ECO mode KIA SELTOS 2023 Features and Functions Guide
Page 19 of 62
17†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
(Type A; but tons located on right side of Steering Wheel)
E CRUISE button: Press to turn the Cruise Control ON/OFF
F Res+ button: Press up to resume or increase cruising speed
Set- button: Press down to set or decrease cruising speed
CNCL button: To cancel Cruise Control, do one of the following:
•Press the brake pedal
•Press the CNCL button
G
Switch Modes*: To switch between standard Cruise Control and Smart Cruise Control, press and hold for more than two seconds
Cruise Control (CC)†1 8
RES
SET
CNCL+
–
CRUISE
OK
RESSET
CNCL+
–
CRUISE
OKRESSET
CNCL+
–
CRUISE
OK
RESSET+
–
CRUISE CRUISE CRUISE
OK
RES
SET+
–
CRUISE
OKRESSET+
–
CRUISEMODE
OK
RESSET+
–OKRESSET+
–OK
MODE
•Cruise Control is designed to function at above approximately 20 mph
•The Cruise Control system will not activate until the brake pedal has been depressed at least once after ignition ON or engine star ting
QUICK TIPS
REMINDER: Standard Cruise Control is a par t of Smar t Cruise Control (SCC)* and can be set as the operating mode To switch from SCC to Standard Cruise Control, press and hold the CRUISE but ton (the SCC system must not be activated to change modes) Repeat to switch back to SCC mode
E
F
G
Refer to section 5 in the Owner ’s Manual for more information
ADAS
Smart Cruise Control (SCC)*†5 (continued)
•If your vehicle speed is bet ween 5~20 mph when you press the Driving Assist CRUISE but ton, the Smar t Cruise Control speed will be set to 20 mph
•When following a vehicle, the system will automatically adjust your cruise speed based on the vehicle detected ahead If the vehicle detected remains at a standstill for more than 3 seconds, the system will disable
QUICK TIPS
REMINDERS:
•
Cruise Control but ton must be ON in order to turn SCC ON/OFF
•SCC can operate when the vehicle is driving faster than 6 mph
•
SCC is activated when ignition is turned on Speed will need to be reset when ignition is cycled on
•
SCC is turned ON again when the ignition is cycled off, then on again The speed set ting will need to be reset when ignition is cycled
•
SCC is also canceled when the driver ’s door is opened, gear shift is changed out of D (Drive), EPB is activated and various other conditions See Owner ’s Manual for other conditions
•
In standard Cruise Control, the driver needs to manually assess the distance from other vehicles as the system will not automatically apply brakes
•
If SCC is left on, it can be activated inadver tently Keep the system off when not in use to avoid set ting a speed that the driver is not aware of
•
When following a vehicle, the system will automatically adjust your cruise speed based on the vehicle detected in front
MY23 Seltos FFG Inside March 2022.indd 17MY23 Seltos FFG Inside March 2022.indd 174/15/22 3:39 AM4/15/22 3:39 AM
Page 20 of 62
18†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDS E LT O S FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
RESSET
CNCL+
–
CRUISE
OK
RESSET
CNCL+
–
CRUISE
OKRESSET
CNCL+
–
CRUISE
OK
RESSET+
–
CRUISE
OK
RESSET+
–
CRUISE
OKRESSET+
–
CRUISE MODE
OK
RES
SET+
–OKRESSET+
–
CRUISE
OK
MODE
RESSET+
–
CRUISE
OK
CRUISE
(Controls on right side of Steering Wheel if LFA /SCC equipped)
Lane Following Assist (LFA)*†5
Lane Following Assist (LFA) is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead, vehicles on the road, and potentially providing steering inputs The instrument cluster indicator will initially illuminate gray when turned ON, and on some vehicles, when SCC is engaged It will remain gray when the system does not detect the lane markers When the system detects the lane markers and can assist the steering, the LFA icon will illuminate green B
Hands-off Warning - If the driver takes their hands off the Steering Wheel for several seconds, a warning message will appear on the Instrument Cluster, and an audible warning will sound If hands on the Steering Wheel is not detected, LFA will cancel
When enabled, press the Driving Assist / LFA button C briefly to activate LFA
LFA Settings:
•LFA can be enabled by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User Settings* in the Instrument Cluster - Press the Mode button D on the Steering Wheel to toggle to User Settings Press the OK E up/down to toggle to Driver Assistance, select Lane Following Assist and press the OK button E
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select Driver Assistance, then Lane Following Assist and press the OK button E
•LFA Warning Timing – When in the Driver Assistance menu, select Warning Timing and one of the following:
- Normal: Maximizes the amount of distance between the vehicles before the initial
warning occurs
- Later: Reduces the amount of distance between the vehicles before the initial warning occurs
•LFA will operate only when these conditions are met:
- LFA recognizes both sides of the lane markers the vehicle is traveling in
- The vehicle is traveling slower than 120 mph
Images are for illustrative purposes only and may not reflect actual feature or operation
LFA is a supplemental system Do not solely rely on this system and always pay at tention to the road and its conditions
When engaged, LFA is not a substitute for safe and proper driving Always drive safely and use caution
Actual User Set tings steps may var y by model See section 5 in the Owner ’s Manual for more detailed information, limitations and conditions
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
REMINDER: If the ignition is cycled, LFA returns to its previous state, on or off, if activated in the User Set tings menu and when combined with SCC If using the Steering Wheel LFA but ton, then LFA defaults to off
A
B
C
E
ADAS
D
MY23 Seltos FFG Inside March 2022.indd 18MY23 Seltos FFG Inside March 2022.indd 184/15/22 3:39 AM4/15/22 3:39 AM
Page 21 of 62
19ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
When engaged, Highway Driving Assist is not a substitute for safe driving, may not detect all objects around the vehicle, and only functions on cer tain federal highways
Always drive safely and use caution See section 5 in the Owner ’s Manual for more detailed information, limitations and conditions Images are for illustrative purposes only and may not reflect actual feature or operation
Highway Driving Assist (HDA)*†5
Highway Driving Assist (HDA) is designed to adjust the set speed of the vehicle and the distance with the vehicle ahead, when driving on limited/controlled access highways/freeways HDA can adjust the vehicle’s speed based on available highway speed information The automatic speed setting mode is designed to adjust the Smart Cruise Control (SCC) set speed automatically by adjusting to the current speed limits of the highway the vehicle is traveling on
When HDA is activated, the conditions are met, the Instrument Cluster indicator will illuminate green A If proper conditions are not met, HDA will be in standby mode and the indicator will illuminate gray When HDA is operating, and if both lanes are recognized, the Instrument LCD image will show the lanes illuminated white B and the HDA indicator A illuminated green
If HDA is activated and operating, conditions are met and the Smart Cruise Control (SCC) speed is set by the driver (at the posted highway speed limit or slower), HDA will enter the automatic speed setting mode The set speed and AUTO will be displayed C in green and an audible alert will sound
Hands-off Warning - If the driver takes their hands off the Steering Wheel for several seconds, a warning message will appear on the Instrument Cluster, and an audible warning will sound If hands on the Steering Wheel is not detected, HDA will cancel
HDA will operate only when these conditions are met:
•The vehicle is traveling slower than 95 mph
•When driving on limited/controlled access highways/freeways
•When the SCC is on and operating
•When the SCC speed is set to current limited/controlled access highways/freeways speed
HDA settings:
•HDA can be turned on/off by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User Settings* in the Instrument Cluster - Press the Mode button B on the Steering Wheel to toggle to User Settings Press the OK C up/down to toggle to Driver Assistance, then Driving Assist Select Highway Driving Assist and press the OK button C
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select Driver Assistance, then Driver Convenience Select Highway Driving Assist to activate
RES
SET
CNCL+
–
CRUISE
OK
RESSET
CNCL+
–
CRUISE
OKRESSET
CNCL+
–
CRUISE
OK
RESSET+
–
CRUISECRUISE CRUISE
OK
RES
SET+
–
CRUISE
OKRESSET+
–
CRUISE MODE
OK
RES
SET+
–OKRESSET+
–OK
MODE
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Highway Driving Assist (HDA) Video
QR CODE
REMINDERS:
•
If the driver changes the speed while in automatic speed set ting mode, it deactivates and enters a manual mode
•
When the ignition is cycled, HDA returns to its previous state
E
D
A
mph
60mph
B
C
ADAS
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED
MY23 Seltos FFG Inside March 2022.indd 19MY23 Seltos FFG Inside March 2022.indd 194/15/22 3:39 AM4/15/22 3:39 AM
Page 22 of 62
20†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDS E LT O S FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
(Rear View Camera)
(Rear View Camera Display)P
R
N
DSHIFTL OCK
RELEASE
Rear View Monitor (RVM)†5
Rear View Monitor is a supplemental system that displays the view behind the vehicle through the infotainment system screen while the vehicle is in R (Reverse)
Rear View Monitor activates when the:
1 Engine Start/Stop* button is in the ON (Red light) position
2
Gear Shift Lever is in the R (Reverse) position
When engaged, Rear View Monitor is not a substitute for proper and safe backing-up procedures Always drive safely and use caution when backing up The Rear View Monitor may not display ever y object behind the vehicle
The screen image above is for illustrative purposes only The actual image or graphics may differ in your vehicle
Refer to section 4 in the Owner ’s Manual for more information
REMINDERS:
•
Through normal use and after inclement weather or washing, the rear camera may become dir t y Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•While Rear View Monitor is active the volume will be lowered on all audio modes
ADAS
MY23 Seltos FFG Inside March 2022.indd 20MY23 Seltos FFG Inside March 2022.indd 204/15/22 3:39 AM4/15/22 3:39 AM
Page 28 of 62
26 *IF EQUIPPEDS E LT O S FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you The High Beam Assist indicator will illuminate
Headlight ON position
Parking light position
AUTOAuto Light / DRL / HBA
OFFLights OFF
AUTO
OF F
OFF
Refer to section 4 in the Owner ’s Manual for more information
Refer to section 4 in the Owner ’s Manual for more information
Headlights & High BeamsHigh Beam Assist (HBA)
To operate:
•Rotate lever switch to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights / High Beams
AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically, depending on the amount of light outside the vehicle Turn Signals & Fog Lights*
To operate:
•Turn Signals - Move lever Up/Down for Right/Left Turn Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF
One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever up/down slightly for less than 1 second and then releasing The lane change signal will blink 3 times
To change how many times (3/5/7) the Lane Change Signal blinks, go to User Settings Mode* in the LCD Instrument Cluster modes
For illustrative purposes only Your actual display, but tons and/or features may var y
See section 4 in the Owner ’s Manual for more information
Daytime Running Lights (DRL)*
DRL may help others to see the front of your vehicle during the day The lights will be on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch
is in the AUTO position, unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Fog lights are on
•Engine is turned off
•Switch is in the OFF position
REMINDERS:
•
HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and the low beams will be on continuously
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
"