light KIA SPORTAGE 2018 Features and Functions Guide

STEERING WHEEL CONTROLS
14*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
Headlights & High Beams
AUTO Light* — When the light switch is in the AUTO Light
position, the tail lights and headlights will turn ON/OFF automatically,
depending on the amount of light outside the vehicle .
To o p e r a t e :
•Rotate lever to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights / High Beams
Adaptive Front Lighting System (AFLS)*
The Adaptive Front Lighting System helps improve visibility during
nighttime driving by aiming the low beam headlights in the direction the
vehicle is moving . AFLS controls the aiming direction based on steering
angle and speed .
When the light switch is in the AUTO Light position, the AFLS will activate .
REMINDER: When the AFLS indicator illuminates on the instrument cluster, the AFLS is not working properly . See authorized Kia dealer for service .
High Beam Assist (HBA)*
High Beam Assist automatically adjusts the headlight range by switching
between high and low beams based on light from other vehicles and road
conditions .
To enable HBA, toggle the light switch to the AUTO Light position and turn
on the high beams by pushing the lever away from you . The High Beam
Assist indicator will illuminate .
REMINDERS:
• HBA will operate when vehicle speed exceeds 25 mph
• If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
• If the light switch is switched to the headlight position, HBA will turn off low beams will be on continuously
Headlight position
Parking light position
AUTOAuto Light* / AFLS* / HBA*
DRLOFFDaytime Running Lights OFF
AUTO
OF F

STEERING WHEEL CONTROLS
*IF EQUIPPED 15ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
Turn Signals & Fog Lights*
To o p e r a t e :
•Turn Signals - Move lever Up/Down for Right /Left Turn Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for fog light operation .
One-Touch Lane Change Signal is activated by moving the Turn
Signal Lever up/down slightly for less than 1 second and then
releasing . The lane change signal will blink 3 times .
To change how many times (3/5/7) the Lane Change Signal blinks, go
to User Settings Mode in the LCD Instrument Cluster modes .
For more information on the User Settings Mode, please refer to your Owner’s Manual.
Sportage Daytime Running Lights Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
www.youtube.com/KiaFeatureVideos
QR CODE
.
Daytime Running
Lights (DRL)*
DRL may help others to see the front of
your vehicle during the day . The lights will
be on automatically when the ignition or
Engine Start /Stop button is ON and the
headlight switch is in the AUTO position,
unless one of the following occurs:
•Headlights are on
•Parking brake is applied
•Fog lights are on
•Engine is turned off
•Switch is in the OFF position
REMINDER: DRL only operates during the daytime .
A

AUDIO SYSTEMS
*IF EQUIPPED 21ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
For further UVO eServices System operations, refer to the Car Multimedia System User's Manual. For other audio system information, refer to pages 20-23.
UVO eServices / Android AutoTM / Apple CarPlay® Setup
UVO eServices Registration/Activation – To use UVO eServices:
1 . On your Smartphone, go to an app store or marketplace to download the free Kia UVO eServices app .
2 . Open the UVO eServices app and create an account by clicking on REGISTER . After entering your information and following the prompts to complete
registration, go to your email and click on the confirmation link ( You can also register an account by logging into MyUVO .com) .
3 . In the app, click CONTINUE, accept the terms and click CONTINUE once again .
4 . Follow the app’s IN-CAR SETUP instructions to connect your smartphone and complete UVO eServices activation .
Apple CarPlay®*
Setting up and starting Apple CarPlay®:
1 . Connect the Apple CarPlay® compatible iPhone with the vehicle’s
USB port using the manufacture’s cable provided with your iPhone .
2 . On the UVO eServices System audio control unit, press the
SETUP key .
3 . Press the CONNECTIVIT Y button on the screen and select Apple
CarPlay® .
4 . Select ENABLE APPLE CARPL AY .
5 . From the vehicle’s home screen, select the Apple CarPlay® button,
where you’ll see all the Apple CarPlay® supported apps
Android Auto™*
Setting up Android Auto™:
1 . From an Android Auto™ compatible device, download the Android Auto™
app from the Google Play™ Store .
2 . Open the Android Auto™ app and proceed with the on-screen
instructions to complete setup on the mobile device .
How to start Android Auto™:
1 . Press the SETUP key on your UVO eServices system’s control panel .
2 . Press the CONNECTIVIT Y button, select Android Auto™ then select
ENABLE ANDROID AUTO .
3 . Connect the Android™ device with the vehicle’s USB port using the
manufacturer’s cable provided with your phone .
4 . From the vehicle’s home screen, select the Android Auto™ button,
where you’ll see all the Android Auto™ supported apps .
REMINDERS:
•
Android Auto compatibility requirements: Micro-USB cable that came with your phone, OS Android™ 5 .0 or higher, compatible Android smartphone and data and wireless plan for applicable feature(s) .
•
Apple CarPlay compatibility requirements: Apple Lightning® cable, latest iOS software, iPhone 5 or later and data and wireless plan for applicable feature(s)

24*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
CENTER PANEL
Aux/USB/iPod® Port & Power OutletsDigital Clock
Standard Audio System*:
Press SETUP button on Audio system, then press on-screen instructions to
change clock settings .
UVO eServices System Clock Setup*:
Press the SETUP button, then press the on-screen Clock icon to enter
clock settings .
UVO eServices with Premium Navigation System Clock Setup*:
Press the SETUP button, then press the on-screen Clock icon to enter
clock settings .
Use the Aux port A to connect audio devices and the USB port to connect
USB audio devices, smartphones and iPod® devices .
B Use the power outlets for mobile phones and other devices designed to
operate on a 12V (180W max) power outlet .
The power outlets are inactive when ignition is in the OFF position .
QUICK TIP
• Press the RETURN button on the navigation screen to ensure changes are saved .
• When needed, Daylight Savings must be enabled in the Clock Settings screen
• To access manual date and time setting, turn GPS time OFF in the Clock Settings (UVO eServices with Premium Navigation System*)
QUICK TIP
REMINDER: Using the power outlets, USB/Aux ports for prolonged periods of time with the Engine Start /Stop button in the ACC position (Engine OFF ) could cause the battery to discharge .
For more information on the Aux/USB/iPod® Ports and Power Outlets, refer to the Owner's Manual.
(Located on back of center console)
(Located on center panel)
ABB
B

28*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
CENTER PANEL
(Type B shown . Located below gear shift)
Electronic Parking Brake (EPB)*
The Electronic Parking Brake (EPB) system utilizes an electric motor to
engage the parking brake .
Applying the Parking Brake
Depress the brake pedal and pull up the EPB switch A . Ensure that the
indicator light is illuminated on the instrument cluster .
If parked on a steep incline/decline, pull up the EPB switch for more than 3
seconds for a firmer EPB application .
Releasing the Parking Brake
The EPB will automatically release when the shifter is placed in Reverse or
Drive .
To release EPB manually, depress the brake pedal, then press the EPB
switch A, with the ignition switch in the ON position . Ensure that the
indicator light is O F F .
REMINDERS:
•
EPB will not release unless the hood, tailgate and all doors are closed and seat belts are fastened
•
As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds when the ignition switch is turned ON
•
If the warning light does not illuminate temporarily, or continues to remain lit, take your vehicle to an authorized Kia dealer and have the system checked
•The EPB should not be operated while the vehicle is moving
•
A click or electric brake motor sound may be heard while operating or releasing the EPB, but these conditions are normal and indicate that the EPB is functioning properly
Auto Hold*
The Auto Hold maintains the vehicle in a standstill even though the brake
pedal is not depressed after the driver brings the vehicle to a complete
stop by depressing the brake pedal .
Depress the brake pedal, start the engine and then press the AUTO HOLD
button B . The white Auto Hold indicator will come on indicating the
system is in standby .
Before the Auto Hold will engage, the driver's door, engine hood and
tailgate must be closed and the driver's seat belt must be fastened .
When coming to a complete stop by depressing the brake pedal, the Auto
Hold indicator changes from white to green indicating the Auto Hold is
engaged and EPB is applied . The vehicle will remain at a standstill even if
you release the brake pedal .
If EPB is applied, Auto Hold will be released .

When leaving your keys with parking lot attendants or valet, make sure to inform them how to operate the EPB
QUICK TIP
BA

*IF EQUIPPED 35ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
OTHER KEY FEATURES
HOLD
L ock U
nlo ck
L ock U
nlo ck
Double-Turn Lock/Unlock All
•Turn clockwise once to unlock
driver’s door
•Turn clockwise again within
4 seconds to unlock all doors
•Turn counterclockwise once
to lock all doors
Remote Keyless Entry (Folding Key)*Fuel Door Release
Fuel Cap / Malfunction Indicator
(Check Engine Light)
A Press the release button to unfold the key
B Press to lock all doors
C
Press to unlock driver’s door . Press
twice in 4 seconds to unlock all doors
and liftgate
D Press and hold to unlock liftgate and
manually open
E Press and hold more than 1 second for
Panic Alarm . To turn OFF Alarm, press
any button
To open the fuel door, press the right edge of
the fuel door .
REMINDER:
The fuel door lock will unlock /open only when driver's side door is unlocked .
Tighten for ONE CLICK to prevent Malfunction
Indicator from illuminating .
REMINDERS:
• To open the fuel door, press the right edge of the fuel door .
•
It is normal operation when tightening to hear one click and then when Fuel Cap is released, it clicks back .
REMINDER:
•
The liftgate does not automatically open when the D button is pressed
•
The liftgate unlocks when the Smart Key is within close proximity of the vehicle
•
Remote button configuration may vary depending on vehicle options
One-Click Fuel Cap Video To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
www.youtube.com/KiaFeatureVideos
QR CODE
B
C
D
E
A
HOLD
Lock U
nlo ck
L ock U
nlo ck
HOLD
L ock U
nlo ck
L ock U
nlo ck

36*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
OTHER KEY FEATURES
HomeLink® with Auto-Dimming
Rearview Mirror*
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON .
The HomeLink®/Auto-Dimming Rearview Mirror* is designed to
reduce glare from a vehicle’s headlights located in the rear and also
connect up to three electronic transmitters into one location .
•
To turn automatic dimming ON, press button F
•
To turn automatic dimming OFF, press button G
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information) .
To program non-rolling and rolling code garage door openers and other
devices:
1 . Press and hold the left A and center D buttons simultaneously until the
indicator light C begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A, B or D and hold the button on the
transmitter while it is approximately 1 to 3 inches away from the mirror .
The HomeLink® Indicator light C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers, complete these
steps:
3 .
Locate the “learn” or “smart” button on the garage door’s motor head unit .
Press and release the button and complete Step 4 within 30 seconds .
4 . Firmly press and release the programmed HomeLink® button up to three
times .
• You can reprogram a single HomeLink® button by repeating Step 2• Erasing programmed buttons will delete all trained transmitters
QUICK TIP
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the left A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds .

*IF EQUIPPED 37ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
OTHER KEY FEATURES
Map/Room LampsPanoramic Sunroof Operation*
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after
the ignition or Engine Start /Stop button* is OFF .
Map Lamp/Room Lamp Operation
Push the lens A to turn the map lamp ON/OFF . This light produces a spot
beam for convenient use as a map lamp or as a personal lamp for the
driver or the front passenger .
Map/Room Lamp Button – Press button B, to turn the front and rear
room lamps on and off .
Door Mode Button – Press button C, to enable or disable Door Mode .
In Door Mode, the map and room lamps turn on when any door is opened .
When all doors are locked or the ignition is on, the map and room lamp
will turn off immediately .
Rear Room Lamps – Press the button D
to turn the rear passenger lamp ON/OFF .
The sunroof operation is controlled through a multi-directional switch/
lever . The ignition or Engine Start /Stop button* needs to be in the ON
position to operate the sunroof .
To slide the sunshade and sunroof:
• Auto Open: Slide the lever E backward to the farthest position and
release
• Auto Close (sunroof only): Slide the lever E forward to the farthest
position and release
To slide the sunshade only:
•
Open: Slide the lever E partially backward to the first detent position
and release
• Auto Close: Slide the lever E partially forward to the first detent
position and release
To slide the sunroof (with sunshade open):
• Open: Slide the lever E backward to the first detent position and
release
• Close: Slide the lever E forward to the first detent position and
release to close sunroof glass only . Slide the lever backward to the
farthest position and release to close sunroof glass and sunshade
To tilt the sunroof:
• Raise: Push lever E upward .
• Lower: Push lever E upward again
or slide the lever forward to the
first detent position and release
• When doors are unlocked by the Smart Key, the lamp turns ON for approximately 30 seconds
• If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 3 seconds after the system is in armed stage
• Using interior lights for an extended period of time may cause battery discharge
QUICK TIP
To stop the sunroof/sunshade at any position, push or pull the sunroof control lever in any direction .
QUICK TIP
AA
BCE
D
REMINDERS:
• Sunshade needs to remain OPEN while sunroof is open and vehicle is moving
• Sunshade cannot slide when it is in the tilt position or tilt while in an open or slide position
( Type B)

*IF EQUIPPED 39ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
OTHER KEY FEATURES
REMINDERS:
•All doors are closed and locked after about 15 seconds
•The Smart Power Liftgate feature will not operate when:
- The doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles- A door is not locked or closed- The Smart Key is in the vehicle
•
Press any button on the Smart Key fob during the Detect and Alert stage to deactivate the Smart Power Liftgate function .
Smart Power Liftgate Video
To view a video on your mobile device, snap this QR Code or visit the listed website .
Refer to page 2 for more information .
www.youtube.com/KiaFeatureVideos
QR CODE
• During the Smart Power Liftgate alert, the Smart Power Liftgate can be deactivated with the Smart Key by pressing any button on the key fob .
• The open height can be adjusted . For information on how to set open height, see your owner's manual
QUICK TIPS
HOLD
C
Liftgate Release ButtonSmart Power Liftgate*
Located underneath the rear liftgate hatch . With
liftgate unlocked, press the Liftgate Release Button A and pull the liftgate up by the handle to open .
• The liftgate must be unlocked before it can be opened by the Liftgate Release Button
• aThe liftgate unlocks automatically, and can then be opened, when the Smart Key fob* is within close proximity to the vehicle
QUICK TIPS

HOLD
(Liftgate release button)
A
When the Smart Key fob is on your person and you are near
the back of the vehicle, within close proximity, the hazard
lights will blink and a chime will sound for about 3 seconds
as an alert that the Smart Power Liftgate is about to open .
Then the alert system will blink and chime two additional
times before opening the Smart Power Liftgate .
The Smart Power Liftgate
feature is off by default . To
enable the Smart Power
Liftgate, go to User Settings
in the LCD Instrument
Cluster modes .

40*IF EQUIPPED SPORTAGE FEATURES & FUNCTIONS GUIDE
OTHER KEY FEATURES
Child-Protector Rear Door Lock
Located on the rear edge of the rear passenger doors .
Insert the ignition key into the hole and turn the key
to the LOCK position to disable the inner door handles
from opening the rear doors .
REMINDER: Child-Protector Rear Door Lock is located on rear passenger’s door jamb .
Sunvisor
Use the sunvisor to shield direct light through the front or side windows .
To adjust, move sunvisor left or right .
(Located on rear edge of rear passenger doors)
REMINDERS:
• Sunvisor may not shield all direct light
• The sunvisor may impair visibility if not adjusted properly
• Do not operate the vehicle if the sunvisor is impairing your visibility
• Be aware of seating position when adjusting or swinging sunvisor around to or from the front or side windows
(Rear Camera)(Rear Camera Display)
Rear-Camera Display*
REMINDER:
While camera is active, only the volume controls on the Audio System can be operated

The Rear-Camera Display is not a substitute for proper and safe backing-up procedures. Always drive safely and use caution when backing up. The Rear-Camera Display may not detect every object behind the vehicle.
The Rear-Camera Display system is not a safety device . It is a
supplemental system that displays the view behind the vehicle through the
Standard Audio System, UVO eServices System* or UVO eServices with
Premium Navigation* screens while the vehicle is in Reverse .
The Rear-Camera Display activates when the:
1 . Engine Start /Stop* button is in the ON position (Green Light)
2 .
Gear Shift Lever is in the R (Reverse) position
P
R
N
DSHIFTL OCK
RELEASE