JEEP LIBERTY 2006 KJ / 1.G Owners Manual
Page 311 of 424
MAINTAINING YOUR VEHICLE
CONTENTS
3.7L Engine ...........................314
2.8L Turbo Diesel Engine .................315
Onboard Diagnostic System — OBD II ........316
â–« Loose Fuel Filler Cap Message ............316
Emissions Inspection And Maintenance
Programs ............................317
Replacement Parts ......................318
Dealer Service .........................318
Maintenance Procedures ..................319 â–«
Engine Oil ..........................319
â–« Drive Belts — Check Condition And Tension . . 323
â–« Spark Plugs .........................324
â–« Catalytic Converter ....................324
â–« Crankcase Emission Control System ........326
â–« Air Cleaner Filter .....................326
â–« Maintenance-Free Battery ................326
â–« Air Conditioner Maintenance .............327
â–« Power Steering Fluid Check ..............328
7
Page 312 of 424
â–«Driveline And Steering Component
Lubrication ..........................329
â–« Body Lubrication .....................329
â–« Windshield Wiper Blades ................330
â–« Windshield Washers ...................330
â–« Exhaust System ......................331
â–« Cooling System .......................332
â–« Hoses And Vacuum/Vapor Harnesses .......337
â–« Brake System ........................337
â–« Automatic Transmission ................340
â–« Hydraulic Clutch Fluid —
Manual Transmission ..................342
â–« Manual Transmission ..................342
â–« Transfer Case ........................342 â–«
Front/Rear Axle Fluid ..................343
â–« Appearance Care And Protection From
Corrosion ...........................345
Fuse Panel ...........................349
â–« Interior Fuses ........................349
â–« Underhood Fuses
(Power Distribution Center) ..............351
Vehicle Storage ........................355
Replacement Bulbs ......................356
Bulb Replacement ......................356
â–« Head Light ..........................356
â–« Front Turn Signal .....................357
â–« Front Fog Light (Front Fascia Mounted) .....358
â–« Light Bar ...........................359
312 MAINTAINING YOUR VEHICLE
Page 313 of 424
â–«Rear Tail, Stop, Turn Signal, And Back-Up
Lights .............................360
â–« Center High Mounted Stop Light (CHMSL) . . . 361
Fluid Capacities ........................362
Fluids, Lubricants, And Genuine Parts ........363
â–« Engine .............................363
â–« Chassis ............................364
MAINTAINING YOUR VEHICLE 313
7
Page 314 of 424
3.7L ENGINE
314 MAINTAINING YOUR VEHICLE
Page 315 of 424
2.8L TURBO DIESEL ENGINE
MAINTAINING YOUR VEHICLE 315
7
Page 316 of 424
ONBOARD DIAGNOSTIC SYSTEM — OBD II
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors
the performance of the emissions, engine, and automatic
transmission control systems. When these systems are
operating properly, your vehicle will provide excellent
performance and fuel economy, as well as engine emis-
sions well within current government regulations.
If any of these systems require service, the OBD II system
will turn on the “Malfunction Indicator Light.” It will
also store diagnostic codes and other information to
assist your service technician in making repairs. Al-
though your vehicle will usually be drivable and not
need towing, see your dealer for service as soon as
possible.CAUTION!
•Prolonged driving with the “Malfunction Indica-
tor Light” on could cause further damage to the
emission control system. It could also affect fuel
economy and driveability. The vehicle must be
serviced before any emissions tests can be per-
formed.
•If the “Malfunction Indicator Light” is flashing
while the engine is running, severe catalytic con-
verter damage and power loss will soon occur.
Immediate service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“GAS CAP” message will be displayed in the odometer
(located on the instrument cluster). Replace, or tighten
316 MAINTAINING YOUR VEHICLE
Page 317 of 424
the fuel filler cap properly to turn the message off (light
will time out). If the problem continues, the message will
appear the next time the vehicle is started.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and
Maintenance) requirement, this check verifies the
following: the MIL (Malfunction Indicator Lamp)
is functioning and is not on when the engine is running,
and that the OBD (On Board Diagnostic) system is ready
for testing.
Normally, the OBD system will be ready. The OBD
system may notbe ready if your vehicle was recently
serviced, if you recently had a dead battery, or a battery replacement. If the OBD system should be determined
not ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key actuated test
which you can use prior to going to the test station. To
check if your vehicle’s OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
MAINTAINING YOUR VEHICLE 317
7
Page 318 of 424
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn off the
ignition key or start the engine. This means that your
vehicle’s OBD system is not readyand you should not
proceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn off the ignition key or start
the engine. This means that your vehicle’s OBD system
is ready and you can proceed to the I/M station.
If your OBD system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
Regardless of whether your vehicle’s OBD system is
ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your
vehicle serviced before going to the I/M station. The I/M
station can fail your vehicle because the MIL symbol is on
with the engine running.
REPLACEMENT PARTS
Use of genuine Mopar
parts for normal/scheduled
maintenance and repairs is highly recommended to in-
sure the designed performance. Damage or failures
caused by the use of non-Mopar parts for maintenance
and repairs will not be covered by the manufacturer’s
warranty.
DEALER SERVICE
Your dealer has the qualified service personnel, special
tools and equipment to perform all service operations in
an expert manner. Service Manuals are available which
include detailed service information for your vehicle.
Refer to these manuals before attempting any procedure
yourself.
318 MAINTAINING YOUR VEHICLE
Page 319 of 424
NOTE:Intentional tampering with emissions control
systems can result in civil penalties being assessed
against you.
WARNING!
You can be badly injured working on or around a
motor vehicle. Do only that service work for which
you have the knowledge and the proper equipment.
If you have any doubt about your ability to perform
a service job, take your vehicle to a competent
mechanic.
MAINTENANCE PROCEDURES
The pages that follow contain the requiredmaintenance
services determined by the engineers who designed your
vehicle.
Besides the maintenance items for which there are fixed
maintenance intervals, there are other items that should
operate satisfactorily without periodic maintenance.
However, if a malfunction of these items does occur, it
could adversely affect the engine or vehicle performance.
These items should be inspected if a malfunction is
observed or suspected.
Engine Oil
Checking Oil Level
To assure proper lubrication of your vehicle’s engine, the
engine oil must be maintained at the correct level. Check
the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE 319
7
Page 320 of 424
The best time to check the engine oil level is about 5
minutes after a fully warmed engine has been shut off, or
before starting the engine after it has sat overnight.
Checking the oil while the vehicle is on level ground will
improve the accuracy of the oil level readings. Maintain
the oil level between the ADD and SAFE markings on the
dipstick. Adding 1 U.S. Quart (0.95L) of oil when the
reading is at the ADD mark will result in a SAFE reading
on these engines.
CAUTION!
Overfilling or underfilling the crankcase will cause
aeration or loss of oil pressure. This could damage
your engine.
Change Engine Oil
Road conditions as well as your kind of driving affect the
interval at which your oil should be changed. Check the
following to determine if any apply to you:
•Day or night temperatures are below 32°F (0°C)
•Stop and go driving
•Extensive engine idling
•Driving in dusty conditions
•Short trip driving of less than 10 miles (16.2 km)
•More than 50% of your driving is at sustained high
speeds during hot weather, above 90°F (32°C)
•Taxi, Police, or delivery service (commercial service)
•Trailer towing
•Off-road or desert driving
320 MAINTAINING YOUR VEHICLE