display JEEP GRAND CHEROKEE 2011 Owner handbook (in English)

Page 136 of 350


FCW Unavailable Warning
If the system turns off, and the EVIC displays
“ACC/FCW Unavailable, Vehicle System Error”,
there may be a temporary malfunction that
limits FCW functionality. Although the vehicle is
still drivable under normal conditions, FCW will
be temporarily unavailable. If this occurs, try
activating FCW again later, following a key
cycle. If the problem persists, see your autho-
rized dealer.
Service FCW Warning
If the system turns off, and the EVIC displays
“ACC/FCW Unavailable Service Radar Sen-
sor”, it indicates there is an internal system
fault. Although the vehicle is still drivable under
normal conditions, have the system checked
by an authorized dealer.
PARKSENSEPARK ASSIST —
IF EQUIPPED
The ParkSense Park Assist system provides
visual and audible indications of the distance
between the rear and/or front fascia and a
detected obstacle when backing up or moving forward, e.g. during a parking maneuver. Refer
to ParkSense
System Usage Precautions for
limitations of this system and recommenda-
tions.
ParkSense will retain the last system state
(enabled or disabled) from the last ignition
cycle when the ignition is changed to the
ON/RUN position. ParkSense can be active
only when the shift lever is in REVERSE or
DRIVE.
If ParkSense is enabled at one of these shift
lever positions, the system will remain active
until the vehicle speed is increased to approxi-
mately 11 mph (18 km/h) or above. The system
will become active again if the vehicle speed is
decreased to speeds less than approximately
10 mph (16 km/h).
ACC/FCW Unavailable Warning
132

Page 137 of 350


ParkSenseSensorsThe four ParkSense sensors, located in the
rear fascia/bumper, monitor the area behind the
vehicle that is within the sensors’ field of view.
The sensors can detect obstacles from ap-
proximately 12 in (30 cm) up to 79 in (200 cm)
from the rear fascia/bumper in the horizontal
direction, depending on the location, type and
orientation of the obstacle.
The six ParkSense sensors, located in the
front fascia/bumper, monitor the area in front of
the vehicle that is within the sensors’ field of
view. The sensors can detect obstacles from
approximately 12 in (30 cm) up to 47 in
(120 cm) from the front fascia/bumper in the
horizontal direction, depending on the location,
type and orientation of the obstacle.ParkSense Warning DisplayThe ParkSense Warning screen will only be
displayed if Sound and Display is selected from
the Customer- Programmable Features section
of the Electronic Vehicle Information Center
(EVIC). Refer to “Electronic Vehicle Information
Center (EVIC)/Personal Settings (Customer-
Programmable Features)” in “Understanding
Your Instrument Panel” for further information.
The ParkSense Warning Display is located in
the Instrument cluster’s EVIC display. It pro-
vides both visual and audible warnings to indi-
cate the distance between the rear fascia/
bumper and/or front fascia/bumper and the
detected obstacle.ParkSense DisplayThe warning display will turn ON indicating the
system status when the vehicle is in REVERSE
or when the vehicle is in DRIVE and an obstacle
has been detected.
Park Assist Display
Park Assist ON
133

Page 138 of 350


The system will indicate a detected obstacle by
showing three solid arcs and will produce a
one-half second tone. As the vehicle moves
closer to the object the EVIC display will show
fewer arcs and the sound tone will change from
slow, to fast, to continuous.The vehicle is close to the obstacle when the
EVIC display shows one flashing arc and
sounds a continuous tone. The following chart
shows the warning alert operation when the
system is detecting an obstacle:
Slow Tone
Fast Tone
Continuous Tone
134

Page 139 of 350


WARNING ALERTS
Rear Distance (in/cm) Greater than 79 in (200 cm)79-39 in
(200-100 cm) 39-25 in
(100-65 cm) 25-12 in
(65-30 cm) Less Than 12 in
(30 cm)
Front Distance (in/cm) Greater than 47 in (120 cm)47-39 in
(120-100 cm) 39-25 in
(100-65 cm) 25-12 in
(65-30 cm) Less Than 12 in
(30 cm)
Audible Alert (Chime) None Single 1/2 Second ToneSlow Fast Continuous
Display Message Park Assist ON Warning Object DetectedWarning Object
Detected Warning Object
Detected Warning Object
Detected
Arcs None 3 Solid (Continuous)3 Slow Flashing 2 Slow Flashing 1 Slow Flashing
Radio Mute No Yes Yes Yes Yes
NOTE:
ParkSense will MUTE the radio, if on, when
the system is sounding an audio tone.
Enabling and Disabling ParkSense ParkSensecan be enabled and disabled with
a switch located in the switch bank of the
instrument panel or through the Customer-
Programmable Features section of the EVIC.
The available choices are: OFF, Sound Only, or
Sound and Display. Refer to “Electronic Vehicle
Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Un-
derstanding Your Instrument Panel” for further
information.
When the Park Sense switch is
pressed to disable the system, the
instrument cluster will display the
“PARK ASSIST OFF” message for
approximately five seconds. Refer
to “Electronic Vehicle Information
Center (EVIC)” in “Understanding Your Instru-
ment Panel” for further information. When the
shift lever is moved to REVERSE or to DRIVE (at
or below 11 mph/18 km/h) and the system is disabled, the EVIC will display the “PARK AS-
SIST OFF” message for as long as the vehicle is
in REVERSE or for five seconds when the
vehicle is in DRIVE.
The ParkSense
switch LED will be ON when
ParkSense is disabled or defective. The Park-
Sense switch LED will be OFF when the
system is enabled.
The ParkSense system uses four sensors lo-
cated in the rear bumper fascia to scan for
obstacles up to 79 in (200 cm) away from the
rear bumper fascia. The ParkSense system
135

Page 140 of 350


uses six sensors located in the front bumper
fascia to scan for obstacles up to 47 in
(120 cm) away from the front bumper fascia.
The warning display located above in the In-
strument Cluster’s EVIC provides both visible
and audible warnings to indicate the range of
the object.
Service the ParkSensePark Assist
System
When the ParkSense Park Assist System is
malfunctioning, the instrument cluster will actu-
ate a single chime, once per ignition cycle. The
instrument cluster will display the “REAR SEN-
SOR BLINDED” message when any of the rear
sensor(s) is blocked by snow, mud, or ice and
the vehicle is shifted into REVERSE or DRIVE.
The instrument cluster will display the “CLEAN
PARK ASSIST SENSORS” message when any
of the front sensor(s) is blocked by snow, mud,
or ice and the vehicle is shifted into REVERSE
or DRIVE. The instrument cluster will display the
“SERVICE PARK ASSIST SYSTEM” message
when any of the rear or front sensors are
damaged and require service. When the shift
lever is moved to REVERSE or DRIVE and the system has detected a faulted condition, the
EVIC will display the “CLEAN PARK ASSIST
SENSORS” or the “SERVICE PARK ASSIST
SYSTEM” message for as long as the vehicle is
in REVERSE or DRIVE (at speeds less than
11 mph/18 km/h). Under this condition Park-
Sense
will not operate. Refer to “Electronic
Vehicle Information Center (EVIC)” in “Under-
standing Your Instrument Panel” for further in-
formation.
If the “CLEAN PARK ASSIST SENSORS” mes-
sage appears in the Electronic Vehicle Informa-
tion Center (EVIC) and the rear fascia/bumper
or front fascia/bumper is clean and clear of
snow, ice, mud, dirt or other obstruction, see
your authorized dealer. If “SERVICE PARK AS-
SIST SYSTEM” appears in the EVIC, see your
authorized dealer.
Cleaning the ParkSense SystemClean the ParkSense sensors with water, car
wash soap and a soft cloth. Do not use rough or
hard cloths. Do not scratch or poke the sen-
sors. Otherwise, you could damage the sen-
sors.
ParkSense System Usage
Precautions
NOTE:
• Ensure that the front and rear bumper are
free of snow, ice, mud, dirt and debris to
keep the ParkSense system operating
properly.
• Jackhammers, large trucks, and other vi-
brations could affect the performance of
ParkSense .
• When you turn ParkSense off, the instru-
ment cluster will display “PARK ASSIST
OFF.” Furthermore, once you turn Park-
Sense off, it remains off until you turn it
on again, even if you cycle the ignition
key.
• When you move the shift lever to the
REVERSE or DRIVE position and Park-
Sense is turned off, the instrument clus-
ter will display “PARK ASSIST OFF” mes-
sage for as long as the vehicle is in
REVERSE and when the vehicle is in
DRIVE at or below 11 mph (18 km/h).
• ParkSense , when on, will MUTE the radio
when it is sounding a tone.
136

Page 141 of 350


•Clean the ParkSense sensors regularly,
taking care not to scratch or damage
them. The sensors must not be covered
with ice, snow, slush, mud, dirt or debris.
Failure to do so can result in the system
not working properly. The ParkSense 
system might not detect an obstacle be-
hind or in front of the fascia/bumper, or it
could provide a false indication that an
obstacle is behind or in front of the fascia/
bumper.
• Objects such as bicycle carriers, trailer
hitches, etc., must not be placed within
12 in (30 cm) from the rear fascia/bumper
while driving the vehicle. Failure to do so
can result in the system misinterpreting a
close object as a sensor problem, caus-
ing the “SERVICE PARK ASSIST SYS-
TEM” message to be displayed in the
instrument cluster.CAUTION!
• ParkSense is only a parking aid and it is
unable to recognize every obstacle, includ-
ing small obstacles. Parking curbs might be
temporarily detected or not detected at all.
Obstacles located above or below the sen-
sors will not be detected when they are in
close proximity.
• The vehicle must be driven slowly when
using ParkSense in order to be able to
stop in time when an obstacle is detected.
When backing up, it is recommended that
the driver looks over his/her shoulder when
using ParkSense .WARNING!
• Drivers must be careful when backing up
even when using the ParkSense Park
Assist System. Always check carefully be-
hind your vehicle, look behind you, and be
sure to check for pedestrians, animals,
other vehicles, obstructions, and blind
spots before backing up. You are respon-
sible for safety and must continue to pay
attention to your surroundings. Failure to
do so can result in serious injury or death.
(Continued)
137

Page 142 of 350


WARNING!(Continued)
• Before using the ParkSense Park Assist
System, it is strongly recommended that
the ball mount and hitch ball assembly is
disconnected from the vehicle when the
vehicle is not used for towing. Failure to do
so can result in injury or damage to ve-
hicles or obstacles because the hitch ball
will be much closer to the obstacle than the
rear fascia when the warning display turns
on the single flashing arc and sounds the
continuous tone. Also, the sensors could
detect the ball mount and hitch ball assem-
bly, depending on its size and shape, giving
a false indication that an obstacle is behind
the vehicle.PARKVIEW REAR BACK UP
CAMERA — IF EQUIPPED
Your vehicle may be equipped with the Park-
View Rear Back Up Camera that allows you to
see an on-screen image of the rear surround-
ings of your vehicle whenever the shift lever is
put into REVERSE. The image will be displayed
on the Navigation/Multimedia radio display
screen along with a caution note to “check
entire surroundings” across the top of the
screen. After five seconds this note will disap-
pear. The ParkView camera is located on the
rear of the vehicle above the rear License plate. When the vehicle is shifted out of REVERSE, the
rear camera mode is exited and the navigation
or audio screen appears again.
When displayed, static grid lines will illustrate
the width of the vehicle while a dashed center-
line will indicate the center of the vehicle to
assist with aligning to a hitch/receiver. The
static grid lines will show separate zones that
will help indicate the distance to the rear of the
vehicle. The following table shows the approxi-
mate distances for each zone:
Zone Distance to the rear of the vehicle
Red 0-1ft(0-30cm)
Yellow 1 f t-3ft(30cm-1m)
Green 3 ft or greater (1 m or greater)
138

Page 157 of 350


4
UNDERSTANDING YOUR INSTRUMENT
PANEL
•INSTRUMENT PANEL FEATURES ................. 156
• INSTRUMENT CLUSTER ...................... 157
• INSTRUMENT CLUSTER DESCRIPTIONS ............ 158
• ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . 163
• Electronic Vehicle Information Center (EVIC) Displays . . 164
• EVIC White Telltale Lights ................... 167
• EVIC Amber Telltale Lights .................. 168
• EVIC Red Telltale Lights .................... 169
• Engine Oil Change Indicator System ............ 171
• Fuel Economy .......................... 171
• Vehicle Speed .......................... 172
• Trip Info .............................. 172
• Units ............................... 173
• Vehicle Info (Customer Information Features) ....... 173
• TirePSI .............................. 173
153

Page 158 of 350


•Keyless Enter-N-Go Display — If Equipped ......... 174
• Compass / Temperature Display ............... 174
• Customer-Programmable Features (System Setup) .... 177
• SOUND SYSTEMS .......................... 181
• UNIVERSAL CONSUMER INTERFACE (UCI) 1.0 —
IF EQUIPPED ............................ 181
• Connecting The iPod or External USB Device ...... 181
• Using This Feature ....................... 181
• Controlling The iPod or External USB Device Using
Radio Buttons .......................... 182
• Play Mode ............................ 182
• List Or Browse Mode ...................... 183
• Bluetooth Streaming Audio (BTSA) ............. 184
• STEERING WHEEL AUDIO CONTROLS ............. 184
• Radio Operation ......................... 185
• CD Player ............................. 185
• CD/DVD DISC MAINTENANCE .................. 185
• RADIO OPERATION AND MOBILE PHONES .......... 185
154

Page 163 of 350


than 30 mph (48 km/h), see your authorized
dealer as soon as possible to have the problem
diagnosed and corrected.
NOTE:
•The “ESC Off Indicator Light” and the
“ESC Activation/Malfunction Indicator
Light” come on momentarily each time
the ignition switch is turned to ON/RUN.
• Each time the ignition is turned to ON/
RUN, the ESC system will be ON even if it
was turned off previously.
• The ESC system will make buzzing or
clicking sounds when it is active. This is
normal; the sounds will stop when ESC
becomes inactive following the maneuver
that caused the ESC activation.
5. TOW/HAUL Indicator Light —
If Equipped This light will illuminate when the
TOW/HAUL button has been se-
lected. The TOW/HAUL button is
located in the center of the instru-
ment panel (below the climate
controls). 6. Turn Signal Indicator
The arrows will flash with the exterior turn
signals when the turn signal lever is op-
erated. A tone will chime, and an EVIC
message will appear if the turn signals are left
on for more than 1 mile (1.6 km).
7. High Beam Indicator Indicates that headlights are on high
beam.
8. Front Fog Light Indicator — If Equipped This indicator will illuminate when the
front fog lights are on.
9. Hill Descent Control Indicator Light —
If Equipped The symbol indicates the status of
the Hill Decent Control (HDC) fea-
ture. The lamp will be on solid
when HDC is armed. HDC can
only be armed when the transfer
case is in the “4WD Low” position
and the vehicle speed is less then 30 mph
(48 km/h). If these conditions are not met while
attempting to use the HDC feature, the HDC
indicator lamp will flash on/off. 10. Electronic Vehicle Information Center
(EVIC) Display/Odometer Display
The odometer display shows the total distance
the vehicle has been driven.
Regulations require that upon transfer of ve-
hicle ownership, the seller certify to the pur-
chaser the correct mileage that the vehicle has
been driven. If your odometer needs to be
repaired or serviced, the repair technician
should leave the odometer reading the same as
it was before the repair or service. If s/he
cannot do so, then the odometer must be set at
zero, and a sticker must be placed in the door
jamb stating what the mileage was before the
repair or service. It is a good idea for you to
make a record of the odometer reading before
the repair/service, so that you can be sure that
it is properly reset, or that the door jamb sticker
is accurate if the odometer must be reset at
zero.
When the appropriate conditions exist, this
display shows the Electronic Vehicle Informa-
tion Center (EVIC) messages. Refer to “Elec-
tronic Vehicle Information Center”.
159

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 ... 80 next >