fog light KIA STONIC 2018 Owners Manual

User Settings Mode (for type C, D cluster)...................... 4-59
Warning messages................................................................4-61
Warning and indicator lights................................................... 4-65 Warning lights........................................................................ 4-65
Indicator Lights...................................................................... 4-72
Rear parking assist system ....................................................4-76 Operation of the rear parking assist system................... 4-76
Non-operational conditions of rear parking as‐
sist system.............................................................................4-77
Rear parking assist system precautions...........................4-77
Self-diagnosis........................................................................ 4-78
Rearview camera ..................................................................... 4-79
Lighting....................................................................................... 4-80 Battery saver function......................................................... 4-80
Headlight escort function ................................................... 4-80
Headlight welcome function .............................................. 4-80
Lighting control..................................................................... 4-81
High beam operation............................................................ 4-83
Turn signals and lane change signals.................................4-84
Front fog light .......................................................................4-85
Rear fog light ........................................................................ 4-86
Static bending light .............................................................. 4-86
Daytime running light ......................................................... 4-87
Headlight leveling device ..................................................... 4-87
High beam Assist ................................................................. 4-88
Wipers and washers................................................................. 4-90 Windshield wipers (front).................................................... 4-90
Windshield washers (front)................................................. 4-92
Rear window wiper and washer switch ........................... 4-93
Interior light............................................................................... 4-95 Map lamp................................................................................ 4-95
Room lamp............................................................................. 4-96
Luggage room lamp ............................................................. 4-96
Vanity mirror lamp .............................................................. 4-96
Glove box lamp...................................................................... 4-97
Defroster.................................................................................... 4-98 Rear window defroster........................................................ 4-98
Manual climate control system ............................................. 4-99 Heating and air conditioning............................................. 4-100
System operation............................................................... 4-104
Climate control air filter ................................................... 4-106
Air Conditioning refrigerant label..................................... 4-106
Checking the amount of air conditioner refriger‐
ant and compressor lubricant...........................................4-107
Automatic climate control system ..................................... 4-108 Automatic heating and air conditioning.......................... 4-109
Manual heating and air conditioning............................... 4-110
System operation............................................................... 4-114
Climate control air filter ................................................... 4-116
Air Conditioning refrigerant label..................................... 4-116
Checking the amount of air conditioner refriger‐
ant and compressor lubricant...........................................4-117
Windshield defrosting and defogging..................................4-118 Manual climate control system........................................ 4-118
Automatic climate control system.................................. 4-119
Defogging logic ................................................................... 4-119
Storage compartments......................................................... 4-122 Center console storage .....................................................4-122
Glove box.............................................................................. 4-122
Sunglass holder .................................................................. 4-123


4

The ignition switch must be on for the
turn signals to function. To turn on the turn signals, move the lever up or down
(A).
The green arrow indicators on the in‐
strument panel indicate which turn sig‐ nal is operating. They will self-cancel
after a turn is completed.
If the indicator continues to flash after
a turn, manually return the lever to the off position.
To signal a lane change, move the turn
signal lever slightly and hold it in posi‐
tion (B). The lever will return to the off position when released.
If an indicator stays on and does not
flash or if it flashes abnormally, one of
the turn signal bulbs may be burned out and will require replacement.
One-touch lane change function (if
equipped)
To activate an one-touch lane change
function, move the turn signal lever slightly and then release it. The lane
change signals will blink 3 times.
NOTICE
If an indicator flash is abnormally
quick or slow, a bulb may be burned
out or have a poor electrical connec‐
tion in the circuit.
Front fog light (if equipped)
¥
5ZQF
"
¥
5ZQF
#

4-85
4
Features of your vehicle

Fog lights are used to provide improved
visibility when visibility is poor due to fog, rain or snow, etc. The fog lights
will turn on when the fog light switch
(1) is turned on after the parklight is turned on.
To turn off the fog lights, turn the fog
light switch (1) to the O (Off) position.
CAUTION
When in operation, the fog lightsconsume large amounts of vehicleelectrical power. Only use the foglights when visibility is poor.
Rear fog light (if equipped)
¥
5ZQF
"
¥
5ZQF
#
To turn the rear fog lights on, turn the
rear fog light switch (1) to the on posi‐ tion when the headlight is turned on. Also, the rear fog lights turn on when
the rear fog light switch is turned on
after the front fog light switch (if equipped) is turned on and the head‐
light switch is in the parklight position.
To turn the rear fog lights off, turn the
rear fog light switch to the on position again.
NOTICE
Rear fog light is only on the driver’s
side (if equipped).
Static bending light (if equipped)
While driving the corner, for your sight
and safety, the static bending light is turned on automatically. The system
will operate automatically as follows. • When turning the headlight on
• When the angle of steering wheel is over 35~40 (it is differed from vehicle
speed)
• When the vehicle speed is over 3 km/h
• When driving forward or backward.
Features of your vehicle
4-86

Daytime running light (if
equipped)
The Daytime Running Lights (DRL) can
make it easier for others to see the front of your vehicle during the day.
DRL can be helpful in many different
driving conditions, and it is especially helpful after dawn and before sunset. The DRL system turns OFF when: 1. The headlight switch is ON.
2. The engine is OFF.
3. The front fog light is on.
4. Engaging the Parking Brake
Headlight leveling device (if
equipped)
0:#
To adjust the headlight beam level ac‐
cording to the number of the passen‐ gers and loading weight in the luggage
area, turn the beam leveling switch.
The higher the number of the switch
position, the lower the headlight beam level. Always keep the headlight beam
at the proper leveling position, or head‐
lights may dazzle other road users.
Listed below are the examples of prop‐ er switch settings. For loading condi‐
tions other than those listed below, ad‐
just the switch position so that the beam level may be the nearest as the
condition obtained according to the list.
Loading conditionSwitch position
Driver only 0
Driver + Front passenger 0
Full passengers
(including driver) 1
Full passengers
(including driver) +Maximum permis‐sible loading 2
Driver + Maximumpermissible load‐ing 3


4-87
4
Features of your vehicle

High beam Assist (if equipped)
0:#
The High Beam Assist is a system that
automatically adjusts the headlamp range (switches between high beam
and low beam) according to the bright‐
ness of other vehicles and road condi‐ tions.
Operating condition
1. Place the light switch in the AUTO position.
2. Turn on the high beam by pushing the lever away from you.
The High Beam Assist (
) indicator
will illuminate. 3. The High Beam Assist will turn on
when vehicle speed is above 45 kph(28 mph). • If the lever is pushed away when the High Beam Assist is operat‐
ing, the High Beam Assist will
turn off and the high beam will
be on continuously. The High
Beam Assist (
) indicator will
turn off.
• If the lever is pulled towards you when the high beam is on with
operating High Beam Assist, theHigh Beam Assist will turn off.
4. If the light switch is placed to the headlamp position, the High Beam
Assist will turn off and the low
beam will be on continuously.
The high beam switches to low beam in
the below conditions. - When the High Beam Assist is off.
- When the light switch is not in the AUTO position.
- When the headlamp is detected from the on-coming vehicle.
- When the tail lamp is detected from the front vehicle.
- When the surrounding is bright enough high beams are not needed. - When streetlights or other lights are
detected.
- When vehicle speed is below 35 km/h (22 mph).
- When headlamp/taillamp of bicycle/ motorcycle is detected.CAUTION
The system may not operate nor‐mally in the below conditions.•When the light from the on-com‐ing or front vehicle is not detectedbecause of lamp damage, hiddenfrom sight, etc.
•When the lamp of the on-comingor front vehicle is covered withdust, snow or water.
•When the light from the on-com‐ing or front vehicle is not detectedbecause of exhaust fume, smoke,fog, snow, etc.
•When the front window is coveredwith foreign matters such as ice,dust, fog, or is damaged.
•When there is a similar shape lampwith the front vehicle’s lamps.
(Continued)
Features of your vehicle
4-88

(Continued)
•When it is hard to see because offog, heavy rain or snow.
•When the headlamp is not repairedor replaced at an authorized deal‐er.
•When headlamp aiming is notproperly adjusted.
•When driving on a narrow curvedroad or rough road.
•When driving downhill or uphill.
•When only part of the vehicle infront is visible on a crossroad orcurved road.
•When there is a traffic light, re‐flecting sign, flashing sign or mir‐ror.
•When the road conditions are badsuch as being wet or covered withsnow.
•When the front vehicle’s head‐lamps are off but the fog lampson.
•When a vehicle suddenly appearsfrom a curve.
(Continued)
(Continued)
•When the vehicle is tilted from aflat tire or being towed.
•When the LDWS (lane departurewarning system) or LKAS (lanekeeping assist system) warninglight illuminates. (if equipped)
WARNING
•Do not place any accessories,stickers or tint the windshield.
•Have the windshield glass replacedfrom an authorized dealer.
•Do not remove or impact relatedparts of the High Beam Assist sys‐tem.
•Be careful that water doesn’t getinto the High Beam Assist unit.
•Do not place objects on the dash‐board that reflects light such asmirrors, white paper, etc. The sys‐tem may malfunction if sunlight isreflected.
(Continued)
(Continued)
•At times, the High Beam Assistsystem may not work properly, al‐ways check the road conditions foryour safety. When the systemdoes not operate normally, man‐ually change between the highbeam and low beam.

4-89
4
Features of your vehicle

Air conditioning (A/C)
Press the A/C button to turn the air
conditioning system on (indicator light will illuminate). Press the button again
to turn the air conditioning system off.
System operation
Ventilation
1. Set the mode to the position.
2. Set the air intake control to the outside (fresh) air position.
3. Set the temperature control to the desired position.
4. Set the fan speed control to the desired speed.
Heating
1. Set the mode to the position.
2. Set the air intake control to the outside (fresh) air position.
3. Set the temperature control to the desired position.
4. Set the fan speed control to the desired speed.
5. If dehumidified heating is desired, turn the air conditioning system (if
equipped) on.
• If the windshield fogs up, set the mode to the
or position.
Operation Tips
• To keep dust or unpleasant fumes from entering the vehicle through the
ventilation system, temporarily set the air intake control to the recircula‐
ted air position. Be sure to return the
control to the fresh air position when
the irritation has passed to keep
fresh air in the vehicle. This will help the driver to stay alert and comfort‐
able. • Air for the heating/cooling system is
drawn in through the grilles just
ahead of the windshield. Care should
be taken that these are not blocked by leaves, snow, ice or other obstruc‐
tions.
• To prevent interior fog on the wind‐ shield, set the air intake control to
the fresh air position and fan speed to the desired position, turn on the
air conditioning system, and adjust
the temperature control to the de‐
sired temperature.
Air conditioning
Kia Air Conditioning Systems are filled
with environmentally friendly refriger‐
ant *
.
1. Start the engine. Push the air con‐ ditioning button.
2. Set the mode to the
position.
* Your vehicle is filled with R-134a or
R-1234yf according to the regula‐tion in your country at the time of
producing. You can find out which air
conditioning refrigerant is applied
your vehicle at the label inside of en‐
gine room. Refer to L

(Continued)
senger compartment may become
stale.
In addition, prolonged use of the air
conditioning with the recirculated air
position selected will result in exces‐
sively dry air in the passenger com‐
partment.
WARNING
•Continued climate control systemoperation in the recirculated airposition may allow humidity to in‐crease inside the vehicle whichmay fog the glass and obscure vis‐ibility.
•Do not sleep in a vehicle with theair conditioning or heating systemon. It may cause serious harm ordeath due to a drop in the oxygenlevel and/or body temperature.
(Continued)
(Continued)
•Continued climate control systemoperation in the recirculated airposition can cause drowsiness orsleepiness, and loss of vehicle con‐trol. Set the air intake control tothe outside (fresh) air position asmuch as possible while driving.
Fan speed control
The fan speed can be set to the desired
speed by operating the fan speed con‐ trol knob.
The higher the fan speed is, the more
air is delivered. Pressing the OFF button turns off the
fan.
Air conditioning (A/C)
Press the A/C button to turn the air
conditioning system on (indicator light will illuminate).
Press the button again to turn the air
conditioning system off.

4-113
4
Features of your vehicle

1. Turn the ignition switch to the ONposition.
2. Turn the mode selection knob to the defrost position (
).
3. Push the air intake control button at least 5 times within 3 seconds.
The indicator light in the air intake con‐
trol button will blink 3 times. It indi‐ cates that the defogging logic is can‐
celed or returned to the programmed
status.
If the battery has been discharged or disconnected, it resets to the defog
logic status.
Automatic climate control system
(if equipped)
1. Turn the ignition switch to the ON position.
2. Select the defrost position pressing defrost button (
).
3. While holding the air conditioning button (A/C) pressed, press the air
intake control button at least 5
times within 3 seconds.
The A/C display blinks 3 times. It indi‐ cates that the defogging logic is can‐
celed or returned to the programmed
status.
If the battery has been discharged or disconnected, it is reset to the defog
logic status.
Auto defogging system (Only for
automatic climate control system,
if equipped)
Auto defogging reduces the possibility
of fogging up the inside of the wind‐ shield by automatically sensing the
moisture of inside the windshield and
air flow toward the windshield can in‐ crease.
The auto defogging system operates
when the AUTO mode is on.
For Europe
If your vehicle is equipped with the auto
defogging system, it is automatically
activated when the conditions are met.
Features of your vehicle
4-120

• The color of the lane marking fromthe road is difficult to distinguish.
• Driving on a steep grade or a curve.
• Light reflects from the water on the road.
• The lens or windshield is stained with foreign matter.
• The sensor can not detect the lane because of fog, heavy rain or heavy
snow.
• The surrounding temperature of the inside rear view mirror is high due to
a direct ray of light.
• The lane is very wide or narrow.
• The lane line is damaged or indistinct.
• The shadow is on the lane line by a median strip.
• There is a mark similar to a lane line.
• There is a boundary structure.
• The distance from vehicle ahead is very short or the vehicle ahead hides
the lane line.
• The vehicle shakes heavily.
• The lane number increases or decrea‐ ses or the lane lines are crossing
complicatedly.
• Putting something on the dashboard. • Driving with the sun in front of you.
• Driving in areas under construction.
• The lane line is more than two in ei‐
ther side (Left/Right).
• The windshield is fogged by humid air in the vehicle.
• The driver turns the wiper switch to HI mode.

6-65
6
Driving your vehicle