radiator JEEP DJ 1953 User Guide

Fl

EXHAUST
EMISSION
CONTROL
SYSTEMS
IMPORTANT
NOTICE

The
Exhaust
Emission Systems covered
in
this publication
meet
State and

Federal
requirements for hydrocarbon and carbon
monoxide
emissions.

To
assure continued proper operation,
these
systems
must
be
inspected

regularly,
parts must be replaced
at
factory-recommended intervals and
engine

tune-up services performed at intervals specified in the
Exhaust
Emission
Con­
trol
System Maintenance charts.

For
the
above
reasons,
these
systems
must not, under any circumstances,
be

altered
to anything other than
required
specifications provided in this publication.

Further,
the
Exhaust
Emission
Control
System, or any
of
its components, must
not be physically altered or modified in any respect.

DHTfl
TAG

For
the serviceman's guidance, each vehicle equipped with exhaust emission

control
will
have data
tag
permanently affixed
to the
radiator shroud—-in
example:

VEHICLE
EMISSION
CONTROL
INFORMATION
MODEL
F4-134
C.I.D.

•
ENGINE
AT
NORMAL
OPERATING
TEMPERATURE

•
LIGHTS
AND
ALL
ACCESSORIES OFF

•
IDLE
MIXTURE
. . .
LEAN
BEST
IDLE

•
IGNITION
TIMING
0*
(TDC)
•
SPARK
PLUG
GAP
. . . .030

•
DWELL
...
42* (.020
POINT
GAP)
•
IDLE
SPEED
. . .
700-750 RPM
TRANSMISSION
IN
NEUTRAL
DURING
TUNE
UP

SEE SERVICE MANUAL
FOR
ADDITIONAL INFORMATION
THIS VEHICLE CONFORMS
TO U.S.
DEPT.
OF
H.E.W.
REGULATIONS APPLICABLE
TO
1971 MODEL YEAR NEW MOTOR VEHICLES

Jeep
CORPORATION
14401

Important:
Always refer
to
the data tag when checking or re-adjusting ignition

timing,
idle speed, and idle mixture. 148

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

F2
F2-35.
EXHAUST EMISSION CONTOL SYSTEM
DISTRIBUTOR SPECIFICATIONS

Distributor:
Make
Delco-Remy Prestolite Prestolite
Model...
1110376
IAT-4501 or IAT-4502 IAT-4502A

Breaker
Point Gap .016"
[0,406
mm.] .016"
[0,406
mm.] .016"
[0,406
mm.]

Breaker
Arm Tension 19 to 23 oz. [538 a 652 gr.] 17 to 22 oz. [482 a 623 gr.] 17 to 22 oz. [482 a 623 gr.]

Cam
Angle. 29° to 31° 29° + 3° 29° ± 3°

Max.
Auto Advance
(Crankshaft
Degrees). 13° to 15° at 1,950 rpm. 16° (& 1800 rpm. 21° @ 1800 rpm.
26°
@
4200
rpm. (Max.) 32° @
4200
rpm. (Max.)

Max.
Vac. Advance
(Distributor
Degrees) 8° 8° 8°
Condenser Capacity. .18 to .23 mfd. .25 to .28 mfd. .25 to .28 mfd.

Timing:
Crankshaft
5°
(BTC)
@ Idle 5°
(BTC)
© Idle 0°
(TDC)
© Idle

Mark
Location Crankshaft Pulley Crankshaft Pulley Crankshaft Pulley

Firing
Order
1-6-5-4-3-2 1-6-5-4-3-2 1-6-5-4-3-2

F2-36.
SPARK PLUG
GAP

Spark
Plug Gap. .035"
[0,889
mm.]

IMPORTANT
NOTICE
The
Exhaust Emission Systems covered in this publication
meet
State and Federal
requirements for hydrocarbon and carbon
monoxide
emissions.

To
assure continued proper operation,
these
systems
must be inspected regularly,
parts must be replaced at factory-recommended intervals and
engine
tune-up services
performed at intervals specified in the Exhaust Emission Control System Maintenance
charts.

For
the
above
reasons,
these
systems
must not, under any circumstances, be altered
to anything other than required specifications provided in this publication.
Further,

the Exhaust Emission Control System, or any of its components, must not be physi­
cally
altered or modified in any respect.

DATA
TAG

For
the serviceman's guidance, each vehicle equipped with exhaust emission control

will
have data tag permanently affixed to the radiator shroud — in example:

VEHICLE EMISSION CONTROL INFORMATION MODEL V6-225 C.I.D.

•
ENGINE
AT
NORMAL OPERATING TEMPERATURE

•
LIGHTS
AND ALL
ACCESSORIES
OFF

•
IDLE MIXTURE
.. .
LEAN BEST IDLE

•
IGNITION TIMING
0*
(TDC)
*
SPARK PLUG
GAP 035
•
DWELL
. . . 30* (.016
POINT
GAP) •
IDLE SPEED
. . .
650- 700
RPM
TRANSMISSION
IN
NEUTRAL DURING TUNE
UP

SEE
SERVICE MANUAL FOR ADDITIONAL INFORMATION

THIS VEHICLE CONFORMS
TO U.S. DEPT. OF H.E.W.
REGULATIONS APPLICABLE
TO
1971
MODEL YEAR
NEW
MOTOR VEHICLES
Jeep
CORPORATION
14400
NOTE:
The
above
tag applies to vehicles equipped with Distributor Model
IAT-4502A.

On
vehicles equipped with Distributor Models
1110376,
IAT-4501 and IAT-4502 the tag is the same

except
that Ignition Timing is 5°
T.D.C.

Always
refer to the data tag when checking or re-adjusting ignition timing, idle speed, and idle mixture.
159

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

COOLING
SYSTEM

Contents

SUBJECT
PAR.

GENERAL
.G-l Antifreeze Solutions. .G-l6
Cylinder
Block.
..................
.G-8

Draining
Cooling System............... G-3

Engine
Overheating..
.................
.G-19
Fan
Belt.
......... .........
.G-18
Filling
Cooling System.................
G-2

Inhibited
Coolant Solution .G-l7

Temperature
Sending Unit.
...........
.G-l0

Thermostat
.........................
G-9

RADIATOR
.G-5
Radiator
and Heater Hoses.............
G-7
SUBJECT
PAR.

Radiator
Pressure
Cap.................
G-4

Radiator
Removal and Replacement..... G-6

WATER
PUMP.
. . .G-ll
Water
Pump Disassembly. .............G-13

Water
Pump Inspection.
..............
.G-12

Water
Pump Reassembly.
.............
.G-14

Water
Pump Removal and Replacement. .G-l5

SERVICE
DIAGNOSIS.
.G-20

SPECIFICATIONS
. .G-21

ANTIFREEZE
CHART.
..... ... .G-22

G-l. GENERAL
a.
The satisfactory performance of the Hurricane

F4
engine
is controlled to a great
extent
by the proper operation of the cooling system. The
engine

block is full length water jacketed which prevents
distortion of the cylinder walls. Directed cooling
and
large water holes, properly placed in the cylin­
der head gasket cause more water to flow past the
valve
seats
(which are the
hottest
parts of the

block)
and
carry
the heat away from the valves, giving positive cooling of valves and seats.

Minimum
temperature of the coolant is controlled by a thermostat mounted in the
outlet
passage of
the engine. When the coolant temperature is below
thermostat-rated temperature, the thermostat re­ mains closed and the coolant is directed through
the radiator-bypass
hose
to the water pump. When the thermostat opens, coolant flow is directed to
the top of the radiator. The radiator dissipates the
excess
engine
heat before the coolant is recirculated
through the engine.
The
cooling system is pressurized. Operating pres­
sure
is regulated by the rating of the radiator cap

which
contains a relief valve, b. The Dauntless V-6
engine
efficiency and per­formance is controlled to a great
extent
by proper
operation of the cooling system. The cooling system

does
more than cool the engine. It also directs
the flow of coolant to provide the
best
operating
temperature range for each part of the engine.

In
the Dauntless V-6
engine
coolant is forced by
the water pump into two main passages that run the length of the block on each side (Fig. G-l).
FIG.
G-1—COOLANT
FLOW
THROUGH
THE
DAUNTLESS
V-6
ENGINE

161

COOLING
SYSTEM

14263

FIG.
G-2—COOLING SYSTEM
COMPONENTS
V-6
ENGINE

1—
Radiator
Pressure Cap

2—
Hose
Clamp

3—
Radiator
Hose (Inlet-Upper)
4—
Radiator
Hose (Outlet-Lower) 5—
Bolt
6—
Water
Pump Assembly 7—
Cap
8—Thermostat
By-Pass Hose
g—Water Outlet
Elbow

10—
Gasket

11—
Thermostat
12—
Water
Pump Gasket

13—
Dowel
Pin
14—
Radiator
Shroud (Heavy Duty Cooling) 15—
Pulley

16—
Fan
Spacer
17—
Fan
and Alternator Belt

18—Fan

19—
Lockwasher

20—
Radiator

21—
Drain
Cock
From
these
main passages, the coolant flows around
the
full
length of each combustion chamber.

After
cooling the block, the coolant passes through
ports between the block and each cylinder head.
These
ports direct most of the coolant flow around the exhaust valve area to prevent hot exhaust
gases

from
overheating the exhaust ports.

From
the cylinder heads, the water passes into a
water
manifold between each of the heads and the

water
pump. If the thermostat is closed, the coolant
is ported back to the pump where it is recirculated

back
into the pump and into the engine. After the
coolant heats enough to open the thermostat, the coolant is directed from the water manifold through
a
hose
to the top of the radiator and then through
the radiator which acts as a heat exchanger to cool the fluid. The coolant is then ported through a
hose

from
the bottom of the radiator to the pump, which

recirculates
it back to the engine.

The
cooling system is pressurized. Operating pres­
sure
is regulated by a relief valve in the radiator

cap. The
heater inlet
hose
is connected to a port on
the right bank cylinder head. The outlet
hose
is connected to the heater adapter tube on the water

pump.

c.
It is recommended when using water for coolant
that the cooling system be flushed and checked for leaks twice a year, preferably in the
fall
before
antifreeze is added and in the spring when the antifreeze is drained.

Reverse
flushing
will
aid greatly in removing rust 162

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

G and
scale, especially when used with a flushing
solution. A cleaning solution should be used to

loosen
the rust and scale before reverse flushing
the cooling system.

Flushing
is accomplished through the system in a direction
opposite
to the normal coolant flow.
This

action causes the water to get behind the corrosion

deposits
and force them out. To do this, remove
the upper and lower radiator
hoses.
Then
attach a
drain
hose
at the top of the radiator. Attach a new
piece of
hose
to the radiator
outlet
at the
bottom
and
insert the flushing gun. Connect the water
hose

to the flushing gun to a water
outlet
and the air
hose
to an air line.
Turn
on the water and when
the radiator is
full,
apply the air in short blasts,
allowing the radiator to
fill
between
blasts.
Con­
tinue this flushing operation until the water runs

clear
through the top
hose.

With
the thermostat removed, attach a leadaway
hose
to the water
hose
inlet. Also attach a length
of new
hose
to the water
outlet
connection at the
top of the engine.
Turn
the water on and
fill
the
water jacket and then apply air in short blasts.
Continue
this flushing until the water runs clear.

Also
do the hot water heater. Remove heater water

outlet
hose
from heater core. Remove inlet from 163

G
COOLING SYSTEM
engine
connections. Insert flushing gun and flush
heater core.
Care
must be taken when applying air
pressure to prevent damage to the heater core.

G-2.
Filling
Cooling System
To
fill
the cooling system, remove the
fill
cap and

fill
the tank to the top. Replace the cap and run
the
engine
at medium speed for approximately one
minute. Remove the cap and recheck the coolant level. Add more coolant if necessary to bring the level back to the top of the tank. If the cooling system is filled when the
engine
is cold, recheck the coolant level after the
engine
has warmed up.
This

will
ensure that the thermostat has opened allow­ ing complete cooling system circulation.

Always
correct any cooling system leaks before installing antifreeze. A corrosion inhibitor should be used in the cooling system to prevent the forma­
tion of rust and scale. A quality brand antifreeze containing a corrosion inhibitor should be used.

When
the antifreeze is drained in the spring, a
corrosion inhibitor should be added with the water.

Note:
Cooling system components for both V6 and

F4
engines
are shown in
Figs.
G-2 and G-3.

G-3. Draining
Cooling System

To
completely
drain
the cooling system, open the

drain
in the
bottom
of the radiator and also a

drain
on the right side of the cylinder block on the
Hurricane
F4 engine. The Dauntless V-6
engine

has two
drain
plugs, one located on each side of the cylinder block. Both plugs must be removed to
completely
drain
the cooling system.
Remove the radiator cap to break any vacuum
that may have developed.

Should
the cooling solution be lost from the system

and
the
engine
become
overheated do not
refill

the system immediately but allow the
engine
to cool or
refill
slowly while the
engine
is running. If
cold solution is poured into the radiator while the

engine
is overheated there is danger of cracking the

cylinder
block and/or cylinder head.
G-4.
Radiator Pressure
Cap

All
radiators are equipped with pressure caps which
reduce evaporation of cooling solution and make the
engines
more efficient by permitting slightly
higher operating temperatures. When operating
properly,
the pressure cap permits pressure build-up

in
the cooling system during periods of severe heat

load.
This
pressure increases the boiling point of the coolant and thus reduces overflow losses. The

effectiveness
of the cap is limited by its opening
pressure and the boiling point of the coolant (see
note
below). The pressure cap employs a spring-
loaded, rubber-faced pressure seal which presses against a seat in the radiator top tank. Spring pres­

sure
determines the opening pressure of the valve.

A
typical pressure cap is shown in Fig. G-5.

Note:
Refer to cooling system specifications (Par.

G-21)
for opening (relief) pressure when the ve­
hicle is equipped with either the
Hurricane
F4
or
Dauntless V-6 engine. If a new cap is required, always install a cap of the same type and pressure
rating
specified. It should never be altered or re­
placed by a plain cap.

A
vacuum release valve (Fig. G-5) is employed to
prevent undesirable vacuum build-up when the system
cools
down. The vacuum release valve is
held against its seat under light spring pressure.

Vacuum
in the system is relieved by the valve
which
opens
at V2 to 1 psi. [0,035 a 0,07 kg-cm2]

vacuum.
A pressure tester can be used to check and
test
the vacuum pressure rate (see Fig. G-6).
Although the mechanism of the pressure cap re­ quires no maintenance, the cap should be inspected
periodically for cleanliness and freedom of opera­ tion. The pressure cap gasket and radiator filler neck seat should also be inspected to be sure they

are
providing a proper seal. If the rubber face of
the valve is defective, a new cap should be installed.
Filler
neck reseating
tools
are commercially
avail­
able to correct minor
defects
at the surface of the seat. Follow instructions of the reseating tool manu­

facturer.

To
remove the radiator pressure cap when the
engine
coolant temperature is high or boiling, place

a
cloth over the pressure cap and
turn
counter­ clockwise about Vi
turn
until the first (pressure release)
stop
is reached. Keep the cap in this posi­
tion until all pressure is released.
Then
push cap
down and
turn
still
further until cap can be re­ moved. To install the pressure cap, place it in posi­
tion and
turn
it clockwise as far as it
will
go.

Caution:
Use extreme care in removing the radiator
pressure cap. In overheated systems, the sudden release of pressure can cause a steam flash and this

flash,
or the
loosened
cap can cause serious personal

injury.

G-5.
RADIATOR

Maintenance of the radiator consists of keeping
the exterior of the radiator core clean, the interior free from rust and scale, and the radiator free from

leaks.
Check
the cooling system fluid level and for
leaks each
2000
miles
[3.200
km.] or every 30
days, whichever occurs first.
This
exterior of the

radiator
core should be cleaned and the radiator inspected for leaks each
6000
miles
[9.600
km.]
of normal service of the vehicle. Cleaning should be performed by blowing out with air stream or water stream directed from the
rear
of the radiator.

Visual
inspection is not sufficient as the accumula­ tion of small particles of foreign material on core
surfaces can restrict cooling without closing the core openings.

Radiator
leakage occasionally results from cor­
rosion perforation of the metal but most leakage results from mechanical failure of soldered joints
when too much strain has been put on the joint.
Fractures
occur most
often
at the joint where the
radiator
inlet and
outlet
pipes are attached to the

tanks.
When the seams break, the entire soldered

joint
is
exposed
and can corrode, but breakage
rather
than corrosion is the
primary
cause of seam
leakage. Examine the radiator carefully for leaks before and after cleaning. Cleaning may uncover points of leakage already existing but plugged with
rust.
White, rusty, or colored leakage stains indicate 164

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

G

FIG.
G-4—PRESSURE TESTING COOLING SYSTEM
1—Pressure Tester C-3499 previous radiator leakage. These
spots
may not be
damp if water only or methyl-alcohol-base anti­ freeze is in the cooling system since such coolants
evaporate readily. An ethylene-glycol-base anti­ freeze shows up existing leaks as it
does
not evapo­
rate.
The radiator may be tested for leaks by using

a
Pressure Tester Tool C-4080, as shown in Fig.

G-2.

When
the pressure cap opens, the sudden surge of

vapor
or liquid must blow out through the overflow
pipe. If the overflow pipe is dented or clogged,
the pressure caused by obstruction may cause dam­
age to the radiator or
hose
connections in the cool-
1
FIG.
G-5—RADIATOR PRESSURE
CAP
1—
Pressure
Cap

2—
Overflow
Tube

3—
Pressure
Seal 4—
Vacuum
Release Valve
5—
Radiator
Neck
FIG.
G-6—TESTING RADIATOR PRESSURE
CAP
1—
Radiator
Pressure Cap

2—
Adapter

3—
Pressure
Tester C-3499 ing system. To remove clogging material, run a
flexible wire through the overflow pipe.
G-6.
Radiator Removal
and
Replacement
a.
Drain
the radiator by opening the
drain
cock

and
removing the radiator pressure cap.

b.
Remove the upper and lower
hose
clamps and

hoses
at the radiator.

c.
Remove the four cap screws, lock washers and
flat washers that secure the radiator to the radiator
body support. Remove the radiator.

d.
To replace the radiator, reverse the removal

procedure.

G-7.
Radiator
Hoses
and
Heater Hoses

Air,
heat, and water deteriorate radiator and heater

hoses
in two ways: by hardening or cracking which
destroys flexibility and causes leaks; by softening
and
swelling which produces lining failure and
hose

rupture
and clogging. Examine
hoses
spring and

fall
for possible need of replacement or tightening.

If
hoses
are collapsed, cracked, or indicate a
soft

condition on the inside they should be replaced.
Correct
installation of a new heater
hose
is impor­
tant to prevent contact between the
hose
and the
exhaust manifold. On the
Hurricane
F4 engine the
molded curved end of the
hose
connects to the
hot water intake of the heater; the flexible end to the hot water valve on top of the cylinder head.
On
the Dauntless V-6 engine the heater inlet
hose

is connected to the
rear
of the intake manifold 165

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

G
cation period. It is
good
preventive maintenance to
replace a badly frayed, worn or cracked fan belt
before it breaks in operation.

To
replace the fan belt,
loosen
the attaching
bolts

at each generator or alternator brace-to-engine mounting and pivot the alternator or generator to­

ward
the
engine
to gain slack needed to install the new belt Remove the old belt. Position the new
belt over the fan pulley, over the crankshaft pulley,
then over the generator or alternator pulley.
Pull
the generator or alternator away from the
engine

until
belt tension is
firm.
Then tighten the generator

or
alternator mounting
bolts
and check the tension
as indicated above. Reset the generator or alternator as necessary for correct belt tension.
Finally,
torque
the generator or alternator mounting
bolts
25 to 35 lb-ft. [3,4 a 4,8 kg-m.].

Note:
On the Dauntless V-6
engine
when adjusting
the fan belt tension, the alternator mounting
bolts

should be torqued 30 to 40 lb-ft. [4,14 to 5,53

kg-m.].
If a fan belt tension
gauge
(W-283) is
avail­

able, proper tension should be 80 pounds [36,2 kg.].

G-l
9. Engine Overheating

An
engine
will
not be damaged by high coolant
temperatures unless the coolant boils. The pres­

surized
cooling system on the 'Jeep' vehicles raises the boiling point of the coolant solution. Should
overheating be encountered, and the fault is be­
lieved to be in the cooling system check for the
following:

a.
Proper coolant level. See
Filling
Cooling Sys­
tem Par. G-2.
b. Poor air flow.
Check
for dirty radiator core. (See Radiator Par. G-5).
Check
for faulty belt
pulley operation, worn or
loose
fan belt, or dam­ aged fan.
Clean,
repair, replace or adjust as neces­

sary.

c. Foaming coolant.
Check
for air leaks at water
pump,
hose
connection and filler cap. Tighten, re­

pair
or replace as necessary.

d.
Surging or "after boil".
Check
pressure cap and
replace if valves or gasket are faulty.
e.
External
leaks.
Check
the following for leaks:
Hoses and clamps, water pump, radiator, head gas­
ket, core plugs and drain cocks, as well as the cylin­ der head or block for
cracks.

f.
Internal
leaks.
Check
for faulty head gasket,
cracked
cylinder head or block.
g. Poor coolant flow.
Check
hose
condition, water pump, fan belt, and repair or replace as necessary. Inspect block for rust or scale, and clean and flush
the system, if necessary.

h.
Check
the temperature
gauge.
169

G
COOLING SYSTEM G-20.
SERVICE DIAGNOSIS

SYMPTOMS
PROBABLE REMEDY

Overheating:
Lack
of Coolant Refill radiator
Thermostat inoperative . Replace thermostat
Water
pump inoperative. Overhaul or replace
Incorrect
ignition or valve timing. Set
engine
timing
Excessive piston blowby Check pistons, rings and cylinder walls
Fan
belt
broken or badly worn Replace
belt

Radiator
clogged
Reverse flush and clean
Air
passages
in core
clogged
Clean with water and air pressure
Excessive carbon formation. Remove carbon from cylinder head(s) Muffler
clogged
or
bent
exhaust
pipe
Replace damaged part

Loss
of Cooling
Liquid:
Loose
hose
connections
Tighten
connections

Damaged
hose
Replace
hose

Leaking
water pump Overhaul or replace

Leak
in radiator Remove and repair
Leaky
cylinder head
gasket
Replace
gasket
Crack
in cylinder block. Small crack can be closed with
Radiator
or Block Sealer

G-21. COOLING SYSTEM SPECIFICATIONS

Radiator
Cap:
Relief
Pressure

Vacuum
Valve Release.
Thermostat:
Rating

Starts to Open

Fully
Open

Water
Pump:
Type.

Drive

Radiator:

Type

Cooling System Capacity: Without Heater

With
Heater..

Fan:
Number of Blades Diameter

Drive
Belt: Angle of V

Length
Width
HURRICANE
F4
7 and 15 psi. [0,5 kg-cm2 and 1,05 kg cm2]
lA to 1 psi. [0,04 a 0,07 kg-cm2]

190°F.
[87,8°C]
180°F.
[82°C]

202°F.
[94°C]

Centrifugal
V-Belt

Tube
8s Fin
11 qt. [10,4 ltr.] 12 qt. [11,5 ltr.]
15" [38 cm.]
38°

42%" [108 cm.] [1,74 cmJ
DAUNTLESS
V-6 15 psi. [1,05 kg-cm2]
1 psi. [0,07 kg-cm2]

190°F.
[87,8°C]
180°F.
[82°C]

202°F.
[94°C]

Centrifugal
V-Belt

Tube
& Fin
9 qt. [8.5 ltr.]
10 qt. [9,4 ltr.]
4

\SbA"
[39,7 cm.]

38°

43.92"
[111,5
cm.] Vg"
[0.952
cm.] G-22. ANTIFREEZE CHERT

Quarts
i
Quarts
Ethylene Glycol

U.S.
Imperial
Liters
Fahr.
Cent.

10-Quart
System

2
m
2

16°
-
8.8°

3
2V2
2%
4°

-15.5°

4
3H
-12°

-24.4°

5 4M -34°

-36.6°

6
5

5Vs
-62°

-52.2°

11-Quart
System

2 2

18° -
7.6°

3 2H
2%
8°

-13.3°

4
3%
-
6°

:
-21.10

5 4M 4M -23°

-30.5°

6
5

SVs
-47°

-43.8°

12-Quart
System

2
1 m 2 1

19° ;
- 7.2°

3
2*A
10°
!
-12.2°

4
I
3H
3M 0°
;
-17.7°

5 !
4M 4^ :
-15°

s
-26.1°

6 1 5
5%
-34°

-36.6°
170

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H

FIG.
H-l—ENGINE
GROUND
STRAP—F4
ENGINE
Fig.
H-l, is tight at both connections. If
these

connections are
loose
-
or
dirty,
hard
starting or
failure
to start may result.

H-3.
Ignition System

The
ignition system consists of the battery, ignition

switch,
ignition coil ballast resistor (V-6 engine
only),
ignition coil, ignition distributor,
spark
plugs,

and
the low and high tension wiring.
Electrical

energy is obtained from the battery while cranking
and
from the alternator after the engine is running.

These
supply circuits must be considered part of
the ignition system.

The
ignition system furnishes the
spark
-for the

spark
plugs. The
spark
must occur in each cylinder
at exactly the proper time. To accomplish this, the following units are required.

a.
The battery, supplying the electrical energy.
Note: 'Jeep* vehicles equipped with Dauntless

V-6
engines have a ballast resistor connected be­ tween the ignition switch and the positive (+)

terminal
of the coil. The ballast resistor limits to
a
safe maximum the
primary
current flow through
the coil and the distributor contact points.

b.
The ignition coil, transforming the battery low
tension current to high tension current that jumps
the
spark
plug gap in the cylinders under com­
pression.

c.
The distributor, delivering the
spark
to the

proper
cylinders and incorporates the mechanical

breaker,
that
opens
and closes the
primary
circuit at the exact time.

d.
The
spark
plugs, providing the gap in the engine
cylinders.

e. The wiring, connecting the various ignition
units.

f. The ignition switch controling the battery
current
when it is desired to start or
stop
the engine.
g. The firing order for the
Hurricane
F4 engine is
1-3-4-2.
Cylinder
No. 1 is the cylinder closest to the

radiator.

h.
The firing order for the Dauntless V-6 engine
is
1-6-5-4-3-2.
Cylinders
1-3-5 are on the left bank

and
cylinders 2-4-6 are on the right bank. H-4.
PRIMARY
CIRCUIT

Before testing the
primary
circuit,
make certain
that the battery is satisfactory or install a fully

charged
battery for the
primary
circuit
tests. Also,

check
the starter motor for excessive voltage drop

and
check the starter motor itself for excessive
draw.

a.
Measure the voltage at the coil
primary
termi­

nals
while cranking the engine with the starter
motor. If the voltage is less than 9 volts the trouble

will
be found in the
primary
circuit.
If there is no voltage at all, check for a break in the
primary

circuit,
possibly in the coil
primary
winding.

b.
To check the
primary
circuit,
turn
the ignition
on,
turn
the engine until the points are closed, and
then measure the voltage drop across each portion
of the circuit with a voltmeter.
Note: Most voltage drops
will
be found at the con­
nections of wires to terminals as
dirt,
oxidation etc. can cause excessive resistance at
these
points.

Measure
voltage drops in wires to take this into
account.

c.
Connect the voltmeter from the battery cable

terminal
on the starter solenoid to the battery

terminal
of the coil
primary.
If the voltmeter reads more than 0.2 volt, perform the checks given in
steps, d, e, and f following.

d.
Connect the voltmeter from the solenoid termi­

nal
to the battery terminal of the ignition switch.
If
the voltmeter reads more than .05 volt, check

and
clean the connections at solenoid, light switch,
and
ignition switch.
e. If the voltmeter reading in
step
d is less than .05 volt, connect the voltmeter from the battery

terminal
to the ignition terminal on the ignition
switch.
If the voltage drop is more than 0.1 volt,

repair
or replace the ignition switch.
f. If the voltage drop in
step
e is not more than 0.1 volt, connect the voltmeter from the ignition

terminal
of the ignition switch to the battery termi­

nal
of the coil
primary.
If the voltmeter reads more

than
.05 volt, clean and tighten the connections

and
check again. If the voltmeter again reads more

than
.05 volt, replace the wire.
g. Connect the voltmeter from the distributor
primary
terminal on the coil to the coil terminal on
the distributor. Voltage drop should not exceed .05 volt.
Clean
and tighten connections if necessary.

h.
Connect the voltmeter from the coil terminal
on the distributor to a clean,
paint-
free spot on the

distributor
body. The reading should not exceed .05
volt. If more, it indicates excessive resistance
through the points or in the distributor internal connections.
Clean
and align the points and make

sure
the breaker arm connection to the
primary

terminal
as well as the stationary contact point mounting in the body is clean and tight.

i.
Open the points and check the voltmeter. It
should read close to peak voltage. Low voltage in­ dicates that a circuit through the distributor (a

short)
exists while the points are open.

j.
Disconnect the condenser lead and open the points. A jump to
full
voltage indicates a short in 173