warning KIA STONIC 2018 Owners Manual

Compact spare tire replacement (if
equipped)
A compact spare tire has a shortertread life than a regular size tire. Re‐
place it when you can see the tread
wear indicator bars on the tire. The re‐ placement compact spare tire should be
the same size and design tire as the
one provided with your new vehicle and
should be mounted on the same com‐ pact spare tire wheel. The compact
spare tire is not designed to be moun‐
ted on a regular size wheel, and the compact spare tire wheel is not de‐
signed for mounting a regular size tire.
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new wheels are equivalent to the original factory
units in diameter, rim width and offset.
WARNING
A wheel that is not the correct sizemay adversely affect wheel andbearing life, braking and stoppingabilities, handling characteristics,ground clearance, body-to-tire
(Continued)
(Continued)
clearance, snow chain clearance,speedometer and odometer calibra‐tion, headlight aim and bumperheight.
Tire traction
Tire traction can be reduced if you drive
on worn tires, tires that are improperly inflated or on slippery road surfaces.
Tires should be replaced when tread
wear indicators appear. Slow down whenever there is rain, snow or ice on
the road to reduce the possibility of
losing control of the vehicle.
Tire maintenance
In addition to proper inflation, correct
wheel alignment helps to decrease tire wear. If you find a tire is worn uneven‐
ly, have a professional workshop check
the wheel alignment. Kia recommends to visit an authorized Kia dealer/service
partner.
When you have new tires installed,
make sure they are balanced. This will increase vehicle ride comfort and tire
life. Additionally, a tire should always
be rebalanced if it is removed from the wheel.
Tire sidewall labeling
This information identifies and de‐
scribes the fundamental characteristics of the tire and also provides the tire
identification number (TIN) for safety
standard certification. The TIN can be used to identify the tire in case of a re‐
call.
1. Manufacturer or brand name
Manufacturer or Brand name is shown.
Maintenance
8-72

WARNING
nTire age
Tires degrade over time, even whenthey are not being used.Regardless of the remaining tread,we recommend that tires be re‐placed after approximately six (6)years of normal service. Heat causedby hot climates or frequent highloading conditions can accelerate theaging process. Failure to follow thiswarning can result in sudden tirefailure, which could lead to a loss ofcontrol and an accident involving se‐rious injury or death.
4. Tire ply composition and material
The number of layers or plies of rub‐
ber-coated fabric in the tire. Tire man‐ ufacturers also must indicate the ma‐
terials in the tire, which include steel,
nylon, polyester, and others. The letter "R" means radial ply construction; the
letter "D" means diagonal or bias ply
construction; and the letter "B" means belted-bias ply construction.
5. Maximum permissible inflation
pressure
This number is the greatest amount of
air pressure that should be put in the
tire. Do not exceed the maximum per‐ missible inflation pressure. Refer to the
Tire and Loading Information label for
recommended inflation pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that can be carried by the tire. When replacing
the tires on the vehicle, always use a
tire that has the same load rating as the factory installed tire.
7. Uniform tire quality grading
Quality grades can be found where ap‐
plicable on the tire sidewall between tread shoulder and maximum section
width.
For example:TREADWEAR 200TRACTION AA
TEMPERATURE A
Tread wear
The tread wear grade is a comparative
rating based on the wear rate of the tire when tested under controlled con‐
ditions on a specified government test
course. For example, a tire graded 150 would wear one-and-a-half times (1½)
as well on the government course as a
tire graded 100.
The relative performance of tires de‐ pends upon the actual conditions of
their use, however, and may depart sig‐
nificantly from the norm due to varia‐
tions in driving habits, service practices and differences in road characteristics
and climate.
These grades are molded on the side-
walls of passenger vehicle tires. The tires available as standard or optional
equipment on your vehicle may vary
with respect to grade.
Traction - AA, A, B & C
The traction grades, from highest to lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured under controlled conditions on specified
government test surfaces of asphalt
and concrete. A tire marked C may have poor traction performance.
Maintenance
8-74

Temperature - A, B & C
The temperature grades are A (the
highest), B, and C, representing the tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi‐ tions on a specified indoor laboratory
test wheel.
Sustained high temperature can cause
the material of the tire to degenerate and reduce tire life, and excessive tem‐
perature can lead to sudden tire failure.
Grades B and A represent higher levels of performance on the laboratory test
wheel than the minimum required by
law.
WARNING
The traction grade assigned to thistire is based on straight-ahead brak‐ing traction tests, and does not in‐clude acceleration, cornering, hydro‐planing, or peak traction characteris‐tics.
WARNING
nTire temperature
The temperature grade for this tireis established for a tire that is prop‐erly inflated and not overloaded. Ex‐cessive speed, underinflation, or ex‐cessive loading, either separately orin combination, can cause heat build-up and possible sudden tire failure.This can cause loss of vehicle controland serious injury or death.
Low aspect ratio tire (if
equipped)
Low aspect ratio tires, whose aspect
ratio is lower than 50, are provided for sporty looks.
Because the low aspect ratio tires are
optimized for handling and braking, it
may be more uncomfortable to ride in and there is more noise compare with
normal tires.
CAUTION
Because the sidewall of the low as‐pect ratio tire is shorter than the
(Continued)
(Continued)
normal, the wheel and tire of thelow aspect ratio tire is easier to bedamaged. So, follow the instructionsbelow.•When driving on a rough road oroff road, drive cautiously becausetires and wheels may be damaged.And after driving, inspect tires andwheels.
•When passing over a pothole,speed bump, manhole, or curbstone, drive slowly so that thetires and wheels are not damaged.
•If the tire is impacted, inspect thetire condition or contact a profes‐sional workshop. Kia recommendsto visit an authorized Kia dealer/service partner.
•To prevent damage to the tire, in‐spect the tire condition and pres‐sure every 3,000km.

8-75
8
Maintenance

FUSES
¥
#MBEF
UZQF
¥
$BSUSJEHF
UZQF
¥
.VMUJ


GVTF ¥
#'5
❈Left side : Normal Right side : Blown
A vehicle’s electrical system is protec‐
ted from electrical overload damage by fuses.
This vehicle has 2 (or 3) fuse panels,
one located in the driver’s side panel
bolster, the others in the engine com‐ partment near the battery.
If any of your vehicle’s lights, accesso‐
ries, or controls do not work, check the
appropriate circuit fuse. If a fuse has blown, the element inside the fuse will
melt.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, discon‐ nect the negative battery cable.
Always replace a blown fuse with one
of the same rating.
If the replacement fuse blows, this indi‐
cates an electrical problem. Avoid using the system involved and immediately
consult a professional workshop. Kia
recommends to consult an authorized Kia dealer/service partner.
Three kinds of fuses are used: blade
type for lower amperage rating, car‐
tridge type, and multi fuse for higher amperage ratings.
WARNING
nFuse replacement
•Never replace a fuse with anythingbut another fuse of the same rat‐ing.
•A higher capacity fuse could causedamage and possibly a fire.
•Never install a wire or aluminumfoil instead of the proper fuseeven as a temporary repair. It maycause extensive wiring damageand a possible fire.
•Do not arbitrarily modify or add-on electric wiring of the vehicle.
CAUTION
Do not use a screwdriver or any oth‐er metal object to remove fuses be‐cause it may cause a short circuitand damage the system.

8-77
8
Maintenance

If you do not have a spare, use a fuse
of the same rating from a circuit you may not need for operating the vehicle,
such as the cigarette lighter fuse.
If the headlights or taillights, stoplights,
courtesy lamp, day time running lights (D.R.L) do not work and the fuses are
OK, check the fuse panel in the engine
compartment. If a fuse is blown, it must be replaced.
Memory fuse
0:#
Your vehicle is equipped with a memory
fuse to prevent battery discharge if your vehicle is parked without being op‐
erated for prolonged periods. Use the
following procedures before parking the
vehicle for prolonged periods. 1. Turn off the engine.
2. Turn off the headlights and tail
lights.
3. Open the driver’s side panel cover and pull up the memory fuse.
NOTICE
•If the memory fuse is pulled up
from the fuse panel, the warning
chime, audio, clock and interior
lamps, etc., will not operate. Some
items must be reset after replace‐
ment. Refer to L

SymbolFuse rat‐ingCircuit Protected
10ABCM (Body Control Module), Crash Pad Switch, FCA Unit, Lane Departure Warning System, BLIND-
SPOT DETECTION WARNING Radar LH/RH
15AEngine Room Junction Block(Back-Up Lamp Switch), Sport Mode Switch, Speed Sensor, Stop Lamp
Switch, Speed Sensor (In/Out), Transaxle Range Switch
LH25A Power Window Main Switch, Passenger Power Window Switch(RHD)
SPARE25A Spare
10A Rear Fog Lamp Relay
15A Clock Spring
LH7.5A Head Lamp LH, License Lamp LH(Sedan), Rear Combination Lamp (IN) LH(Wagon)
7.5A Front Console Switch, Front Seat Warmer Control Module, Audio, Audio / Video & Navigation Head
Unit, Head Lamp Leveling Device Actuator LH/RH, Air Conditioner Control Module, Electro Chromic
Mirror, Crash Pad Switch, DC-DC Converter, Clock Spring, A/T Shift Lever Indicator
7.5A
Engine Room Junction Block(Multipurpose Check Connector), ABS/ESC (Electronic Stability Control)
Control Module
10A Smart Key Control Module, Stop Lamp Switch
SPARE15A Spare
15A Front Fog Lamp Relay
7.5AEngine Room Junction Block(Air Conditioner Blower Relay), GSL Junction Block(PTC Heater Relay),
DSL Junction Block(Start Relay, Air Conditioner Blower Relay), Air Conditioner Control Module
MODULE510AEngine Room Junction Block(Head Lamp High Relay, Head Lamp Relay), Front Seat Warmer Control
Module, BCM (Body Control Module)


8-85
8
Maintenance

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
0:##
1. Open the hood.
Maintenance
8-110

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Static bending light replacement
(Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
Maintenance
8-112

License plate lamp bulb
replacement
0:##
1. Using a flat-blade screwdriver, gen‐tly pry the lens cover from lamp
housing.
2. Remove the socket from the as‐ sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
3. Remove the bulb from bulb-socket by pulling it out.
4. Insert a new bulb by inserting it in‐ to the bulb-socket. 5. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
6. Align the lens cover tabs with the lamp housing notches and snap the
lens into place.
Map lamp bulb replacement
WARNING
Prior to working on the Interiorlamps, ensure that the L

Vanity mirror lamp bulb
replacement
WARNING
Prior to working on the Interiorlamps, ensure that the L