torque screws 17 to 23 lb-ft. [2,35 a 3,8 kg-m.]. Connect
output
fuel line to
pump.

Dl-98.
Install Exhaust Manifold

Secure each of two exhaust manifolds to corre­
sponding cylinder head with five attaching screws,
and
one nut. Torque screws and nut 15 to 20 lb-ft. [2,07 a 2,8 kg-m.]. See Fig. Dl-42.

Dl-99.
Install Distributor

Insert
distributor drive gear
into
distributor mount-
FIG.
Dl-42—EXHAUST
MANIFOLD INSTALLATION

1—Torque
Bolts—15
to 20
lb-ft.
[2,07 a 2,8
kg-m.]

102

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

E

FUEL
SYSTEM
Contents

SUBJECT
PAR.

GENERAL
E-1 Dash

FUEL
EVAPORATIVE EMISSION
?*^r
CONTROL SYSTEM
..E-2
Canister
.E-3 . Demand Valve E-4

Fuel
Tank.
.E-5
Inspection Test. E-8
Sealed Gas Cap. E-7

Servicing
System E-9
Vapor
Separator or Expansion
Tank
E-6

CARBURETOR
—
HURRICANE F4 ENGINE.
. .
......
..... ,. . .E-10 Accelerating Pump System.............. .E-19 Accelerating Pump Maintenance E-20

Carburetor
Reassembly
E-2
2

Carburetor
Disassembly E-21
Choke
System E-17
Dash
Pot Adjustment E-44

Fast
Idle Adjustment E-18
Float
Adjustment E-12
Float
System. E-ll
High-Speed System . .E-15
Idle
Adjustment .E-14

Low-Speed
System . E-13
Metering Rod Adjustment E-16

CARBURETOR
~r
DAUNTLESS V-6 ENGINE
.E-25
Accelerator Pump Adjustment E-41 Accelerator Pump System. . E-30

Air
Horn Body Assembly E-39
Air
Horn Body Removal and Disassembly.
E-33

Carburetor
Cleaning and Inspection E-36
Carburetor
Removal E-32
Choke
System E-31

Curb-Idle
Speed and Mixture Adjustment. .E-42

E-1. GENERAL
The
fuel system of the Jeep Universal vehicle,
whether equipped with a Hurricane F4 or Daunt­

less
V-6 Engine,
consists
of the fuel tank, fuel lines, fuel pump, carburetor and
air
cleaner.
Fig. E-1, E-2.
Vehicles equipped with a
Fuel
Evaporative
Emis­

sion Control System
also
include a
non-vent

pressure and vacuum
sensitive
gas cap, a liquid
expansion and vapor separator tank, a carbon filled vapor
storage
canister, and a vapor purge line. Service information pertaining to the
Fuel
Evap­

orative Emission Control System is outlined in

Par.
E-2 through
E-9.
Refer to Figs. E-3 and E-4.
The
most
important
attention
necessary to the fuel
system is to
keep
it clean and free from water. It should be periodically inspected for leaks.

CAUTION—Whenever
a vehicle is to be stored for

an
extended
period, the fuel system should be com­

pletely
drained, the
engine
started and allowed to
run
until the carburetor is emptied.
This
will
avoid
oxidization of the fuel, resulting in the formation of
SUBJECT
PAR.
Pot Adjustment .E-44

nal
Carburetor Adjustments.........E-40

Idle
Adjustment
.
E-43 System . . .E-26

Bowl
Body Assembly E-38

Fuel
Bowl Body Disassembly E-34

Idle
System E-27

Main
Metering System E-28
Power System . E-29
Throttle
Body Assembly .E-37

Throttle
Body Removal, and Disassembly. .E-35

FUEL
PUMP
—
HURRICANE F4 ENGINE.
E-45, 54, 60

Cleaning
and Inspection.............
.E-57,
63 Disassembly E-46, 56, 62
Installation E-59, 65
Reassembly
.E-47,
58, 64
Removal
E-55, 61

Testing.
E-49, 50, 51, 52, 53, 66

Vacuum
Pump E-48

FUEL
PUMP
—
DAUNTLESS V-6 ENGINE
E-67
Removal
E-68

AIR CLEANER
—
CARBURETOR
E-69
ACCELERATOR
LINKAGE
.E-70

FUEL
TANK
AND
LINES
E-71
Float
Unit . .E-76
Fuel
Lines E-77
Fuel
Tank
. . .E-72

Fuel
Tank
Cap E-75

Fuel
Tank
Installation. E-74
Fuel
Tank
Removal E-73

SERVICE
DIAGNOSIS
E-78

SPECIFICATIONS.
E-79
gum in the units of the fuel system. Gum formation
is similar to hard varnish and may cause the fuel
pump valves or the carburetor
float
valve to be­
come
stuck or the filter screen blocked. Acetone or commercial fuel system cleaners
will
dissolve

gum formation. In
extreme
cases
it
will
be necessary
to dissassemble and clean the fuel system. In
most

cases, however, a
good
commercial fuel system sol­
vent
used in accordance with the manufacturer's
instructions or one pint [0,6 ltr.] of
acetone
placed
in
the fuel tank with
about
one gallon [4,5 ltr.]
of
gasoline
will
dissolve
any
deposits
as it
passes

through the system with the
gasoline.

E-2.
FUEL
EVAPORATIVE EMISSION CONTROL SYSTEM

Description and Operation

•
Refer to Figs. E-3 and E-4.

The
Fuel
Evaporative Emission Control System
is
designed
to reduce fuel vapor emission that 109

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

E

FIG.
E-3—FUEL EVAPORATIVE EMISSION CONTROL SYSTEM- HURRICANE F4 ENGINE
A—Side
View

1—
Charcoal Canister
2— Purge
Line

3—
Fuel
Tank
4—
Fuel
Filler
Hose 5—
Non-Vented
Gas Cap
B—Plan
View

6—
Vapor
Separator
or Expansion Tank 7—
Fuel
Gauge

8—
Fuel
Line-to-Fuel Pump

9—
p.C.V.
Crankcase
Valve

10—Fuel
Pump

crankcase
vent system. The charcoal canister in­
corporates an integral demand valve
which
regu­

lates
vapors entering the canister as
well
as a
limit
fill
valve
to control air trapping during tank
fill.
The
Fuel
Evaporative Emission Control System
incorporates the following new or modified parts:

E-3.
Canister
The canister used for the vapor control system has
provisions for containing activated charcoal gran­ ules. The material used for the canister body is a

special,
fuel resistant, heat stabilized nylon. At the top of the canister there is the demand valve which
has connections; one vents the vapor to the canister
while the other connection joins the canister to the purge system. These
tubes
enter the canister on

opposite
sides of a baffle which permits uniform
vapor distribution throughout the canister. The
bottom
of the canister is fitted with a filter element
that allows fuel tank venting to atmosphere after vapors are trapped in the activated charcoal.

E-4.
Demand Valve

The
demand valve is integral with the canister. It
is essenitally a combination pressure regulator and

vacuum
relief valve.
This
valve regulates the rate
of vapor
flowing
from the fuel tank into the canister.
The
valve consists of a housing, a spring loaded
diaphragm,
a diaphragm cover, and a vacuum

relief
valve. The operation of the unit is such that
as tank vent pressure increases the diaphragm lifts,
permitting vapor to enter the canister. The pres­
sure
under which this occurs is 4" to 6"
H2O.
This

action regulates the flow of vapors into the canister
under severe soak and operation conditions (temp, changes), but generally prohibits the flow of vapor 111

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

E
there is a relief valve that
opens
to reduce high
(dangerous) pressures in the fuel tank. In con­

junction
with the pressure relief valve there is a
vacuum
relief valve to
stop
collapse of the fuel

tank
in case of a plugged system or failure of the demand valve. When replacing the gas cap, the
same type must be used as originally installed.

E-8.
System Inspection Test

The
fuel emission vent system should be checked

carefully
to ensure the absence of any leaks to the
atmosphere of either liquid or vapor which might
affect the accuracy, safety, or performance of the control system.

To
assure that the sealed system has been properly

installed,
the following
test
procedure has been
developed.
Disconnect the vent line from the fuel tank system
to the activated charcoal canister, induce l/i p.s.i.
air
pressure. If this pressure can be maintained for

a
few seconds the vent system is assured to be sealed. DO NOT add air pressure to the canister
because damage can occur to the demand valve if
care
is not taken.

E-9.
Servicing the System

Periodic
Maintenance — Replace carbon canister filter at
12,000
miles
[19,200
km.] or 12 month in­tervals (more
often
for operation in dusty areas).

This
is the only regular maintenance service

required.

Canister
Filter
Replacement — Disconnect
hoses

from
top of canister, remove canister from mount
-

t
FIG.
E-5—CARBURETOR—
F4 ENGINE,
EARLY
MODEL
1—
Choke
Clamp
Bracket

2—
Choke
Shaft and
Lever
Assembly

3—
Fuel
Inlet
Elbow

4—
Bowl
Vent Tube 5—
Idle
Air Adjusting
Needle
6—
Throttle
Lever
and Shaft Assembly
7—
Idle
Speed Adjusting Screw
8—
Fast
Idle Connector Rod ing bracket. Remove cover from
bottom
of canister
by pulling it down to
disengage
clips. Remove and
discard
polyurethane filter element
(squeeze
ele­

ment out from under retainer bar).
Install
new
filter by squeezing element under retainer bar and positioning it evenly around entire
bottom
of
canister with
edges
tucked under canister lip, snap

bottom
cover in place, reinstall canister on bracket

and
reconnect
hoses.

Vapor
line
hoses
used in this system are made of

special
rubber material.
Bulk
hoses
are available for
parts
service.
Ordinary
rubber
hose
should not be
used to service vapor lines as they are subject to deterioration and may clog the system.
Liquid

vapor separators or expansion tanks and canisters

are
serviced as complete units only.
Canister
air filters, however, are serviced separately.

E-10.
CARBURETOR
—
HURRICANE
F4
ENGINE

A
single-barrel manual choke, down-draft carbure­
tor (Fig. E-6) is used on the
Hurricane
F4 engine.
The
carburetor is internally vented by a tube
opening located in the air horn body of the
car­

buretor.
This
opening is connected by a rubber
tube to the air
outlet
horn of the air cleaner thus
allowing only filtered atmospheric pressure air
to enter the float chamber for balance pressure
of the carburetor fuel.

Note:
A carburetor with a specific flow character­

istic
is used for exhaust emission control. The
carburetor
is identified by a number, and the correct

carburetor
must be used, when replacement is
necessary.

Early
production models
CJ-3B,
CJ-5,
CJ-5A,
CJ-6,
and
CJ-6A
have a
Carter
YF-938SD
carbure­
tor superseding the earlier
YF-938SC,
YF-938SA,

or
YF-938S
models.

Note."
Conversion kits for changing earlier models
to SD models are available. See Par E-23. It is recommended that when a carburetor is converted
that a tag be fashioned stamped with the new model number and installed under one of the air

horn
screws.
Look
for such a tag to determine if
the carburetor has previously been converted.

Carburetors
listed above are all in the same YF
series and have only minor differences. Descriptions
and
repair procedures given in the following
para­
graphs apply equally to all
YF-series
carburetors.
YF-series
carburetors employ manual and vacuum
control of the metering rod and accelerator pump.
The
carburetor controls and vaporizes the fuel
through five separate systems: float system, low-
speed system, high-speed system, choke system,

and
accelerating-pump system. A description of the function and operation of each system provides an over all description of the carburetor.

For
identification, the series designation is stamped
on the body under the name
Carter
and the model
designation is stamped on a flange protruding
from
the body.

Note:
When checking for carburetor icing causes,
also check the vacuum-pump-to-manifold vacuum
line connector. 113

'Jeep9
UNIVERSAL
SERIES
SERVICE
MANUAL

E
exterior moving parts of a carburetor are
often

responsible for unsatisfactory performance.
For
this

reason,
efficient carburetion depends upon careful cleaning and inspection while servicing.

a.
Thoroughly clean carburetor castings and metal
parts
in carburetor cleaning solvent.

Caution:
Accelerator pump plunger and any fiber

or
rubber parts should never be immersed in
car­

buretor
cleaner. Wash pump plunger in cleaning
solvent.

b.
Blow out all passages in the castings with com­
pressed air. Dry all parts with compressed air.

Make
sure all jets and passages are clean. Do
not use wire to clean fuel passages or air bleeds.

c.
Check
inlet valve
needle
and seat for wear. If

wear
is noted, the assembly must be replaced.

d.
Check
float hinge pin for wear and check float
for damage.

e.
Check
throttle and choke shaft bores for wear

and
out-of-round.
f. Inspect idle mixture adjustment
needles
for
burrs
or
grooves; replace if damaged.
g. Inspect cup of accelerator pump plunger; re­
place if damaged, worn, or hardened. Inspect pump

well
in bowl for wear or scoring.

h.
Check
filter screens for
dirt
or lint.
Clean,
and

if
they remain
clogged,
replace.

i.
If for any reason parts have
become
loose
or
damaged in the cluster assembly, the assembly
must be replaced.

Note:
Use ijew gaskets whenever the carburetor
is disassembled.

E-37.
Throttle Body Assembly
a.
Install
idle mixture adjustment
needles
and
springs in throttle body. Tighten finger-tight, then
unthread
one
turn
as a preliminary adjustment
setting.

Caution:
Do not force idle mixture adjustment
needles
against
seats
or damage may result.

b.
Invert
fuel bowl body and place new throttle
body gasket on bowl. Fasten throttle body to bowl
body with three screws and lockwashers; tighten

securely.

E-38.
Fuel
Bowl Body Assembly

a.
Drop steel discharge check
tall
of accelerator
pump into discharge hole.
Install
pump discharge

spring
and T-shaped retainer. Stake retainer in
place.

Note:
Top of retainer must be flush with flat

surface
of fuel bowl body.

b.
Install
two inserts in main well. Align surface
on lip of insert with flat surface in recess on top
of main well.
Install
venturi cluster with gasket,

and
tighten mounting screws evenly and securely.

Be
certain that center screw is fitted with fiber gasket, and that a special smooth shank screw is
used.
c.
Install
two main metering jets, power valve
gasket and power valve.

d.
Install
small aluminum inlet check
ball
in ac­

celerator
pump inlet at
bottom
of pump well. In­

sert
pump return spring into well, and center by
pressing spring downward with finger.

e.
Install
pump inlet screen in
bottom
of fuel

bowl.

E-39.
Air
Horn Body
Assembly

a.
Install
choke lever and collar on choke shaft.

Prong
on choke lever must face away from air

horn
body and be on top of choke trip lever.
b.
Install
choke shaft and lever assembly into the

air
horn. Choke rod
hole
in the choke lever must
face fuel inlet side of carburetor.

c.
Install
choke valve plate in choke shaft so that
letters RP
will
face upward in finished carburetor.
Install
two new valve plate attaching screws, but
do not tighten securely until valve plate is centered.

To
center choke valve plate on choke shaft, hold
choke valve tightly closed, then slide choke shaft

inward
to obtain approximately .020" [0,508 mm.]

clearance
between
choke trip lever and choke lever

and
collar assembly. Tighten choke valve screws

securely,
and stake lightly in place. Choke valve

will
be perfectly free in all positions when installed
correctly.

d.
Insert
outer accelerator pump lever and shaft as­ sembly into air horn body, with lever pointing to­

ward
choke shaft.
Install
inner pump arm, with plunger
hole
inward,
and tighten set screw securely.
Position pump plunger assembly on inner pump
arm,
with pump shaft pointing
inward,
and install

retainer.

e.
Install
needle
seat screen on inlet valve seat. In­

stall
seat and gasket in air horn body. Tighten seat
securely with a wide-blade screwdriver.
f.
Install
power piston into vacuum cavity.
Lightly
stake piston retainer washer in place. Piston should

travel
freely in cavity.
g.
Install
air horn gasket on air horn body, fitting
gasket over guide pin.

h.
Attach inlet valve
needle
to float.
Carefully

position float and insert float hinge pin. Drop tang
at
rear
of float arm downward toward air horn.

i.
Install
fuel inlet fitting, if removed.

j.
With
air horn assembly inverted, measure the distance from the air horn gasket to top of float
at toe \%£f [27,78 mm.] for standard carburetors

and
\%i [29,36 mm.] for exhaust emission control
equipped carburetors, as shown in Fig. E-23. Use
float level
gauge
J-5127-2. Bend float arm as re­

quired
to adjust float level.

k.
With
air horn body held upright, measure dis­
tance from gasket to
bottom
of float
pontoon
at outer end. Use a l7/s" [47,625 mm.] float drop

gauge.
Bend float tang, as required, to adjust float

drop.
See Fig. E-24.

I.
Carefully
place air horn body on fuel bowl
body, making certain that the accelerator pump
plunger is properly positioned in the pump well.
Lower
the cover gently, straight down; install air 123

FUEL
SYSTEM
|
11893

FIG.
E-29—FUEL
AND
VACUUM
PUMP—F4
ENGINE,
EARLY
MODELS

1—
Cover
Screw
2—
Lockwasher

3—
Diaphragm
Spring
4—
Spring
Seat 5—
Diaphragm
and Rod
6—
Oil
Seal 7—
Valve
Assembly
8— Body
9—
Rocker
Arm Pin Spring
10—
Fuel
Diaphragm
11—
Oil
Seal Retainer
12—
Diaphragm
and Rod 13—
Valve
Retainer
14—
Cover
15—
Gasket

16—
Screen

17—
Bow!

18—
Bail
19—
Gasket

20—
Screw
21—
Rocker
Arm Spring
22—
Link
Spacer
23—
Rocker
Arm

24—
Washer

25—
Body
fuel. The diaphragm can start and
stop
many
times
in
each mile of vehicle operation, but the pump
actuating lihkage is always in operation while the

engine
is running. The fuel pump incorporates a
pulsator and pulsator chamber to dampen the
effect

of pump pressure pulsations on the carburetor

needle
valve.
This
prevents high fuel level in the

reservoir
that would result from the
needle
being

jarred
away from its seat. Also, operating
economy
would be affected because a high fuel level usually results in an over-rich mixture.

The
actuating linkage has its own spring to ensure
continuous contact of the lever to the camshaft
eccentric.

This
fuel pump has a sediment bowl and filtering
screen which is attached to the top of the pump by
a
wire clamp and thumb nut. The screen and sedi­
ment bowl should be cleaned at least twice yearly
to prevent trouble due to a blocked screen or water
freezing. The bowl should be washed and wiped

dry
and the screen dried and then cleaned with a
stiff
brush.
When reassembling the bowl make cer­
tain
that the cork gasket is not broken; reverse it
and
position it flat on the seat, then install the
bowl and tighten the thumb nut securely. After
cleaning, start the
engine
and carefully inspect the
bowl for leakage.

E-46.
Disassembly
Remove the cover plate, gasket, and screen or
bowl clamp, sediment bowl, gasket and screen if so equipped.
Mark
the two castings with a file to
ensure positioning in the same relation upon
assembly. Remove the screws attaching the fuel cover to the pump body. Remove the cover,

diaphragm,
and spring. Remove rocker arm pin,
rocker
arm, and rocker arm spring. Remove the
valve plate screw and separate the valve plate

retainer,
valve gaskets, and valves.

Clean
all parts in cleaning solvent and blow out

with
compressed air. Valves should not be removed

from
the valve housing assembly.
Check
all parts
to see that
they
have not
been
cracked or broken
and
that screw threads have not
been
stripped or
cross threaded. Refer to Par. E-49 for fuel pump
testing. 126

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

E
E-47.
Reassembly

•
Refer to Fig. E-29.
Install
the valve gaskets, valves, valve retainer and
secure them with the valve retainer screws. Make
sure that the inlet and
outlet
valves are in their proper positions. Place the diaphragm spring re­
tainer in position on the diaphragm
pull
rod
and
install diaphragm spring. Position the
dia­

phragm assembly in pump
body
and attach the
cover to pump body, with file marks aligned, with
the six attaching screws. Do not draw the screws
up tight.
Install
rocker arm spring, rocker arm

pin
washers, rocker arm and rocker arm pin.
With

rocker
arm positioned on the diaphragm rod, draw
the six pump
body
screws up evenly and securely.
Install
the filter screen, cork gasket and sediment
bowl and secure them firmly with the thumb screw
on the bowl clamp.

E-48.
Vacuum
Pump

The
double-action fuel pump resembles two single-
action pumps placed one
above
the other. A single
fuel pump rocker arm actuates the two separate diaphragms. One diaphragm is part of the fuel
delivery pump and operates as described in Par.
E-45.
The other diaphragm is part of the vacuum
pump and operates as described here.

As
the actuating lever forces the diaphragm upward against spring pressure, air is forced through the

outlet
port
into
the
engine's
intake manifold. On
the return stroke, spring pressure forces the
dia­
phragm downward, creating a
partial
vacuum and
opening the inlet valve. In this manner, air is pumped out of the windshield wiper motor and
into

the intake manifold. When the wiper motor is shut off, manifold vacuum holds the diaphragm against its spring so that the
full
motion of the actuating
lever is not accompanied by a
complete
up-and-
down motion of the diaphragm.

When
the windshield wiper motor is turned on, but manifold vacuum is greater than the vacuum
created by the
booster
pump, air
flows
from the
wiper motor through both valves of the vacuum
booster.
As manifold vacuum drops off as a result
of the
engine
operating under low
speed
and high load, the vacuum created by the vacuum
booster

will
be greater than
engine
intake manifold vacuum

and
the pump
will
operate the wiper motor when the wiper control switch is turned on.

•
Refer to Fig. E-29. Remove the
eight
cover attaching screws and
lockwashers, and remove the cover, diaphragm

spring
and spring seat. Detach the diaphragm rod
from the rocker arm and remove the diaphragm.
The
valve assemblies are pressed
into
the cover

and
body
and lightly staked. They may be removed
with the point of a knife blade. If installing new valves be sure the inlet and
outlet
valves are
correctly positioned and stake them lightly with

a
small punch.
Assemble the vacuum pump in the reverse order
of disassembly, drawing the cover attaching screws up evenly and tightly.
E-49.
Fuel
Pump
Testing

Four
tests
are presented in following paragraphs to
test
for proper operation of the fuel pump. In addi­
tion, check the following:

a.
Check
for secure mounting of the fuel pump.

The
rocker arm may be working the entire pump
up and down, rather than just the pump
dia­

phragms.
b. Remove and clean the fuel sediment bowl.
c.
Check
all fuel lines.
E-50.
Volume
Check

To
measure fuel pump capacity (amount of fuel
delivered in a given time) disconnect the pump-to-

carburetor
line at the carburetor end. Place the

open
end of the line in a suitable container.
Start

the
engine
and operate at normal idle speed.
Delivery
should be one quart U.S. [1 ltr.] within
one minute.

E-51.
Pressure
Check

To
measure fuel pump pressure (force of fuel de­

livery)
disconnect the pump-to-carburetor line
at the carburetor end. Plug a pressure
gauge
and T-fitting
into
the
open
end of this line and
into
the

carburetor.
Start
the
engine
and operate at normal
idle speed. Pressure should be 2J4 to 3% psi.
[0,716
a
0,264
kg-cm2] at 1800 rpm. and at 16"
[406 mm.]
above
the
outlet.

E-52.
Vacuum
Check

To
measure fuel pump vacuum (pull of. the pump
at the inlet side) disconnect the pump-to-fuel-tank
line at the fuel pump. Attach a vacuum
gauge
to the fuel pump inlet.
Start
the
engine,
accelerate to
specified speed, and hold this
engine
speed
while
taking a
gauge
reading. Permissible
gauge
reading
is 8* [203 mm.] of mercury [Hg] at 1200 rpm. and
10j^'
[267 mm.] at 1800 rpm.
E-53.
Vacuum
Booster
Check

To
test
the condition of the vacuum
booster
pump,
disconnect both inlet and
outlet
lines at the pump.

Attach
a vacuum
gauge
to the windshield wiper
connection at the pump.
Start
the
engine,
accelerate
to
2000
rpm., and hold this
engine
speed
while taking a
gauge
reading. Permissible
gauge
reading
is 10* to 14" [254 a 356 cm.] of mercury [Hg].
E-54.'
FUEL
PUMP
(SINGLE-ACTION)
—
HURRICANE
F4
ENGINE
•
Early
Models.
Vehicles with electric windshield wiper motors are
equipped with a single-action fuel pump (Fig.

E-30).
The fuel pump cam lever is activated by an eccentric on the
engine
camshaft. When the
car­

buretor float
needle
valve closes, accumulation of
fuel in the pump
extends
the diaphragm spring.

This
action causes the rocker arm linkage to be­
come
inoperative until the pressure on the
dia­
phragm and spring is reduced. The fuel pump dis­
charge pressure is thus controlled by the diaphragm

spring.
This
provides a steady supply of fuel to the
carburetor
at a fairly constant pressure. 127

'Jeep9
UNIVERSAL
SERIES
SERVICE
MANUAL

E-59.
Fuel
Pump Installation

a.
Make certain mating surfaces of fuel pump and
engine
cylinder case are clean. Cement a new gasket
to mounting
flange
of fuel pump.
b. Position fuel pump on cylinder block, so that

cam
lever of pump rests on fuel pump cam of cam­
shaft. Secure pump to block with two cap screws

and
lock washers.
c. Connect intake and
outlet
fuel lines to fuel
pump.

E-60.
FUEL
PUMP
(SINGLE-ACTION)
—
HURRICANE
F4
ENGINE
•
Late
Models.

The
Hurricane F4
engine
is equipped with a single-
action fuel pump (Fig.
E-31).
The fuel pump cam lever is activated by an eccentric on the
engine

camshaft. When the carburetor float
needle
valve
closes, accumulation of fuel in the pump
extends

the diaphragm spring.
This
action causes the rocker

arm
linkage to
become
inoperative until the pres­
sure on the diaphragm and spring is reduced. The fuel pump discharge pressure is thus controlled by
the diaphragm spring.
This
provides a steady sup­ ply of fuel to the carburetor at a fairly constant
pressure.

E-61.
Fuel
Pump Removal

To
remove the fuel pump from the
engine,
dis­
connect the inlet and
outlet
fuel lines. Remove
the two fuel pump
body
attaching nuts, lock washers, and washers, and pull the fuel pump and
gasket free of the
engine.

E-62.
Fuel
Pump Disassembly

Note:
The fuel pump is serviced with a repair kit.

Individual
service parts are also available. The
valves are not replaceable but are serviced as part
of the valve housing.

•
Refer to Fig. E-32.

a.
Remove filter bail assembly, bowl,
element,

spring,
and gasket from filter cover. b.
File
a locating
mark
on the
edges
of the valve
housing and the pump body. Remove the six at-

14280
FIG.
E-32—FUEL
PUMp—

HURRICANE F4 ENGINE,
LATE
MODELS

12988

FIG.
E-31—FUEL
.PUMP-

HURRICANE F4 ENGINE,
LATE
MODELS 1—
Bail

2—
Bowl

3—
Spring

4—
Filter
5—
Gasket

6— Pump Body 7—
Gasket

8—
Valve
Assembly 9— Screws 10—
Valve
Housing
11—
Valve
Assembly
12— Screws
13—
Diaphragm
and Oil Seal 14— Pump Body
15—
Cam
Lever
Spring 16—
Cam
Lever

17—
Gasket

18—
Cam
Lever
Pin and Plug 129

E

FUEL
SYSTEM
taching screws and valve housing from the fuel
pump body.

c.
Remove the two screws in the valve housing
and
separate the filter cover and air
dome
dia­
phragm.

d.
Remove the cam lever return spring, plug,
cam
lever pin, and cam lever from the pump body.

Tap
the cam lever pin out of body, using a drift
inserted through the small
hole
in the pump body.
e. Remove diaphragm from pump body.
f. Under normal service, the pump may be cleaned without further disassembly.

Note:
The oil seal (at top of spring in diaphragm
assembly) seals the spring side of the fuel
dia­
phragm
from the crankcase. Any deposit, in
excess

of a few drops, of oil on the diaphragm indicates leakage past the oil seal. Be sure the seat for the

seal
in the pump body is clean and smooth.

E-63.
Fuel
Pump Cleaning and Inspection

Caution:
Do not immerse valves or diaphragm
in
cleaning solvent; wipe clean.

Clean
all metal parts of the fuel pump in solvent.
Brush
with a stiff-bristled
brush.
Dry with com­
pressed
air.
Check
all parts to see that they are not
cracked
or broken and that the screw threads are
not damaged.

E-64.
Fuel
Pump Reassembly
•
Refer to Fig. E-32.

a.
Assemble the valve housing and filter cover, using a new air
dome
diaphragm. The opening

in
the air
dome
diaphragm is located over the
intake
valve. The filter cover is positioned cor­
rectly
when the inlet passage in the cover aligns

with
the inlet valve. Tighten the attaching screws
alternately and securely.

b.
Lubricate
diaphragm assembly shaft, around

oil
seal, with
engine
oil. Position diaphragm as­ sembly on valve housing and thread all the attach­ ing screws through diaphragm.
(This
helps avoid
damage to the screw
holes
in diaphragm.)

c.
Place diaphragm assembly and valve housing
in
position on pump body (align marks made
before disassembly).
First
start all screws one

or
two threads; then tighten the screws alternately

and
securely.

d.
Lubricate
forked end of cam lever, pin bore
of body, and corresponding
hole
in lever, and the
pin
itself with
engine
oil.

Note:
Forked
end of lever
goes
around diaphragm
shaft. Be sure
loose
bumper washer on diaphragm shaft is on top of lever and
between
lever and fixed
washer
on shaft.
e.
Install
lever and pin. To install pin, use a drift
and
tap pin into the
hole
in the body until it hits
the
stop
on the
bottom
of the hole;
move
the lever while tapping, to align
hole
in lever with the pin;
then install plug.
Install
lever return spring.
f.
Install
a new filter bowl gasket in filter cover.
Place
bail
assembly in ears on cover and swing
to one side.
Install
spring and new filter element in
bowl and install bowl on pump. Position
bail
as­
sembly under bowl; tighten retainer screw.

Caution:
Do not overtighten screw.

E-65.
Fuel
Pump Installation

a.
Make certain mating surfaces of fuel pump and

engine
cylinder case are clean. Cement a new gasket to mounting flange of fuel pump.

b.
Position fuel pump on cylinder block, so that

cam
lever of pump rests on fuel pump cam of cam­
shaft. Secure pump to block with two cap screws
and
lock washers. Torque
bolts
13 to 17 lb-ft. [1,8
a
2,3 kg-m.].

c.
Connect intake and
outlet
fuel lines to fuel
pump.

E-66.
Fuel
Pump Testing

Whenever
the fuel pump is to be checked for pres­

sure
or volume, follow the procedure outline in

Par.
C-23 of this manual.
Fuel
pump pressure is
important
for low pressure
will
seriously affect en­

gine
operation and high pressure can cause exces­
sive fuel consumption and flooding of the carbure­
tor.
Should there be any doubt of normal opera­
tion, check the procedure as outlined in Par. C-23.
In
addition to proper fuel pressure, volume of the
pump is also important. When testing for proper
pump pressure, be certain to also
test
for volume
as the pump may build up sufficient pressure, but
fail
to produce sufficient volume.

E-67. FUEL
PUMP
—
DAUNTLESS
V-6
ENGINE

Jeep vehicles equipped with the Dauntless V6-225

engine
have a special fuel pump which has a metering
outlet
for a vapor return system. Any

vapor
which forms is returned to the fuel tank
along with hot fuel through a separate line along­
side the fuel supply line.
This
greatly reduces any
FIG.
E-33—FUEL PUMP—DAUNTLESS V-6 ENGINE
1
—Fuel
Outlet 2—Vapor
Return
3—Fuel
Inlet

130

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

E
possibility of vapor lock by keeping cool fuel from
the tank constantly circulating through the fuel
pump.

Fuel
pump pressure at carburetor (inlet) on Daunt­
less
V6-225
engine
should be 3% lbs.
[0,264
kgm-cm2] minimum at idle with the vapor return
hose

squeezed off. With the vapor return
hose
open
pump pressure should be 2j^ lbs. [0,176 kg-cm2]
minimum.

The
Dauntless V-6
engine
is equipped with a sealed

unit,
non-repairable, single-action fuel pump (Fig.

E-33).

Note:
All Dauntless V-6
engines
are equipped with

a
throw-away can-type gasoline filter installed in
the fuel line
between
the fuel pump and the
car­
buretor.
This
unit must be replaced every
12,000
miles
[19.200
km.] of vehicle operation.

E-68.
Fuel
Pump Removal

To
remove the fuel pump from the Dauntless V-6
engine, disconnect the fuel inlet, fuel
outlet
and fuel return lines from the pump. Remove the two
fuel pump body attaching cap screws and lock

washers.
Pull
the fuel filter bracket free and remove the pump and gasket. Discard pump and gasket.
Install
new pump in reverse procedure of removal.

E-69.
AIR
CLEANER

Servicing
of the air cleaner is properly taken care of as part of the periodic lubrication and servicing of the vehicle. For this reason, air cleaner servicing
information is given in the Lubrication Section.

Refer
to and follow the instructions given there.

E-70. ACCELERATOR LINKAGE
The
accelerator linkage is properly adjusted when
the vehicle leaves the factory. However, in time
components parts
will
become
worn and require re­
adjustment to maintain a smooth even control of
engine
speed. On Models equipped with F4
engines

the adjustment is made at the adjusting block,

Fig.
E-34. Loosen the lock nuts, and adjust the length of the accelerator rod so that when the
car­

buretor throttle valve is wide open the accelerator
treadle
will
just strike the toe board. After correct
adjustment is made tighten both lock nuts firmly.
To
adjust the accelerator linkage on V6
engines

loosen
the lock nuts securing the accelerator rod
housing to its securing bracket and adjust the length
of the accelerator rod so that when the carburetor throttle valve is wide open the accelerator treadle

will
just strike the toe board. After correct adjust­
ment is made, tighten lock nut firmly, see Fig. E-35 for Dauntless V-6 engine.

E-71. FUEL
TANK
AND
FUEL LINES
The
following paragraphs (E-70 through E-73) describe the removal, installation and services to
be performed when replacing the fuel tank or
servicing
the fuel system.

FIG.
E-34—ACCELERATOR LINKAGE,
F4
ENGINE
1—
Grommet

2— Nut and Lockwasher

3—
Throttle
Control
4—
Choke
Control 5—
Treadle
Rod Seal
6—
Accelerator
Treadle
7—
Treadle
Hinge Pin
8—
Treadle
Hinge 9— Nut and Lockwasher
10—
Screw

11—
Accelerator
Rod
12— Nut
13—
Adjusting
Block
14—
Retracting
Spring
15—
Cotter
Pin
16—
Lower
Beilcrank
17—
Washer

18—
Beilcrank
Link
Rod
19—
Bracket

20—
Throttle
Wire
Stop
21—
Beilcrank
Spring
22—
Rod

23—
Upper
Beilcrank
24—
Wesher
10731
131