remote start LAMBORGHINI GALLARDO 2009 Workshop Manual

Page 1274 of 1659

2
L714 09 15 00
Fig.2
A - +
%
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
&RQQHFWWKHSRVLWLYHSROHVWRWKHSRVLWLYHFDEOH UHG  •Secure one end to the positive pole  of the dead battery ( A-Fig.2).
• Secure the other end to the positive pole  of the supply battery ( %)LJ).
&RQQHFWWKHQHJDWLYHSROHVWRWKHQHJDWLYHFDEOH EODFN  • Secure one end to the negative pole  of the supply battery ( %)LJ).
• Secure the other end to the negative pole  of the supply battery ( A-Fig.2).
Starting the engine • Start the engine of the car that is supplying the current and let it idle.
• Start the engine of the car with the dead battery.
1RWH
The battery’s low voltage could require resynchronization of the ignition key before starting. In this case, turn the key to ON and hold the LOCK/UNLOCK buttons down for approximately 30 seconds.
• If the engine does not start immediately, stop starting after 10 seconds and repeat after approximately 30
seconds.
• Leave the engine on and remove the cables in the opposite order described previously (remove the ground
FRQQHFWLRQ¿UVWDQGWKHQWKHSRVLWLYH 
• Carry out the following operations:Resynchronization of second remote control Resynchronization of steering angle Resynchronization of power window zero position

Page 1532 of 1659

96
L714 10 90 00
Fig.82 Fig.83A
A
® Automobili Lamborghini S.p.A.7KHLQIRUPDWLRQDQGSURFHGXUHVSXEOLVKHGEHORZDUHVWULFWO\FRQ¿GHQWLDODQGH[FOXVLYHO\IRUWKH/DPERUJKLQL'HDOHU1HWZRUNDQG$XWKRUL]HG6HUYLFH3RLQWV$OOFRS\ULJKWVDUHSURSHUW\RI$XWRPRELOL
/DPERUJKLQL6S$EDVHGRQFRS\ULJKWODZ$OORIWKH3')FKDSWHUVLQWKH:(%ZRUNVKRSPDQXDOVGHVFULEHGEHORZDUHEDVHGRQLQIRUPDWLRQDYDLODEOHDWWKHWLPHRISXEOLFDWLRQ7KHFRPSDQ\UHVHUYHV
WKH ULJKW WR PDNH XSGDWHV DQG PRGL¿FDWLRQV 7KH IROORZLQJ DUH SURKLELWHG UHSULQWLQJ UHSURGXFWLRQIRUZDUGLQJ WR XQDXWKRUL]HG SHRSOH DQGRU WKLUG SDUWLHV DQG WUDQVODWLRQ LQFOXGLQJ SDUWLDO ZLWKRXW
ZULWWHQDXWKRUL]DWLRQIURP$XWRPRELOL/DPERUJKLQL6S$
7RVHWXSWKH=.(FRQWUROXQLWVHOHFWWKHUHODWLYH¿HOGDQGFOLFN³6HW8S´ $)LJ .
To codify the ZKE control unit, carry out the basic settings on the frequencies used in the country of destination and the keys featuring the remote control to open and close the doors.
The setup wizard for the ZKE control unit is the following:
- Press “OK” to start (A-Fig.83).