facia KIA CARNIVAL 2007 Workshop Manual

30.Install the engine cover. (see 'EM' group)
When replacing the automatic transaxle, reset the automatic transaxle's values by using the High- Scan Pro.
a. Connect the Hi - Scan Pro connector to the data link connector under the crash pad and power cable to the cigar
jack under the center facia.
b. Turn the ignition switch on and power on the Hi - Scan Pro.
c. Select the vehicle's name.
d. Select 'AUTOMATIC TRANSAXLE'.
e.Select 'RESETTING AUTO T/A VALUES' and perform the procedure.
f.Perform the procedure by pressing F1 (REST).

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
1.In- car air temperature sensor is located at the center facia lower panel.
2. The sensor contains a thermistor which measures the temperature of the inside. The signal decided by the
resistance value which changes in accordance with perceived inside temperature, is delivered to heater control unit
and according to this signal the control unit regulates incar temperature to intended value.
3. It perceives the inside temperature, changes the resistance value, and enters the corresponding voltage into the
automatic temperature control module.
4. It will used for discharge temperature control, sensor failsafe, temperature door control, blower motor level control,
and A/C auto control.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Ignition "ON"
2. Using the scan tool.
3. Check the frequency of humidity sensor between terminals 2 and 3.
Humidity (%) Frequency between terminals 2and 3 (Hz)
30 6976 ± 5%
50 6728 ± 5%
60 6600 ± 5%
70 6468 ± 5%
80 6330 ± 5%
90 6186 ± 5%
4. If the measured resistance is not specification, substitute with a known- good humidity sensor and check for proper
operation.
5. If the problem is corrected, replace the Humidity sensor.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center facia lower panel (A). (Refer to BD group)
3. Disconnect the humidity sensor connector (A).
4. Loosen 2 screws and then remove the humidity sensor (B).
5.Installation is the reverse order of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
CLUSTER FACIA PANEL REPLACEMENT
a. When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Tilt the steering column down.
2. Remove the screws, and detach the clips.
3. After disconnecting the connector (A), remove the cluster facia panel (B).
4.Installation is the reverse of removal.
a.Make sure the connector is plugged in properly.
CENTER FACIA PANEL REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Detach the clips, then remove the center facia panel (A).

[RHD]
5.Disconnect the connector (A).
6.Installation is the reverse of removal.
HEATER CONTROL UNIT REPLACEMENT
1.Remove the center facia panel.
2. Remove the console upper cover (A).
3. Disconnect the connector (B).
[LHD]

a.Make sure the connector(A) is plugged in properly.
CLUSTER REPLACEMENT
1.Remove the cluster facia panel.
2. Loosen the screws.
3.Disconnect the cluster connectors (A), then remove the cluster (B).

4.Installation is the reverse of removal.
a.Make sure the connector are plugged in properly.
AUDIO ASSEMBLY REPLACEMENT
1.Remove the center facia panel.
2. Loosen the screws.
3.Disconnect the connector (A), then remove the audio assembly (B).
4.Installation is the reverse of removal.
a.Make sure the connector are plugged in properly.

9.Installation is the reverse of removal.
CRASH PAD REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap itwith protective tape, and apply protective tapearound the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Remove the following items.
a. Front seat.
b. Cluster facia panel, cluster.
c. Audio assembly.
d. Glove box.
e. Side cover, center under cover.
f. Front pillar trim.
2. Remove the photo sensor (C), speaker connector (B).
3. Disconnect the passenger`s air bag connector (A).
Loosen the bolt and nut, then remove the crash pad (D).
4. Installation is the reverse of removal.
a.Make sure the crash pad fits onto the guide pins correctly.
b. Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
c. Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
d. Enter the anti- theft code for the radio, then enter.
[LHD]

2007 > 2.7L V6 GASOLINE >
INSPECTION
TAPE HEAD AND CAPSTAN CLEANING
1. To obtain optimum performance, clean the head, and capstan as often as necessary, depending on frequency of
use and tape cleanness.
2. To clean the tape head and capstan, use a cotton swab dipped in ordinary rubbing alcohol. Wipe the head and
capstan.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center facia panel, console lower cover, center air vent, switches, tray and heater control panel (A).
(Refer to the Body group - Crash pad)
3.Remove the mounting 4 screws then remove the audio unit (A).
4.Installation is the reverse of removal.
VIDEO JACK (DVD ONLY)
1.Disconnect the negative ( - ) battery terminal.

2.Installation is the reverse of removal.
WOOFER SPEAKER
1.Remove the rear seats. (Refer to the Body group - rear seats)
2. Remove the luggage side trim (Refer to the Body group - interior trim)
3. Remove the woofer speaker (A) after removing 4 bolts.
4.Installation is the reverse of removal.
EXTERNAL AMPLIFIER
1.Remove the driver seat. (Refer to the Body group - front seats)
2. Remove the external amplifier (A) after removing 3 bolts.
3.Installation is the reverse of removal.
FRONT CENTER SPEAKER
1.Remove the center facia panel.(Refer to the Body group - crash pad)