instrument cluster KIA SORENTO PHEV 2023 Features and Functions Guide

13 *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
A
REMINDERS:
•When indicator is blinking red, there’s an error while tr ying to charge
•
When the charging connector is connected and the reser ved charging is in standby mode, the charging indicator is turned off and the scheduled charge release but ton indicator is turned on The scheduled charge release but ton indicator will turn off after 3 minutes
•
For more detail and/or subsequent steps in charging your vehicle, please see section 1 of the Owner ’s Manual
OFF
OFF
OFF
OFF
HYBRID / PLUG-IN HYBRID SYSTEM
(Located on rear passenger side of vehicle)
G
J
H
I
(Message on Cluster Display)
Remaining Time
99
kW
9 h 13 m30%
K
Charging the Plug-In Hybrid Vehicle (Continued)
To charge the Plug-In Hybrid vehicle using a Level 1 or 2 charger:
1 Connect the ICCB plug A to an electrical outlet
2 Check if the power light (green) B on the ICCB turns on
3 Press the brake pedal and engage the parking brake
4 Turn off all switches, put the shift lever in P (Park), and turn off the vehicle
5 Open the charging door G by pressing the rear center edge of charging door (Ensure doors are unlocked)
6 Remove any dust or water on the charging connector and charging inlet H
7 Hold the charging connector handle I and connect it to the vehicle’s charging inlet H by pushing the connector until you hear a clicking sound
8 Charging begins automatically (Ensure the charge indicator light is illuminated on your instrument cluster, indicating the vehicle is charging)
Checking the Charging Status
The charging status can be checked by viewing the charging status indicator J near the charging inlet (bottom indicator) The charging indicator will blink yellow when charging, and the charge is from 0-65% The charging indicator will blink green when charging and the charge is from 65-100% The indicator will turn off within 5 seconds when charging is completed
The remaining charging time will be displayed in the Instrument Cluster K for one minute, or when a driver ’s door is opened during charging
Removing the Charging Connector
To prevent charging cable theft, the charging connector cannot be disconnected from the inlet when the doors are locked or the charging connector is in the LOCK mode Unlock all doors to disconnect the charging connector from the inlet If the release button does not work even after the all doors are unlocked, pull the emergency lift cable in the engine room
HYBRID/PLUG-IN

HYBRID
POWER
CHARGE
FA U LT!
LEVELLMH
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Plug-In Hybrid Charging Video
QR CODE
B

14 *IF EQUIPPEDSORENTO HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
HYBRID / PLUG-IN HYBRID SYSTEM
HYBRID/PLUG-IN

HYBRID
Hybrid/Plug-In’s instrument cluster LCD screen displays the following Hybrid/Plug-In system modes to inform the driver of its status To change modes, go to User Settings in the Instrument Cluster modes
Energy Flow - Instrument Cluster LCD
Your vehicle’s instrument cluster display locations may differ from those in the illustrations For more information on the instrument cluster, please refer to section 1 of the Owner ’s Manual
These illustrations are for demonstration purposes only
&OFSHZ
'MPX
&OFSHZ
'MPX
&OFSHZ
'MPX
&OFSHZ
'MPX
EV Propulsion - The electric motor is moving the vehicle Engine-Only Propulsion - The engine is moving the vehicle
Power Assist - Both the electric motor AND the engine are moving the vehicle Engine Generation - While the vehicle is stopped, the engine is charging the Hybrid/Plug-In battery
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Plug-In Hybrid Instrument Cluster Overview Video
QR CODE

15 *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
Optima Hybrid/Plug-In’s instrument cluster LCD screen displays the following Hybrid/Plug-In system modes to inform the driver of its status To change modes, go to User Settings in the LCD Instrument Cluster modes
Power Reserve - While the engine powers the vehicle, it is also recharging the Hybrid/Plug-In battery Engine Brake/Regeneration - The regenerative braking system is recharging the Hybrid/Plug-In battery
Vehicle Stop - The vehicle’s Hybrid/Plug-In system is standing by Engine Generation/Regeneration - The engine and the regenerative braking system are both recharging the Hybrid/Plug-In battery
&OFSHZ
'MPX
&OFSHZ
'MPX
&OFSHZ
'MPX
&OFSHZ
'MPX
Energy Flow - Instrument Cluster LCD (continued)
Your vehicle’s instrument cluster & indicator light locations may differ from those in the illustrations For more information on the instrument cluster, please refer to section 1 of the Owner ’s Manual
Illustrations are for demonstration purposes only Some indicators and warning lights may not appear in illustration On the vehicle, they may appear in the LCD
HYBRID / PLUG-IN HYBRID SYSTEM
HYBRID/PLUG-IN

HYBRID
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Plug-In Hybrid Instrument Cluster Overview Video
QR CODE

17 *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
(Located on but ton panel below Gear Shift)*
DRIVE
SPORT
SMART
EV
HEV
ECO SNOW
TERRAIN
COMFORT
AHYBRID/PLUG-IN

HYBRID
For more information, refer to sections 1 and 5 of the Owner ’s Manual

To change the Plug-In Hybrid Mode, press the EV/HEV button A (PHEV only); switch between Automatic mode, Electric (EV) mode and Hybrid (HEV) mode each time the button is pressed
The LCD on the Instrument Cluster will display the mode selected:
•Automatic Mode - AUTO will be displayed on the instrument cluster and the vehicle will operate in Hybrid or Electric vehicle mode as needed
•Electric Mode - EV will display on the instrument cluster and the vehicle operates on the EV battery until the power is low, then it switches to HYBRID mode
•Hybrid mode - HEV will display on the instrument cluster and the high-voltage
Plug-In Hybrid Modes (Plug-In Hybrid only)
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Plug-In Hybrid Modes - Automatic, EV and HEV Video
QR CODE
HYBRID / PLUG-IN HYBRID SYSTEM

18†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSORENTO HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
OK
MODE
OK
MODEMODE
OKOK
OKOK
OKOK
OK
MODE
MODEMODE
MODEMODE
OK
MODE
MODEMODE
OK
MODEMODE
COLLISION WARNING
EMERGENCY BRAKING
Forward Collision-Avoidance Assist (FCA)†3
FCA is designed to detect and monitor a vehicle ahead or detect a pedestrian in the roadway through front view camera recognition and front radar signals to warn the driver that a collision is imminent, and if necessary, temporarily apply emergency braking Initially, FCA provides Collision Warning A when it detects a potential collision with a vehicle, pedestrian, or cyclist, emitting an audible warning and visual alert on the instrument cluster
If FCA detects that the collision risk has increased, FCA automatically applies the brakes to reduce your speed, potentially helping to reduce the effects of a possible collision B
With the turn signal on, if it detects a potential collision, Junction Turning E may help to avoid the collision with an oncoming vehicle in an adjacent lane when turning left by applying emergency braking
FCA Settings:
•FCA is on by default in most Kia models FCA can be turned on/off by going to the User Settings* in the
Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings Press the OK D up/down to toggle to Driver Assistance and select an FCA mode
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select DRIVER ASSISTANCE and select an FCA mode
•FCA Modes – Select one of the following:
–Active Assist: Vehicle will provide a warning (audible & visual) and apply the brakes if needed
–Warning Only: Vehicle will provide a warning only (audible & visual)
–Off: System is off, no warnings or braking provided
•Warning Timing – When in the DRIVER ASSISTANCE menu, select WARNING TIMING and one of the following:
–Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
–Later: Reduces the amount of distance between the vehicles before the initial warning occurs
FCA will become active when the:
•Ignition is on or the Engine Start/Stop button* is ON
•Vehicle is traveling faster than 6 mph
•Electronic Stability Control (ESC) is ON
When engaged, For ward Collision-Avoidance Assist (FCA) is not a substitute for safe driving and may not detect all objects in front of the vehicle or aler t the driver when the vehicle is approaching another vehicle Always drive safely and use caution
REMINDERS:
•
FCA will be activated by default when the ignition is cycled ON, even when previous set ting was OFF
•
If FCA is operating and the ESC (Electronic Stabilit y Control) is turned off, FCA is automatically turned off
•
When FCA is off, the For ward Safet y warning indicator is on in the Instrument Cluster
A
B

The Warning Volume can be adjusted in the User Set tings in the Instrument Cluster (Go to Driver Assistance, then Warning Volume) or the Vehicle Set tings* on the Infotainment System Go to Driver Assistance* Warning Method, then Warning Volume
QUICK TIP
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Forward Collision- Avoidance Assist (FCA)Video
QR CODE
C
D
Actual User Set tings steps may var y by model For illustrative purposes only Your actual display, but tons and/or features may var y Refer to section 6 in the Owner’s Manual for more information
(Junction Turning)
E
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS

19†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
ADAS
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Blind-spot Collision-Avoidance Assist Video
QR CODE
OK
MODE
OK
MODEMODE
OKOK
OKOK
OKOK
OK
MODE
MODEMODE
MODEMODE
OK
MODE
MODEMODE
OK
MODEMODEC
D
Blind-spot Collision-Avoidance Assist (BCA)†3
BCA uses rear corner radar sensors in the rear bumper to monitor and warn the driver in certain situations if it detects an approaching vehicle in the driver ’s blind spot area and before changing lanes Initially, BCA provides a Collision Warning when it detects a potential collision with a vehicle, emitting an audible warning and visual alert on the outside rearview mirrors If BCA detects that the collision risk has increased, BCA automatically applies the opposite side front brake to try and mitigate a potential collision
Vehicle detection: When another vehicle is detected within BCW warning boundary A, an indicator will illuminate on the outside rearview mirrors B
Collision warning: When vehicle detection warning is on and the driver activates a turn signal, a flashing indicator will illuminate on the outside rearview mirrors and BCA will sound a warning
Collision-Avoidance Assist: When collision warning has already occurred, and the collision risk has increased, braking is applied to the opposite side front wheel and a visual warning occurs When you are driving forward out of a parking space, if BCA determines that there is a collision risk with an approaching vehicle in the blind spot, BCA will help avoid a collision by applying the brake
BCA Settings:
•BCA can be turned on/off by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings Press the OK D up/down to toggle to DRIVER ASSISTANCE, then BLIND-SPOT SAFET Y and select a BCA mode
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select DRIVER ASSISTANCE, then BLIND-SPOT SAFET Y and select a BCA mode
•BCA Modes – Select one of the following:
- Active Assist: BCA will provide a warning (audible & visual) and may activate Electronic Stability Control (ESC) and temporarily apply braking power
- Warning Only: Vehicle will provide a warning only (audible & visual)
- Off: BCA is off, no warnings provided
•Warning Timing – When in the DRIVER ASSISTANCE menu, select WARNING TIMING and one of the following:
-
Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
- Late: Reduces the amount of distance between the vehicles before the initial warning occurs
REMINDERS:
•
When BCA is ON and the ignition is cycled, BCA returns to its previous state
•
BCA may sound when making a left turn Maintain a proper distance from oncoming vehicles
Refer to section 6 in the Owner ’s Manual for more information
•The Warning Volume can be adjusted in the User Set tings in the Instrument Cluster (Go to Driver Assistance, then Warning Volume) or the Vehicle Set tings* on the Infotainment System Go to Driver Assistance, Warning Method, then Warning Volume
•BCA will activate when: -BCA is turned on -
Other vehicles are detected on the rear sides of the vehicle -Collision Warning is above approximately 12 mph; Collision-Avoidance Assist is above approximately 40 mph
QUICK TIPS
A
B
When engaged, BCA is a supplemental system Do not solely rely on this system and always pay at tention to the road and its conditions
The images on this page are for illustrative purposes only and may not reflect actual feature or operation
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)

20†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSORENTO HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
HOLD
(Located on Driver ’s Panel to the left of the steering wheel)
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Lane Keeping Assist (LK A)Video
QR CODE
A

The Warning Volume can be adjusted in the User Set tings in the Instrument Cluster (Go to Driver Assistance, then Warning Volume) or the Vehicle Set tings* on the Infotainment System Go to Driver Assistance, Warning Method, then Warning Volume
QUICK TIP
EF
324mi
MPH
CHARGE
ECO
POWER
L H
D
E F
324mi
MPH
CHARGE
ECO
POWER
L H
D
E F
324mi
MPH
CHARGE
ECO
POWER
L H
D
E F
324mi
MPH
CHARGE
ECO
POWER
L H
D
When LK A detects the lane markers, both lanes are displayed white
When LK A does not detect the lane markers, the lanes are displayed gray
When LK A detects the vehicle moving outside of the lane being traveled in, a yellow indicator will illuminate either on the left or right lane (shown in both images above)
Lane Keeping Assist is not a substitute for safe driving and may not always aler t the driver if the vehicle is driven outside of its lane Always drive safely and use caution
Actual User Set tings steps may var y by model Refer to section 6 in the Owner ’s Manual for more information
For illustrative purposes only Your actual display, but tons and/or features may var y
Lane Keeping Assist (LKA)*†3
Lane Keeping Assist (LK A) is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to potentially help keep the vehicle in the lane When turned on, the instrument cluster indicator will initially illuminate white or green It will remain white when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers When LK A detects the lane markers and can assist the steering, the Lane Safety icon will illuminate green
If LK A detects that you are moving outside of your lane, LK A may give an audible warning and display Lane Departure Warning on the instrument cluster, or, LK A may provide steering inputs, trying to prevent the vehicle from moving outside its lane
Hands-off Warning - If the driver takes their hands off the Steering Wheel for several seconds, a warning message will appear on the Instrument Cluster
There are three available modes:
•Off - LK A will turn off
•
Lane Keeping Assist - LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•
Lane Departure Warning - LK A will warn the driver with an audible warning when lane departure is detected The driver must steer the vehicle
LK A will operate under the following conditions:
•The vehicle speed exceeds approximately 40 mph
•
LK A recognizes both sides of the lane markers the vehicle is traveling in
•
The vehicle is between the lane markers
REMINDERS:
•
LK A will not issue a warning if the turn signals or hazard lights are activated
•
When the ignition is cycled, LK A will return to the previously set state
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS

21ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS †LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPED
OK
MODE
OK
MODEMODE
OKOK
OKOK
OKOK
OK
MODE
MODEMODE
MODEMODE
OK
MODE
MODEMODE
OK
MODEMODE
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Intelligent Speed Limit Assist (ISLA) Video
QR CODE

You can set a speed limit offset to the posted speed limit by going to User Set tings, Driver Assistance, Speed Limit, then Speed Limit Offset Set the offset to “0” if you want the vehicle to travel at the detected speed limit, when ISL A is on
QUICK TIP
Intelligent Speed Limit Assist (ISLA)†3
Intelligent Speed Limit Assist is designed to use the information from the posted speed limit D and the navigation system to inform the driver of the speed limit
When ISL A is on and active, the system will display an alert on the Instrument Cluster LCD of the detected speed limit If the vehicle’s current speed exceeds the detected speed limit, the speed limit information will illuminate red on the LCD
ISLA User Settings:
To enable ISL A on, press the SETUP key/button on the Infotainment System Select the VEHICLE button to enter the Vehicle Settings Select DRIVER ASSISTANCE, then SPEED LIMIT
Select one of the three modes:
•Speed Limit Assist: Informs the driver of the detected speed limit, display a message change the set speed of the MSL A or SCC to help the driver stay within the posted speed limit In addition, ISL A will inform the driver to change set speed of Manual Speed Limit Assist or Smart Cruise Control to help the driver stay within the speed limit
•Speed Limit Warning: Informs the driver of the detected speed limit D and warn the driver when the vehicle is traveling faster than the posted speed limit
•Off: ISL A is disabled
REMINDERS:
•
Vehicle must be parked and in a safe location to change the speed set tings
•
Additional information may be displayed if additional road sign information is detected
LKA Settings:
•Press and hold the Lane Driving Assist button A to turn LK A on or off, when it is first enabled in the User Settings* in the Instrument Cluster or Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User settings* in the Instrument Cluster - Press the Mode button B on the Steering Wheel to toggle to User Settings Press the OK button C up/down
to toggle to DRIVER ASSISTANCE and then L ANE SAFET Y
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select DRIVER ASSISTANCE and then L ANE SAFET Y
REMINDERS:
•
Some models access set tings through the Vehicle Set tings in the audio head unit Press the Setup hard key on the infotainment system, then VEHICLE on the screen to enter Vehicle Set tings
Lane Keeping Assist (LKA)†3 (continued)
B
C
ADAS
0
7
8
6
１
60
20
１40
40
１20
60
１00
80
0 25 507560.1 MPG
ElectricRange
P
Gasoline
0
mi
393 mi
DA
Refer to section 6 in the Owner ’s Manual for more information

Refer to section 6 in the Owner ’s Manual for more information
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)

22†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSORENTO HYBRID / PLUG-IN HYBRID FEATURES & FUNCTIONS GUIDE
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Driver At tention Warning is not a substitute for safe driving and may not detect all instances of inat tentive driving practices Failure to pay at tention to travel conditions and vehicle operation could result in loss of vehicle control Always drive safely and use caution
See section 6 in the Owner ’s Manual for more information
Driver Attention Warning is designed to alert the driver if it detects inattentive driving practices and, in certain situations, can give a warning signal to take a break from driving If DAW is activated, the DAW information A will appear on the Instrument Cluster LCD when you select the Assist mode in the Instrument Cluster User Settings A message, “Consider taking a break,” B appears on the LCD and a warning sounds to suggest the driver take a break when the driver ’s attention level becomes low
DAW Settings:
•DAW can be turned on/off by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/ Stop button* in the on position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings Press the OK D up/down to toggle to DRIVER ASSISTANCE, then DRIVER ATTENTION WARNING and select INATTENTIVE DRIVING
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button Press VEHICLE to enter Vehicle Settings Select DRIVER ASSISTANCE, then DRIVER ATTENTION WARNING and select INATTENTIVE DRIVING
REMINDERS:
•
The setup of DAW will be maintained, as selected, when the ignition is cycled
•
When activated, DAW does not display “Consider taking a break ” message when the total trip driving time is less than 10 minutes
Driver Attention Warning (DAW)*†4
Consider taking a break
Attention Level
HighAB
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Driver Attention Warning (DAW) Video
QR CODE
OK
MODE
OK
MODEMODE
OKOK
OKOK
OKOK
OK
MODE
MODEMODE
MODEMODE
OK
MODE
MODEMODE
OK
MODEMODEC
D
ADAS

23†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
OK
MODE
OK
MODEMODE
OKOK
OKOK
OKOK
OK
MODE
MODEMODE
MODEMODE
OK
MODE
MODEMODE
OK
MODEMODE
Leading Vehicle Departure Alert is designed to inform the driver when the vehicle in front starts moving or departs from a stop When LVDA is on, your vehicle is stopped and detects that the leading vehicle is driving away, LVDA sounds an alert to let you know you can start driving If no action is taken after the vehicle in front drives away, then a message A will appear on the Instrument Cluster LCD
LVDA User Settings:
•
To turn LVDA on, press the Mode button B on the Steering Wheel, and go to User Settings in the Instrument Cluster Press the OK button C up/down and select DRIVER ASSISTANCE, then press the OK button C to select Go to DRIVER ATTENTION WARNING and then LEADING VEHICLE DEPARTURE ALERT
•Some models access settings through the Vehicle Settings in the infotainment system Press the SETUP hard key on the infotainment system, then press VEHICLE on the screen to enter Vehicle Settings
The Leading Vehicle Depar ture Aler t system is not a substitute for safe and proper driving Always drive safely and use caution
Images are for illustrative purposes only and may not reflect actual feature or operation
See section 6 in the Owner ’s Manual for more information
(But tons located on steering wheel)
Leading Vehicle Departure Alert (LVDA)†3
REMINDERS:
•
When the ignition is cycled, the system returns to its previous state, on or off
•
Always check the front of the vehicle and road conditions before depar ture
REMINDER: SEA may not detect all objects and the occupants should always be mindful of their surroundings
Refer to the inside front cover for more information on QR codes www youtube com/KiaFeatureVideos
Leading Vehicle Departure Alert (LVDA) Video
QR CODE
Leading vehicle
is driving away
A
B
C
Safe Exit Assist (SEA) Video
Safe Exit Assist (SEA)*†3
Safe Exit Assist (SEA) can help prevent passengers from opening their door by displaying a warning message on the Instrument Cluster and sounding an audible warning when a vehicle is detected, approaching from behind, and after your vehicle has stopped In addition, when the electronic child safety lock button is in the LOCK position and an approaching vehicle from the rear area is detected, the electronic child safety lock button will not unlock even if the driver presses the button to prevent the rear doors from opening
To turn on SEA , go to User Settings* in the Instrument cluster or the Vehicle Settings* in the infotainment system, select DRIVER ASSISTANCE, then BLIND-SPOT SAFET Y, and select SAFE EXIT WARNING, and ACTIVE ASSIST
See section 6 in the Owner ’s Manual for more information
Watch for traffic
5IF
8BSOJOH
7PMVNF
DBO
CF
BEKVTUFE
JO
UIF
6TFS
4FU UJOHT
JO
UIF
*OTUSVNFOU
$MVTUFS
(P
UP
%SJWFS
"TTJTUBODF

UIFO
8BSOJOH
7PMVNF

PS
UIF
7FIJDMF
4FU UJOHT
PO
UIF
JOGPUBJONFOU
TZTUFN
(P
UP
%SJWFS
"TTJTUBODF

8BSOJOH
.FUIPE

UIFO
8BSOJOH
7PMVNF 
QUICK TIP
ADAS