torque JEEP WRANGLER 2022 Owners Manual

CAUTION!
Do not over tighten Torx screws. Damage to
the retainers will occur.Torque Speci -
fication For Torx Screw Maximum Minimum
119.5 in-lbs 150.5 in-lbs 106.2 in-lbs 13.5 N·m 17.0 N·m 12.0 N·m
CAUTION!
Failure to follow the next steps could result in
damage to the Soft Top or vehicle.
2

21_JL_OM_EN_USC_t.book Page 85

:$51,1* (Continuedyf
Target Torque
Specification For Torx Fas -
teners Maximum Minimum
79.6 in-lbs (9 N·myf 87.6 in-lbs
(9.9 N·myf 71.7 in-lbs
(8.1 N·myf
CAUTION!
Do not overtighten the screws. You can strip
the screws if they are overtightened.
1 — Front Door Rail
2 — Rear Door Frame
2

21_JL_OM_EN_USC_t.book Page 99

:$51,1*
In the ESC “Full Off” mode, the engine
torque reduction and stability features are
disabled. Therefore, enhanced vehicle
stability offered by the ESC system is
unavailable. In an emergency evasive
maneuver, the ESC system will not engage
to assist in maintaining stability. ESC “Full
Off” mode is intended for off-highway or
off-road use only.
The Electronic Stability Control (ESCyf
cannot prevent the natural laws of physics
from acting on the vehicle, nor can it
increase the traction afforded by prevailing
road conditions. ESC cannot prevent all
accidents, including those resulting from
excessive speed in turns, driving on very
slippery surfaces, or hydroplaning. ESC also
cannot prevent collisions.

&$87,21
,IDWUDQVPLVVLRQIOXLGOHDNRFFXUVYLVLWDQ
DXWKRUL]HGGHDOHULPPHGLDWHO\6HYHUHWUDQV-
mission damage may occur. An authorized
dealer has the proper tools to adjust the fluid
level accurately.
CAUTION!
Using a transmission fluid other than FCA rec -
ommended fluid may cause deterioration in
transmission shift quality and/or torque con -
verter shudder Ú page 442.
8

21_JL_OM_EN_USC_t.book Page 391

TEC\b 
\f SPECIFICATIONS
VE\b \fE IDENTIFICATION NUMBER
The Vehicle Identification Number (VINyfLVIRXQG
on the left front corner of the A-pillar, visible
from outside of the vehicle through the
windshield.
Vehicle Identification Number

NOTE:
It is illegal to remove or alter the VIN plate.
BRAKE SYSTEM
Your vehicle is equipped with dual hydraulic
brake systems. If either of the two hydraulic
systems loses normal capability, the remaining
system will still function. However, there will be some loss of overall braking effectiveness. You
may notice increased pedal travel during
application, greater pedal force required to slow
or stop, and potential activation of the Brake
Warning Light.
In the event power assist is lost for any reason
(i.e., repeated brake applications with the
engine offyfWKHEUDNHVZLOOVWLOOIXQFWLRQ
However, the effort required to brake the
vehicle will be much greater than that required
with the power system operating.
W\b\f AND TIRE TORQUE SPECIFICATIONS
Proper lug nut/bolt torque is very important to
ensure that the wheel is properly mounted to
the vehicle. Any time a wheel has been removed
and reinstalled on the vehicle, the lug nuts/
bolts should be torqued using a properly
calibrated torque wrench using a six sided (hexyf
deep wall socket.
TORQUE SPECIFICATIONS
**Use only authorized dealer recommended lug nuts/
bolts and clean or remove any dirt or oil before tightening.
Inspect the wheel mounting surface prior to
mounting the tire and remove any corrosion or
loose particles.
Spare Tire Torque Specifications
**Use only authorized dealer recommended lug nuts/
bolts and clean or remove any dirt or oil before tightening.
Lug Nut/Bolt
Torque **Lug Nut/
Bolt Size Lug Nut/Bolt
Socket Size
130 Ft-Lbs (176 N·myf M14 x 1.50 22 mm
Lug Nut/Bolt Torque **Lug Nut/
Bolt Size Lug Nut/Bolt
Socket Size
59 Ft-Lbs (80 N·myf M14 x 1.50 22 mm
9

21_JL_OM_EN_USC_t.book Page 431