light KIA STONIC 2018 Owners Manual

NOTICE
•When operating the vehicle on a
dynamometer, ensure that the
ESC is turned off (ESC OFF light il‐
luminated).
•Turning the ESC off does not af‐
fect ABS or brake system opera‐
tion.
WARNING
Never press the ESC OFF buttonwhile ESC is operating.If the ESC is turned off while ESC isoperating, the vehicle may go out ofcontrol.To turn ESC off while driving, pressthe ESC OFF button while driving ona flat road surface.
Hill-start assist control (HAC) (if
equipped)
Hill start Assist Control is a comfort
function. The main intend is to prevent the vehicle from rolling backwards
while driving off uphill on an inclined
surface. HAC holds the braking pressure
builtup by driver during stopping proce‐ dure for 2 seconds after releasing
brake pedal.
During the pressure-hold period, the
driver has enough time to press the ac‐ celerator pedal to drive off.
The braking pressure is reduced as
soon as the system detects the driver’s
intention to drive off.
WARNING
The HAC is usually activated only for2 seconds. The driver should becareful from the rolling backwardcausing the accident with behind ob‐jects or human, when the driver mayfeel the unintended rolling backwardwhile driving off on hill due to insuf‐ficient brake hold pressure built-upby driver during stopping procedure.
NOTICE
•The HAC does not operate when
the transaxle shift lever is in the P
(Park) or N (Neutral) position.
•The HAC activates even though
the ESC is off but it does not acti‐
vate when the ESC has malfunc‐
tioned.
Vehicle stability management
(VSM) (if equipped)
This system provides further enhance‐
ments to vehicle stability and steering responses when a vehicle is driving on a
slippery road or a vehicle detected
changes in coefficient of friction be‐ tween right wheels and left wheels
when braking.
VSM operation
When the VSM is in operation, ESC indi‐
cator light () blinks.
When the vehicle stability management
is operating properly, you can feel a slight pulsation in the vehicle. This is
only the effect of brake control and in‐
dicates nothing unusual.

6-39
6
Driving your vehicle

The VSM does not operate when:
• Driving on bank road such as gradient or incline
• Driving rearward
• ESC OFF indicator light (
) remains
on the instrument cluster
• EPS indicator light remains on the in‐ strument cluster
VSM operation off
If you press the ESC OFF button to turn
off the ESC, the VSM will also cancel and the ESC OFF indicator light (
) il‐
luminates.
To turn on the VSM, press the button again. The ESC OFF indicator light goes
out.
Malfunction indicator
The VSM can be deactivated even if you
don’t cancel the VSM operation by pressing the ESC OFF button. It indi‐
cates that a malfunction has been de‐
tected somewhere in the Electric Pow‐ er Steering system or VSM system.
If the ESC indicator light (
) or EPS
warning light remains on, have the sys‐ tem checked by a professional work‐
shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner.
NOTICE
•The VSM is designed to function
above approximately 15 km/h (9
mph) on curves.
•The VSM is designed to function
above approximately 30 km/h (18
mph) when a vehicle is braking on
a split-mu road. The split-mu road
is made of surfaces which have
different friction forces.
WARNING
•The Vehicle Stability Managementsystem is not a substitute for safedriving practices but a supplemen‐tary function only. It is the respon‐sibility of the driver to alwayscheck the speed and the distanceto the vehicle ahead. Always holdthe steering wheel firmly whiledriving.
(Continued)
(Continued)
•Your vehicle is designed to activateaccording to the driver’s intention,even with installed VSM. Alwaysfollow all the normal precautionsfor driving at safe speeds for theconditions – including driving in‐clement weather and on a slipperyroad.
•Driving with varying tire or wheelsizes may cause the VSM systemto malfunction. When replacingtires, make sure they are thesame size as your original tires.
ESS : Emergency Stop Signal (if
equipped)
The Emergency Stop Signal system
alerts the driver behind by blinking the stop light when the vehicle suddenly
stops or when the ABS activates in a
stop. (The system activates when the vehicle speed is over 55km/h and the
vehicle deceleration is over 7m/s² or the
ABS activates when the vehicle emer‐ gency braking.)
When the vehicle speed is under 40
km/h and the ABS deactivates or the
sudden stop situation is over, the stop light blinking will stop.
Driving your vehicle
6-40

CAUTION
The Emergency Stop Signal systemwill not work if the hazard warningflasher is already on.
Good braking practices
WARNING
•Whenever leaving vehicle or park‐ing, always set the parking brakeas far as possible and fully engagethe vehicle's transaxle into thepark position. Vehicles not fully en‐gaged in park with the parkingbrake set are at risk for moving in‐advertently and injuring yourselfor others.
•All vehicles should always have theparking brake fully engaged whenparking to avoid inadvertentmovement of the car which can in‐jure occupants or pedestrians.
• After parking the vehicle, check to besure the parking brake is not engaged
and that the parking brake indicator light is out before driving away. • Driving through water may get the
brakes wet. They can also get wet
when the car is washed. Wet brakes
can be dangerous! Your car will not
stop as quickly if the brakes are wet. Wet brakes may cause the car to pull
to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns
to normal, taking care to keep the car
under control at all times. If the brak‐ ing action does not return to normal,
stop as soon as it is safe to do so and
have your vehicle inspected by a pro‐
fessional workshop.
Kia recommends to call an authorized Kia dealer/service partner.
• Don't coast down hills with the car out of gear. This is extremely hazard‐
ous. Keep the car in gear at all times,
use the brakes to slow down, then
shift to a lower gear so that engine braking will help you maintain a safe
speed.
• Don't "ride" the brake pedal. Resting your foot on the brake pedal while
driving can be dangerous because it
can result in the brakes overheating and losing their effectiveness. It also
increases the wear of the brake com‐
ponents. • If a tire goes flat while you are driv‐
ing, apply the brakes gently and keepthe car pointed straight ahead while
you slow down. When you are moving
slowly enough for it to be safe to do
so, pull off the road and stop in a
safe place.
• If your car is equipped with an auto‐ matic transaxle, don't let your car
creep forward. To avoid creeping for‐
ward, keep your foot firmly on the
brake pedal when the car is stopped.
• Be cautious when parking on a hill. Firmly engage the parking brake andplace the shift lever in P (Park). If
your car is facing downhill, turn the
front wheels into the curb to help
keep the car from rolling. If your car is facing uphill, turn the front wheels
away from the curb to help keep the
car from rolling. If there is no curb or
if it is required by other conditions to
keep the car from rolling, block the wheels.

6-41
6
Driving your vehicle

CRUISE CONTROL SYSTEM (IF EQUIPPED)
The cruise control system allows you to
program the vehicle to maintain a con‐
stant speed without pressing the accel‐ erator pedal.
This system is designed to function
above approximately 30 km/h (20
mph).
WARNING
•If the cruise control is left on,(CRUISE indicator light in the in‐strument cluster illuminated) thecruise control can be switched onaccidentally. Keep the cruise con‐trol system off (CRUISE indicatorlight OFF) when the cruise controlis not in use, to avoid inadvertent‐ly setting a speed.
•Use the cruise control system onlywhen traveling on open highwaysin good weather.
(Continued)
(Continued)
•Do not use the cruise control whenit may not be safe to keep the carat a constant speed, for instance,driving in heavy or varying traffic,or on slippery (rainy, icy or snow-covered) or winding roads or over6% uphill or down-hill roads.
•Pay particular attention to thedriving conditions whenever usingthe cruise control system.
CAUTION
During cruise-speed driving of amanual transaxle vehicle, do notshift into neutral without depressingthe clutch pedal, since the enginewill be over-revved. If this happens,depress the clutch pedal or releasethe cruise control ON-OFF switch.
NOTICE
During normal cruise control opera‐
tion, when the SET switch is activa‐
ted or reactivated after applying the
brakes, the cruise control will ener‐
gize after approximately 3 seconds.
This delay is normal.
NOTICE
To activate cruise control, depress
the brake pedal at least once after
turning the ignition switch to the ON
position or starting the engine. This
is to check if the brake switch which
is important part to cancel cruise
control is in normal condition.

6-43
6
Driving your vehicle

¥
5ZQF
$
1. Press the cruise /CRUISE/ but‐
ton on the steering wheel, to turn
the system on. The cruise indicator
light will illuminate.
2. Accelerate to the desired speed, which must be more than 30 km/h
(20 mph).
NOTICE
nManual transaxle
For manual transaxle vehicles, you
should depress the brake pedal at
least once to set the cruise control
after starting the engine.
¥
5ZQF
"
¥
5ZQF
#3. Move the lever down (to SET-), and release it at the desired speed. The
cruise set indicator light will illumi‐
nate. Release the accelerator pedal
at the same time. The desired
speed will automatically be main‐
tained.
On a steep grade, the vehicle may slow
down or speed up slightly while going downhill.

6-45
6
Driving your vehicle

¥
5ZQF
$
• Depress the brake pedal.
• Depress the clutch pedal if equippedwith a manual transaxle.
• Shift into N (Neutral) if equipped with an automatic transaxle.
• Press the O/CANCEL switch located on the steering wheel.
• Decrease the vehicle speed lower than the memory speed by 20 km/h
(12 mph).
• Decrease the vehicle speed to less than approximately 30 km/h (20
mph).
Each of these actions will cancel cruise
control operation (the cruise set indica‐tor light will go off), but it will not turn the system off. If you wish to resume cruise control operation, move up thelever (to RES+) located on your steering wheel. You will return to your previous‐ly preset speed.To resume cruising speed at
more than approximately 30
km/h (20 mph):
¥
5ZQF
"
¥
5ZQF
#
Driving your vehicle
6-48

If any method other than the cruise /
CRUISE/ button was used to cancel
cruising speed and the system is still
activated, the most recent set speed will automatically resume when you
move the lever up (to RES+).
It will not resume, however, if the vehi‐
cle speed has dropped below approxi‐ mately 30 km/h (20 mph).
To turn cruise control off, do
one of the following:
• Press the cruise /CRUISE/ button
(the cruise indicator light will be turn
off).
• Turn the ignition off.
Both of these actions cancel cruise con‐ trol operation. If you want to resumecruise control operation, repeat thesteps provided in L

SPEED LIMIT CONTROL SYSTEM (IF EQUIPPED)
You can set the speed limit when you
do not want to drive over a specific
speed.
If you drive over the preset speed limit, the warning system operates (set
speed limit will blink and chime will
sound) until the vehicle speed returns within the speed limit.
NOTICE
While speed limit control is in opera‐
tion, the cruise control system can‐
not be activated.
Speed limit control switch
O: Cancels set speed limit.
: Turns speed limit control sys‐ tem on or off.
RES+ : Resumes or increases speed
limit control speed.
SET- : Sets or decreases speed limit
control speed.
To set speed limit:
1. Press the speed limit button
twice on the steering wheel, to
turn the system on.
The speed limit indicator light will
illuminate.
2. Move the lever down (to SET-).
Driving your vehicle
6-50

FORWARD COLLISION-AVOIDANCE ASSIST (FCA) SYSTEM (IF EQUIPPED)
The FCA system is to reduce or to avoid
accident risk. It recognizes the distance
from the vehicle ahead or the pedes‐ trian through the sensors (i.e. radar
and camera), and, if necessary, warns
the driver of accident risk with the warning message or the warning
alarms.
WARNING
Take the following precautions whenusing the Forward Collision-Avoid‐ance Assist (FCA) System:•This system is only a supplemen‐tal system and it is not intendedto, nor does it replace the need forextreme care and attention of thedriver. The sensing range and ob‐jects detectable by the sensors arelimited. Pay attention to the roadconditions at all times.
•NEVER drive too fast in accordancewith the road conditions or whilecornering.
(Continued)
(Continued)
•Always drive cautiously to preventunexpected and sudden situationsfrom occurring. FCA does not stopthe vehicle completely and doesnot avoid collisions.
System setting and activation
System setting
The driver can activate the FCA by plac‐
ing the ignition switch to the ON posi‐
tion and by selecting 'User Settings', 'Driving Assist', and 'Forward Collision-
Avoidance Assist (FCA)'. The FCA deac‐
tivates, when the driver cancels the system setting.
The warning light illuminates on the LCD display, when youcancel the FCA system.
The driver can monitor the FCAON/OFF status on the LCD display.
When the warning light remains ON
with the FCA activated, have the sys‐tem checked by a professional work‐
shop. Kia recommends to visit an au‐
thorized Kia dealer/service partner. The driver can select the initial warning
activation time in the User Settings and Driving Assist in the instrument cluster
LCD display. The options for the initial
Forward Collision Warning include the following:
• EARLY - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted earlier than normal.This setting maximizesthe amount of distance
between the vehicle or
pedestrian ahead beforethe initial warning occurs.
• NORMAL - When this condition is se‐
lected, the initial Forward
Collision Warning is activa‐ted normally. This settingallows for a nominalamount of distance be‐
tween the vehicle or pe‐
destrian ahead before theinitial warning occurs.
• LATE - When this condition is se‐ lected, the initial Forward
Collision Warning is activa‐ted later than normal.
This setting reduces theamount of distance be‐

6-53
6
Driving your vehicle

WARNING
The FCA operates in accordance withthe risk levels, such as the distancefrom the vehicle/passer-by in front,the speed of the vehicle/passer-byin front, and the driver's vehicle op‐eration.
Sensor to detect the distance
from the vehicle in front (front
radar)
0:#%
The sensor is to maintain a certain dis‐
tance from the vehicle in front. Howev‐ er, the smudged sensor lens with for‐
eign substances, such as snow and rain,
adversely affects the sensing perform‐ ance. It may even temporarily cancel
the FCA. Always keep the sensor lens
clean.
Warning message and warning light
0:#-
When the sensor cover or the sensor
lens is smudged with the foreign sub‐ stances, such as snow or rain, the FCA
operation may temporarily stop. In this
case, the warning message appears to warn the driver.
This is not a malfunction with the FCA.
To operate the FCA again, remove the
foreign substances.
If the sensor is smudged entirely or no object is sensed (in an open terrain
etc.), The FCA might not operate nor‐
mally.
Driving your vehicle
6-56