LAMBORGHINI GALLARDO 2009 Workshop Manual

Page 1621 of 1659

1
L714 79 74 05
B
A
Fig.1
Fig.2
D
EC
2°1°3°
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
&  ,QVWDOOD]LRQHVLVWHPDPXOWLPHGLDOH.HQZRRG
3URYLGHWKH9,1RIWKHFDURQZKLFKWKH.HQZRRGPXOWLPHGLDV\VWHPZLOOEHLQVWDOOHG LIQRWVXSSOLHG
ZKHQRUGHUHG %HIRUHLQVWDOOLQJZDLWIRUWKH6SDUH3DUWV6DOHV2I¿FHWRFRPPXQLFDWHWKHDYDLODELOLW\
RIWKHQHZ]LS¿OHUHTXLUHGIRUWKHFDU
2SHUD]LRQLSUHOLPLQDUL‡ Disassemble the bench behind the seats – reference B) .
‡ Disassemble the central tunnel  – reference C) .
‡ Disassemble the passenger sun visors  ±UHIHUHQFH:operations 5-6).
‡ Release (don’t remove) the front part of the roof liner ±ULIHULPHQWR: .
‡ Disassemble the roof lamp  .
‡ Disassemble the passenger side lower dashboard assembly UHIHUHQFH5 .
‡ Disassemble the dashboard ±UHIHUHQFH6 .
The Kenwood multimedia system include the navigation and the Bluetooth functions. If the car is equipped
with the Bluetooth optional as original equipment, the Bluetooth ECU has to be removed from the car because it will be not useful with the new Kenwood multimedia system.
The Kenwood multimedia system include the iPod and USB connections; these connections completely replace the original ones that are present in the car if it is equipped with these optional. If the car has the
CD-Changer, this element has to be removed because it is incompatible with the new multimedia system.
6SHFL¿FRSHUDWLRQVIRUFDUVHTXLSSHGZLWKL3RGLQWHUIDFHDVRULJLQDOHTXLSPHQW
Remove the iPod interface
Behind the multimedia system RNS-E of the car, there is a
1. sponge sleeve that contain ($)LJ) the
connection ( %)LJ) between the iPod interface and the RNS-E.
Open (cut) the sponge sleeve and disconnect the two black connectors (
2. %)LJ) that are present inside it.
Remove the green connector (
3. ')LJ  WKDW LV ¿[HG LQ WKH EODFN RQH &)LJ) that was connected to the
multimedia system RNS-E.
Insert the green connector (
4. ')LJ), that was release with the previous operation, in the black connector
( ()LJ ) of the car’s dashboard wiring harness (that was disconnected with the operation 2).

Page 1622 of 1659

2
L714 79 74 05
Fig.3
H
FG
Fig.4
IL
M
1
Fig.5
Q
3
2
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
On the
5. H[WHUQDO VXSHULRU VXUIDFH RI WKH JORYH ER[ WKHUH LV WKH L3RG LQWHUIDFH ())LJ ); disconnect all the
wiring harnesses that are connected with it.
Remove the iPod connection wiring harness (
 *)LJ WKDWJRHVLQVLGHWKHJORYHER[WKURXJKWKH small foam
rubber; remove also the small foam rubber.
:KHQWKHVHVL[RSHUDWLRQZDVEHFDUULHGRXWLWLVSRVVLEOHUHPRYHDOOWKHFRPSRQHQWRIWKHL3RGLQWHUIDFH
7.
system that is present on the car. Remove the iPod interface ( ))LJ) and the iPod interface wiring harness
( +)LJ ) that connect the iPod interface to the multimedia system RNS-E.
2SHUDWLRQHIIHFWLYHIRUDOOFDUV
In order to install the Kenwood multimedia system it’s necessary to replace the original multimedia harness
of the car with the new one supplied with the kit. The new multimedia harness has to be installed as the
original one was positioned in the car; the main difference between the two harness is that the new one has less connection with the car than the original one.
Removing the original multimedia harness (infotainment harness) of the car.
Disconnect the original infotainment harness from the multimedia system (RNS-E) of the car; to carry out this
1.
operation it’s necessary to remove the green
(,)LJ ) and the blue ( /)LJ) connector from the main black
connector
( 0)LJ ) of the RNS-E and to remove the grey/pink connector (1)LJ ) that is connected directly to
the RNS-E (only if the vehicle is equipped with rear view camera or TV-tuner).
If the car is equipped with the Bluetooth system as original equipment, disconnect the little black connector
2.
( 2)LJ ) of the multimedia wiring harness from the black connector of the dashboard wiring harness.
5HPRYH QRWFRPSOHWHO\ WKHFRYHULQJ LQVRXODWLRQVRXQGSURR¿QJ RQWKHGULYHUVLGHRIWKHFHQWUDOWXQQHOLQWKH
3.
car interior (see the Fig.5).
Remove the multimedia harness
4.
( 3)LJ ) that is positioned on the driver side of the central tunnel; to carry out
WKLVRSHUDWLRQLW¶VQHFHVVDU\UHPRYHWKH¿[LQJFOLS (4)LJ WKDW¿[WKHKDUQHVVWRWKHFKDVVLV

Page 1623 of 1659

3
L714 79 74 05
Fig.7
S
T
U
)LJ
:
9
)LJ
43
2
5
1
5
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
Disconnect the original multimedia harness of the car from the kit to the connections on rear bench:
5.
1.If the car is equipped with the Bluetooth system, disconnect the black connector (1)LJ ) from the Bluetooth
ECU.
2.Remove the little loop (2)LJ )RIWKHRULJLQDOPXOWLPHGLDKDUQHVVWKDWLV¿[HG XVLQJWKHSURSHUVFUHZ LQWKH
bushing(2)LJ ) that is present on the rear bench in front of the ECU with the white cap (Bosch ECU).
3.Disconnect the black connector (3)LJ ) of the original multimedia harness to the black one of the central
harness (
3)LJ ) that is present on the rear bench on the left of the ECU with the white cap (Bosch ECU).
4.Remove the connector to the CD-Changer or to the USB interface (4)LJ ).
5.If the vehicle is equipped with the rear view camera, remove the yellow connector (5)LJ ) of the original
multimedia harness from the rear view camera’s ECU.
The connections that are described in the operations 1 and 5 are the all link that could be present on the
car; all these connections are present only if the car is equipped with all the possible multimedia optional. It’s
necessary disconnect only the link that are present; if something that is described here is missing , it’s only
because the proper optional is not present on the car.
Remove the black connector

( 5)LJ ) of the car’s wiring harness that is connected to the RVC control unit.
Removing the multimedia elements that are not compatible with the Kenwood system.
On the rear bench, remove the USB interface
7.( 6)LJ ) or the CD-Changer, if the car is equipped with it.
5HPRYHWKHEUDFNHWWKDW¿[HGWKH86%LQWHUIDFHRUWKH&'&KDQJHUWRFDUU\RXWWKLVRSHUDWLRQLWLVQHFHVVDU\

to remove the three screws
(7)LJ WKDW¿[WKHEUDFNHWWRWKHEHQFK
5HPRYH WKH EUDFNHW WKDW ¿[ WKH %OXHWRRWK FRQWURO XQLW
9.( 8)LJ ) on the rear bench; to do this it’s necessay to
disassemble the two screw on the rear bench and release the joint present in the front part of the bracket. Remove the Bluetooth control unit
10.( 8)LJ ) from the rear bench.
Installation of the new multimedia harness (infotainment harness) on the car.
Lay the new multimedia harness
11.( 9)LJ VXSSOLHGZLWKWKHNLWRQWKHGULYHUVLGHRIWKHFHQWUDOWXQQHODQG¿[LW
XVLQJWKHEXVKLQWKHFKDVVLVDQGWKH¿[LQJFOLSV (:)LJ ) that are present in the new harness. The new harness
has to be positioned so that the the black/yellow jack (video connection) will be placed behind the multimedia system, while the other connections have to be placed on the rear bench.

Page 1624 of 1659

4
L714 79 74 05
Fig.9
12
3
5
Fig.10
Z
4
Fig.11
A
B
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
The following connections have to be carry out on the rear bench:
12.
1.Put to ground the little loop (1)LJ )SUHVHQWRQDZLUHRIWKHQHZPXOWLPHGLDKDUQHVV¿[LWXVLQJWKHSURSHU
screw that have to be insert in the
bushing(1)LJ ) that is present on the rear bench in front of the ECU with
the white cap (Bosch ECU).
2. Link the black connector (2)LJ ) of the new multimedia harness to the black connector of the central
harness (
2)LJ ) that is present on the rear bench on the left of the ECU with the white cap (Bosch ECU).
6SHFL¿FRSHUDWLRQVIRUFDUHTXLSSHGZLWKUHDUYLHZFDPHUD
.
1. The following connections have to be carry out on the rear bench:
3.Connect the brown connector (3)LJ ) of the new multimedia harness to the rear view camera’s
control unit ( =)LJ).
4.Insert the black male connector of the new infotainment harness in the proper connection (4)LJ)
of the rear view camera’s control unit ( =)LJ).
5.Connect the black female connector (5)LJ) of the new multimedia wiring harness to the black
male connector (
5)LJ ) of the car wiring harness that was previously inserted in the rear view
camera’s control unit (removed with the operation 6
( 5)LJ )).
2. Connect the yellow/black video connector ( A)LJ 11) to the Kenwood multimedia system ( B)LJ 11); this
connector has to be connected to the yellow connector ( B)LJ 11) that has the label “rear view camera”
on its own cable.
 2QWKHFDUHTXLSSHGZLWKWKHUHDUYLHZFDPHUDWKHEXWWRQRQWKHFHQWUDOWXQQHOFRQVROHWKDWLV XVHGIRUWKHPDQXDODFWLYDWLRQRIWKHFDPHUDZLOOEHQRORQJHUXVHIXOWKHPDQXDODFWLYDWLRQRI
WKHFDPHUDZLOOEHQRORQJHUSRVVLEOHEXWWKHFDPHUDZLOODXWRPDWLFDOO\VWDUWZKHQWKHUHYHUVH gear will be engaged.

Page 1625 of 1659

5
L714 79 74 05
D
C
E
Fig.12
GH
F
Fig.13
Fig.14
M
L
I
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
2SHUDWLRQHIIHFWLYHIRUDOOFDUV
2Q WKH FDUV ZLWKRXW UHDU YLHZ FDPHUD WKH IUHH FRQQHFWLRQV KDYH WR EH ¿[HG WR VRPH VXSSRUWV XVLQJ WKHblack clamps that are supplied with the kit.
$VVHPEO\RIWKHQHZVSHFL¿FEUDFNHWRIWKHQHZ.HQZRRGPXOWLPHGLDV\VWHP
Remove the supporting bracket 13. (C )LJ 12) of the RNS-E multimedia system. To carry out this operation, in the
internal side of the dashboard it is necessary to remove the 6 screws, 2 upside the bracket
( D )LJ 12) and 2 on
each lateral side
( E )LJ 12)RIWKHEDFNHWWKDW¿[WKHEUDFNHWWRWKHGDVKERDUG
As shown in the picture beside
14. (Fig.13 ), assemble the rubber buffer ( G)LJ 13) supplied with the kit on the rear
part of the new supporting bracket ( )Fig.13 ) (supplied with the kit) of the Kenwood multimedia system.
Insert in the new supporting bracket 15. () Fig.13 ) WKH VSHFL¿F VOLGH(H )LJ 13) supplied with the kit that is useful
WR¿[WKH.HQZRRGV\VWHP
; this slide ( H )LJ 13) has to be inserted frontally in the bracket and then it has to be
pushed (as showed by the yellow arrows in the picture beside) until it will be blocked in the supporting bracket
.
Assemble the new supporting bracket, with the slide and the buffer, on the central console of the car’s dashboard.

7KLV QHZ VXSSRUWLQJ EUDFNHW KDV WR EH ¿[HG LQ WKH VDPH ZD\ RI RULJLQDO RQH WR FDUU\ RXW WKLV RSHUDWLRQ LW LV QHFHVVDU\ WR ZRUN LQVLGH WKH GDVKERDUG DQG WR XVH WKH VDPH  VFUHZV DQG ¿[LQJ SRLQWV RQ WKH GDVKERDUG 2
upside and 2 on each lateral side of the bracket
WKDWZDVXVHGWR¿[WKHRULJLQDOEUDFNHW,ILWLVQHFHVVDU\XVH
also the 6 clips supplied with the kit.
Assembly of the new GPS antenna.
In the area behind the kombi, remove the original GPS antenna of the multimedia system RNS-E (
17. /Fig.14 ) from
the proper bracket ( ,Fig.14 ).
Assemble the new GPS antenna (
 0 Fig.14) supplied with the kit (it is inside the Kenwood package) on the same
bracket ( ,Fig.14 ). The new GPS antenna ( 0Fig.14 KDVWREH¿[HGXVLQJWKHPDJQHWSUHVHQWRQLWDQGLWKDV
to be placed so that its own cable come out from the side that is turned to the front of the car (as shown in the picture beside Fig.14) .
/D\ WKH *36 DQWHQQD FDEOH IURP WKH DQWHQQD WR WKH DUHD EHKLQG WKH PXOWLPHGLD V\VWHP 5ROO XS WKH H[FHVV
19.
FDEOHDQG¿[WKHFDEOHDWWKHGDVKERDUGZLULQJKDUQHVVXVLQJWKHFODPSVXSSOLHGZLWKWKHNLW

Page 1626 of 1659


L714 79 74 05
1
Fig.15
2
Fig.17
Q
)LJ
3
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
Assembly of the microphone of the Bluetooth system.
The Bluetooth function of the Kenwood system can not use the same microphone that is used by the original
bluetooth system of the car. For this reason it is necessary to install a new microphone (supplied inside the
Kenwood package) in the roof lamp; this new microphone has to replace the one that can be present on the car (if it has the Bluetooth opiton).
Lay the cable of the microphone (that is supplied inside the Kenwood package) from the multimedia system (in the
20.
central console of the dashboard) to the roof lamp following the red path that is shown in the picture( Fig.15).
To pass the wiring harness under the roof liner, remove the screw underneath the roof lamp ( 1)LJ) so
that the front part of the roof liner can be lowered and the wire can be passed under it. On the lower part of the door side the wiring harness can be passed under the coverings without removing them ( 2)LJ .
$OZD\V WDNH WKH XWPRVW FDUH QRW WR GDPDJH WKH OHDWKHU XSKROVWHU\ ZKLOH LQVHUWLQJ WKH FDEOH XQGHU WKHJDVNHWVDQGFRYHULQJV
7KH OLWWOH EUDFNHW WKDW LV ¿[HG DW WKH PLFURSKRQH KDV WR EH VWXFN EHWZHHQ WKH URRI ODPS DQG URRI OLQHU WKH
21.
microphone has to be placed turned to the driver headrest in the position that is shown in the picture beside (3)LJ ).
Assembly of the new iPod and USB connection.
Drill a hole of 20 mm of diameter
22. 4)LJ EHKLQGWKHJORYHER[RIWKHSDVVHQJHUVLGH,I\RXVHHWKHJORYHER[
IURPEHKLQGWKHKROHPXVWEHLQWKHULJKWVLGHRIYHUWLFDOSRVWHULRUZDOORIJORYHER[WKHULJKWSRVLWLRQLVZKHUH
WKHUHLVWKH³WULDQJXODU´GHSUHVVLRQRQWKHJORYHER[¶ZDOO )LJ
If the car is equipped with the iPod interface as original optional, this hole is already present and it is not necessary to be done again.
On the cable for the iPod’s connection, assemble one of the black clamp that are supplied in the kit. This black
23.
FODPSPXVWEH¿[HGDWPPIURPWKHFRQQHFWRUWKDWZLOOEHFRQQHFWHGWRWKHL3RG
5HSHDWWKHVDPHRSHUDWLRQRQWKHFDEOHRIWKH86%FRQQHFWLRQDVVHPEOLQJDEODFNFODPSDWPPIURPWKH
24.
USB connector.

Page 1627 of 1659

7
L714 79 74 05
)LJ
5S
Fig.19
U
T
Fig.20
Z
9
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
Insert the iPod cable and then the USB cable into the small foam rubber
25. 5)LJ supplied with the kit.
Assemble the small foam rubber
 5)LJ  VXSSOLHGZLWKWKHNLWLQWKHKROHEHKLQGWKHJORYHER[VRWKDWWKH
L3RGDQG86%FRQQHFWLRQVJRLQVLGHWKHJORYHER[LWVHOI
3XOOWKHWZRFDEOHVIURPWKHLQWHUQDOVLGHRIWKHJORYHER[SXOOWLOOWKHEODFNFODPSV DVVHPEOHZLWKWKHRSHUDWLRQ
27.
DQG  6)LJ have arrived to touch the foam rubber on the its esternal side.
Lay the two cables (iPod and USB)

starting from the small foam rubber 5)LJ to the rear part of the
PXOWLPHGLDV\VWHPVHFXUHLWDORQJWKH$&SLSHXVLQJWKHFODPSVVXSSOLHGZLWKWKHNLW5ROOXSWKHH[FHVVFDEOH
LQVHUWLWLQDVSRQJHVOHHYHDQG¿[WKHZKROHXVLQJ
a clamp.
Assembly of the iPod brackets
$V VKRZQ LQ WKH ¿JXUH Fig.19  WZR EUDFNHWV DUH SUHVHQW LQ WKH NLW WKH ¿UVW 7)LJ) useful for the iPod
Nano, the second ( 8)LJ) useful for iPod of 80gb and the all other using the proper support. These
EUDFNHWVPXVWEH¿[HGLQWKHLQWHUQDOVLGHRIWKHJORYHER[FRYHU7KLVRSHUDWLRQLVQRWQHFHVVDU\LIWKHFDULV
equipped with the iPod connection as original equipment.
The picture (
29. Fig.19 ) show the right position of the two iPod’s brackets. Position the brackets and drill two little
KROH WZR IRU HDFK EUDFNHW  ZKHUH WKHUH DUH WKH EUDFNHWV¶ ¿[LQJ SRLQWV WKDW LV WKH KROH ZKHUH LW LV QHFFHVVDU\
LQVHUWWKHVFUHZVWR¿[WKHEDFNHW 
:KLOH\RXGULOOWKHLQWHUQDOVLGHRIJORYHER[¶FRYHU\RXPXVWEHHVSHFLDOO\FDUHIXOLQRUGHUWRGRQ¶W
GDPDJHWKHIURQWDOVLGHRIWKHJORYHER[DUHODSDUWHIURQWDOHGHOORVSRUWHOORVWHVVR)RUWKLVUHDVRQ
WKHKROHPXVWEHVKDOORZFRQVHTXHQWO\\RXPXVWGULOORQO\WKHLQWHUQDOVLGHRIWKHJORYHER[DQG\RX
PXVWGRQ¶WWRXFKWKHIURQWSDUWRIWKHFRYHU
Using the little screws supplied with the kit and the hole, assembly the iPod’s brackets on the internal side of the
30.
JORYHER[¶FRYHU
Assembly of the new Kenwood multimedia system.
‡Assemble the dashboard ±UHIHUHQFH6
As shown in the picture beside (
31. Fig.20 ), using the screw and the washer supplied with the kit, assemble the
black stud ( 9)LJ) that is supplied with the kit in the hole ( =)LJ) that is present behind the Kenwood
multimedia system.

Page 1628 of 1659


L714 79 74 05
I
3
2
4
II
1
IIIVIII
IX
5
IV
V
VIVIIX
Fig.21
7
9

10
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
The table down here show all the connections that have to be carry out behind the Kenwood multimedia system. 32.
Each line is equivalent to a connection that have to be done between the two connector that are shown on the
line itself. All the involved connectors are shown in the picture beside
(Fig.21 WKH\DUHLGHQWL¿HGE\DQXPEHU
FODVVLFRUURPDQ DQGE\DFRORUWKHWZRFRQQHFWRUVLGHQWL¿HGE\WKHVDPHQXPEHUDQGWKHVDPHFRORUKDYH
to be connected together.
The white connector (I Fig.21 KDVFRQQHFWLRQSRLQWVZLWKRQHFDEOHHDFKWKH¿UVWFDEOHKDVDELJGLDPHWHU
while the other one is lesser thick. The green connector (
1Fig.21 ) has to be connect to the connection point
ZKHUHWKHUHLVWKHELJJHVWFDEOHLQWKLVFRQQHFWLRQSRLQWWKHUHDUHWZROLWWOHKRRNVWKDW¿[WKHMRLQLQJEHWZHHQ
the two connectors.
If the car is equipped with rear view camera: behind the new Kenwood multimedia system, verify that there
is the connection between the video jack of the rear view camera (multimedia harness) and the connection of the Kenwood system; this connection had to be carried out with the operation 2 at page 4 (B )LJ 11).
N° Descri pti on N° Descri pti on
1Radio antenna connector - antenna side >IRadio antenna wiring harness connector
2CAN line connector - car side>IIRNS-E main connector
N° Descri zi one
3Radio antenna connector - system side>IIIRadio antenna connection
4CAN line connector - system side>IVMain Kenwood connection
N° Descri pti on
5GPS antenna connector>VGPS antenna connection
iPod video jack (yellow)>VIiPod video connection (yellow)
7iPod audio jack (black)
>VIIiPod audio connection (black)
iPod USB connector>VIIIUSB connection iPod (see the label on the cable)
9USB connector>IXUSB connection
10Microphone jack (Bluetooth system) >XMicrophone plug (Bluetooth system)
Inte rfa ce w iring ha rne ss
.H QZ RRGPXOWLPH GLD V\VWH P
Acce ssorie s conne ctions
Ca r's w iring ha rne ss

Page 1629 of 1659

9
L714 79 74 05
Fig.22
AB
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
Place the new Kenwood multimedia system (
33. $)LJ) in the central console of the dashboard and insert it in the
VSHFL¿FEUDFNHWDQGVOLGHWKDWDUHDVVHPEOHGZLWKWKHSUHYLRXVRSHUDWLRQV RSHUDWLRQVIURPWR 
)L[ WKH QHZ VSHFL¿F IUDPH
34. %)LJ) that is supplied with the kit on the central console around the Kenwood
system ( $)LJ 7RFDUU\RXWWKLVRSHUDWLRQLWLVQHFHVVDU\WR¿WWKHWZRVWXGWKDWDUH¿[HGEHKLQGWKHIUDPHLQ
the hole that are present in the supportion bracket.
Vehicle setting up.
 7KHFDU¶VSUHYLRXV]LS¿OHFDQQRWEHXVHGWRVHWXSWKHV\VWHPRIWKHFDU2QO\DIWHUWKH6SDUH3DUWV 6DOHV2I¿FHKDVFRQ¿UPHGWKH]LS¿OH¶VXSGDWLQJIRUWKHFDULQTXHVWLRQFDQWKH.RPELLQVWUXPHQW FOXVWHU (&8 EHVHWXSZLWKWKHQHZ]LS¿OH
8VLQJWKH/D5DV\VWHPGRZQORDGWKHQHZ]LS¿OHDVVRFLDWHGZLWKWKHFDU¶V9,1
35.  .
8VLQJWKHQHZ]LS¿OHDQGWKH/D5D$6V\VWHPVHWXSWKH.RPELLQVWUXPHQWFOXVWHU (&8 
  .
Final operations ‡ Assemble the central tunnel  – reference C) .
‡ Assemble the new (supplied with the kit) bench behind the seats – reference B)
‡ )L[ GRQ¶WUHPRYH WKHIURQWSDUWRIWKHURRIOLQHU ±ULIHULPHQWR: .
‡ Assemble the roof lamp  .
‡ Assemble the passenger sun visors  ±UHIHUHQFH:operations 5-6).
‡ Assemble the passenger side lower dashboard assembly UHIHUHQFH5 .

Page 1630 of 1659

1
L714 79 75 05
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
7KLVVHFWLRQH[SODLQVKRZWRDVVHPEOH
$  5HDUYLHZFDPHUDNLW
%  6DWHOOLWHQDYLJDWLRQNLW
&  %OXHWRRWK.LW,QVWDOODWLRQ

Page:   < prev 1-10 ... 1581-1590 1591-1600 1601-1610 1611-1620 1621-1630 1631-1640 1641-1650 1651-1660 1660 next >