oil temperature KIA CARNIVAL 2007 User Guide
Page 151 of 1575
2007 > 2.7L V6 GASOLINE >
SPECIFICATION
IGNITION SYSTEM
Items Specification
Ignition coil Primary resistance
0.715 ± 0.015 Ω
Secondary resistance -
Spark plugs NGK ILFR5B11
Plugs Gap 1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in)
STARTING SYSTEM Items Specification
Starter Rated voltage
12 V, 1.2 kW
No. of pinion teeth 8
No- load
characteristics Voltage
11.5 V
Ampere 90A, MAX
Speed 2,600 rpm, MIN
CHARGING SYSTEM Items Specification
Alternator Type
Battery voltage sensing
Rate voltage 13.5 V, 110A
Speed in use 1,000 ~ 18,000 rpm
Voltage regulator Electronic built- in type
Regulator setting voltage 14.2 ~ 14.8V
Battery Type
MF 68AH
Cold cranking amperage [at - 18°C(- 0.4°F)] 600 A
Reserve capacity 110 min
Specific gravity [at 20°C(68°F)] 1.280 ± 0.01
a.COLD CRANKING AMPERAGE is the amperage a battery can deliver for 30 seconds and maintain a terminal
voltage of 7.2V or greater at a specified temperature.
b. RESERVE CAPACITY RATING is amount of time a battery can deliver 25A and maintain a minimum terminal
voltage of 10.5V at 26.7°C(80.1°F).
Page 218 of 1575
1.The above figure shows the relative operation structures of the housing vane to the rotor vane.
2. If the CVVT is held a certain control angle, to hold this state, oil is replenished as much as oil leaks from the oil
pump.
The OCV (Oil - flow Control Valve) spool location at this time is as follows.
Oil pump → Advance oil chamber (Little by little open the inflow side to the advance oil chamber) → Almost close the
drain side
Be sure there might be a difference in the position according to the engine running state (rpm, oil temperature, and oil
pressure).
Page 235 of 1575
J SpecificationItem Specification
Capacitance (pF) 950 ~ 1,350pF
CVVT OIL TEMPERATURE SENSOR (OTS)
J Type: Thermistor type
J Specification Temperature Resistance (kΩ)
°C °F
- 40 - 4052.0
- 20 -416.5
0 32 6.0
20 682.45
40 104 1.10
60 1400.544
80 1760.290
100 2120.164
120 2480.099
ACTUATORS
INJECTOR
J Number: 6
J Specification
Item Specification
Coil Resistance (Ω) 13.8 ~ 15.2 [20°C (68°F)]
PURGE CONTROL SOLENOID VALVE (PCSV)
J Specification Item Specification
Coil Resistance (Ω) 14.0 ~ 18.0 [20°C (68°F)]
VARIABLE INTAKE SOLENOID (VIS) VALVE #1 (SURGE TANK SIDE)
J Specification Item Specification
Coil Resistance (Ω) 29.0 ~ 35.0 [22°C (71.6°F)]
VARIABLE INTAKE SOLENOID (VIS) VALVE #2 (INTAKE MANIFOLD SIDE)
J Specification Item Specification
Coil Resistance (Ω) 29.0 ~ 35.0 [20°C (68°F)]
CVVT OIL CONTROL VALVE (OCV) [BANK 1]
J Specification Item Specification
Page 236 of 1575
Coil Resistance (Ω)6.7 ~ 7.7 [20°C (68°F)]
CVVT OIL CONTROL VALVE (OCV) [BANK 2]
J Specification Item Specification
Coil Resistance (Ω) 6.7 ~ 7.7 [20°C (68°F)]
ETC MOTOR
J Specification Item Specification
Coil Resistance (Ω) 1.275 ~ 1.725 [20°C (68°F)]
IGNITION COIL
J Type: Stick type
J Specification Item Specification
1st Coil Resistance (Ω) 0.62Ω±10Ë [20°C (68°F)]
2nd Coil Resistance (kΩ) 7.0kΩ±15Ë [20°C (68°F)]
SERVICE STANDARD
Ignition Timing BTDC 7°± 10°
Idle Speed A/CON OFF
Neutral,N,P - range
650 ± 100 rpm
D- range 650 ± 100 rpm
A/CON ON Neutral,N,P - range
650 ± 100 rpm
D- range 650 ± 100 rpm
TIGHTENING TORQUES
ENGINE CONTROL SYSTEM
Item kgf·mN·mlbf·ft
PCM installation bolts (on bracket) 1.0 ~ 1.29.8 ~ 11.8 7.2 ~ 8.7
PCM bracket installation bolts/nuts (on air cleaner assembly) 1.0 ~ 1.29.8 ~ 11.8 7.2 ~ 8.7
Camshaft position sensor [Bank 1] installation bolt 0.7 ~ 1.06.9 ~ 9.85.1 ~ 7.2
Camshaft position sensor [Bank 2] installation bolt 0.7 ~ 1.06.9 ~ 9.85.1 ~ 7.2
Crankshaft position sensor installation bolt 0.7 ~ 1.06.9 ~ 9.85.1 ~ 7.2
CVVT Oil control valve [Bank 1] installation bolt 0.8 ~ 1.07.8 ~ 9.85.8 ~ 7.2
CVVT Oil control valve [Bank 2] installation bolt 0.8 ~ 1.07.8 ~ 9.85.8 ~ 7.2
CVVT Oil temperature sensor installation 2.0 ~ 4.019.6 ~ 39.2 14.5 ~ 28.9
Engine coolant temperature sensor installation 2.0 ~ 4.019.6 ~ 39.2 14.5 ~ 28.9
ETC module installation bolt 0.9 ~ 1.18.8 ~ 10.8 6.5 ~ 8.0
Heated oxygen sensor (Bank 1 / Sensor 1) installation 3.5 ~ 4.534.3 ~ 44.1 25.3 ~ 32.6
Heated oxygen sensor (Bank 1 / Sensor 2) installation 3.5 ~ 4.534.3 ~ 44.1 25.3 ~ 32.6
Heated oxygen sensor (Bank 2 / Sensor 1) installation 3.5 ~ 4.534.3 ~ 44.1 25.3 ~ 32.6
Page 244 of 1575
13. Knock Sensor (KS) [Bank 1]
14. Knock Sensor (KS) [Bank 2]15. Injector
26. Ignition Coil
16. Accelerator Position Sensor (APS)18. CVVT Oil Control Valve (OCV) [Bank 1]
19. CVVT Oil Control Valve (OCV) [Bank 2]
20. CVVT Oil Temperature Sensor (OTS)
21. Purge Control Solenoid Valve (PCSV)
22. Variable Intake Solenoid (VIS) #1 Valve (Surge Tank
Side)
Page 255 of 1575
67Variable Intake Solenoid Valve #2 control output
Manifold Side]
68 Throttle Position Sensor signal (PWM) output ABS/ESP Control Module
69 Cruise "MAIN" lamp control output Cruise "MAIN" Lamp
70 Fuel Pump Relay control output Fuel Pump Relay
71 Variable Intake Solenoid Valve #1 control output Variable Intake Solenoid (VIS) Valve #1 Surge
Tank Side]
72 Immobilizer lamp control output Immobilizer Lamp
73 -y
74 -y
75 -y
76 -y
77 -y
78 Purge Control Solenoid Valve control output Purge Control Solenoid Valve (PCSV)
79 Wheel Speed Sensor [Low] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
80 Wheel Speed Sensor [High] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
CONNECTOR [C151- 2] Pin
No. Description
Connected to
1 ETC Motor [- ] control output ETC Motor (in ETC Module)
2 ETC Motor [+] control output ETC Motor (in ETC Module)
3 -y
4 CVVT Oil Temperature Sensor signal input CVVT Oil Temperature Sensor (OTS)
5 -y
6 -y
7 Engine Coolant Temperature Sensor signal input Engine Coolant Temperature Sensor (ECTS)
8 Manifold Absolute Pressure Sensor signal input Manifold Absolute Pressure Sensor (MAPS)
9 -y
10 -y
11 Reference voltage (+5V) Manifold Absolute Pressure Sensor (MAPS)
12 Battery voltage supply after ignition switch Ignition Switch
13 Reference voltage (+5V) Throttle Position Sensor (TPS) #2
14 Sensor ground Throttle Position Sensor (TPS) #1
15 Reference voltage (+5V) Camshaft Position Sensor (CMPS) [Bank 2]
16 Reference voltage (+5V) Throttle Position Sensor (TPS) #1
17 Sensor ground Camshaft Position Sensor (CMPS) [Bank 2]
18 Sensor ground Camshaft Position Sensor (CMPS) [Bank 1]
19 Ignition Coil (Cylinder #6) control output Ignition Coil (Cylinder #6)
20 -y
21 Crankshaft Position Sensor [High] signal input Crankshaft Position Sensor (CKPS)
22 -y
Knock Sensor (KS) [Bank 1], Knock Sensor (KS)
Page 256 of 1575
23Sensor Shield Knock Sensor (KS) [Bank 1], Knock Sensor (KS)
[Bank 2]
24 Camshaft Position Sensor [Bank 2] signal input Camshaft Position Sensor (CMPS) [Bank 2]
25 Camshaft Position Sensor [Bank 1] signal input Camshaft Position Sensor (CMPS) [Bank 1]
26 -y
27 -y
28 Sensor ground HO2S [B2 / S1] [Except for LEADED]
29 Sensor ground HO2S [B2 / S2] [Euro -Ⅲ/Ⅳ]
30 Sensor ground HO2S [B1 / S1] [Except for LEADED]
31 Sensor ground HO2S [B1 / S2] [Euro -Ⅲ/Ⅳ]
32 Reference voltage (+5V) Camshaft Position Sensor (CMPS) [Bank 1]
33 Sensor ground Engine Coolant Temperature Sensor (ECTS)
34 Sensor ground Manifold Absolute Pressure Sensor (MAPS),
CVVT Oil Temperature Sensor (OTS)
35 Power ground Chassis Ground
36 Power ground Chassis Ground
37 Power ground Chassis Ground
38 Power ground Chassis Ground
39 Power ground Chassis Ground
40 Ignition Coil (Cylinder #4) control output Ignition Coil (Cylinder #4)
41 Crankshaft Position Sensor [Low] signal input Crankshaft Position Sensor (CKPS)
42 -y
43 -y
44 -y
45 -y
46 -y
47 -y
48 Throttle Position Sensor #1 signal input Throttle Position Sensor (TPS) #1
49 Heated Oxygen Sensor [Bank 1 / Sensor 1] signal
input HO2S (B1/S1) [Except for LEADED]
50 Heated Oxygen Sensor [Bank 1 / Sensor 2] signal
input HO2S (B1/S2) [Euro -
Ⅲ/Ⅳ]
51 Heated Oxygen Sensor [Bank 2 / Sensor 1] signal
input HO2S (B2/S1) [Except for LEADED]
52 Heated Oxygen Sensor [Bank 2 / Sensor 2] signal
input HO2S (B2/S2) [Euro -
Ⅲ/Ⅳ]
53 Knock Sensor (KS) [Bank 2] [High] signal input Knock Sensor (KS) [Bank 2]
54 Knock Sensor (KS) [Bank 2] [Low] signal input Knock Sensor (KS) [Bank 2]
55 Knock Sensor (KS) [Bank 1] [Low] signal input Knock Sensor (KS) [Bank 1]
56 Knock Sensor (KS) [Bank 1] [High] signal input Knock Sensor (KS) [Bank 1]
57 Throttle Position Sensor #2 signal input Throttle Position Sensor (TPS) #2
58 Sensor ground Throttle Position Sensor (TPS) #2
59 -y
60 Ignition Coil (Cylinder #2) control output Ignition Coil (Cylinder #2)
Page 260 of 1575
64A/C Compressor Relay control
output A/C OFF
DCBattery Voltage
13.97V
A/C ON Max. 1.0V175mV
65 Cooling Fan [Low] control output Fan OFF
DCBattery Voltage
13.77V
Fan ON Max. 1.0V175mV
66 Cooling Fan [High] control output Fan OFF
DCBattery Voltage
13.57V
Fan ON Max. 1.0V- 25mV
67 Variable Intake Solenoid Valve
#2 control output Active
DCMax. 1.0 V
13.77
Inactive Battery Voltage- 25mV
68 Throttle Position Sensor signal
(PWM) output
Idle
PulseHi: Battery Voltage
13.37V
Lo: 0 ~ 0.5 V - 25mV
69 Cruise "MAIN" lamp control
output Cruise OFF
DCBattery Voltage
12.37V
Cruise ON Max. 1.0V- 25mV
70 Fuel Pump Relay control output Relay OFF
DCBattery Voltage
12.57V
Relay ON Max. 1.0V- 25mV
71 Variable Intake Solenoid Valve
#1 control output Active
DCMax. 1.0 V
175mV
Inactive Battery Voltage13.77V
72 Immobilizer lamp control output Lamp OFF
DCBattery Voltage
12.77V
Lamp ON Max. 1.0V- 25mV
73 - yy y y
74 - yy y y
75 - yy y y
76 - yy y y
77 - yy y y
78 Purge Control Solenoid Valve
control output Inactive
PulseHi: Battery Voltage
13.83V
Active Lo: Max. 1.0V31.54mV
79 Wheel Speed Sensor [Low]
signal input y
y y y
80 Wheel Speed Sensor [High]
signal input y
y y y
CONNECTOR [C151- 2] Pin
No. Description
ConditionType LevelTest Result
1 ETC Motor [- ] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 125mV
2 ETC Motor [+] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 325mV
3 - yy y y
4 CVVT Oil Temperature Sensor
signal input Idle
Analog 0 ~ 5.0V 282mV at 96°C
5 - yy y y
6 - yy y y
7 Engine Coolant Temperature
Sensor signal input Idle
Analog 0 ~ 5.0V 1.88V
Page 285 of 1575
CVVT Oil Temperature Sensor(OTS)
Page 286 of 1575
2007 > 2.7L V6 GASOLINE >
INSPECTION
FUNCTION AND OPERATION PRICIPLE
The CVVT Oil Temperature Sensor (OTS) is a negative coefficient thermistor used by the PCM tl measure engine oil
temperature for the purpose of adjusting CVVT calculations.
SPECIFICATION
Temperature Resistance (kΩ)
°C °F
- 40 - 4052.0
- 20 -416.5
0 32 6.0
20 682.45
40 104 1.10
60 1400.544
80 1760.290
100 2120.164
120 2480.099
CIRCUIT DIAGRAM