turn signal LAND ROVER DEFENDER 1999 User Guide

86ELECTRICAL
6
DESCRIPTION AND OPERATION Volumetric Sensor
The volumetric sensor is located behind the RH’B’post on 90/110 station wagon models, on the headlining
between the interior lamp and rear view mirror on 90/110 pick-up models and on the headlining above the RH
door on 130 crewcab models.
The volumetric sensor operates by emitting a signal, which is received back to the sensor as it bounces back from
objects inside the vehicle. Once armed, the sensor will detect a disturbance to the returned waves. This is sensed
by the anti-theft alarm ECU which activates the alarm sounder or BBUS.
ProCarManuals.com

ELECTRICAL
13
DESCRIPTION AND OPERATION Passive Immobilisation
Passive immobilisation occurs when the key is removed from the ignition switch and the drivers door is opened,
after a period of 30 seconds the engine will become immobilised. If the ignition is turned off or the key is removed
from the ignition switch and drivers door is not opened, the engine will become immobilised after 5 minutes.
The passive immobilisation system operates in conjunction with the transponder coil located around the ignition
switch barrel. The transponder coil emits an electro magnetic waveform signal which excites the remote handset
into transmitting a remobilisation signal. When remobilisation is requested, the anti-theft alarm ECU transmits an
appropriate code to the ECM on Td5 models or the engine immobilisation ECU on 300Tdi models.
Active immobilisation
Active immobilisation is only invoked when the vehicle is locked using the remote handset. Active immobilisation
performs the same engine disable functionality as the passive immobilisation previously described, but includes
full CDL and activation of perimetric and volumetric alarm modes.
ProCarManuals.com

86ELECTRICAL
14
DESCRIPTION AND OPERATION Emergency Key Access (EKA)
If the vehicle is in an immobilised condition and the remote handset is not available or inoperable, an EKA
procedure using the vehicle key is available to remobilise the engine systems. The EKA code is supplied with the
vehicle and is shown on the security card supplied with the owners handbook.
NOTE: This feature is only available in markets where full alarm functionality is specified.
The EKA code involves the input of a unique four digit code which is entered using the ignition switch and the
drivers door switch. Note that the alarm sounder will operate as soon as the drivers door is opened and will
continue until the sequence is successfully completed.
To enter the code (2, 3, 4, 5 for example) perform the following steps:
1.Remove the handset from the key ring and position the handset well away from the ignition switch when
entering the code.
2.Open the driver’s door and immediately insert the key in the ignition switch and turn the ignition switch to
position II. Hold this position until the alarm sounds, then switch the ignition off (position 0) and close the
driver’s door.
3.Enter the first digit of the code. Turn the ignition on (to position II) and then off twice. Open and close the
driver’s door to enter the first digit.
4.Enter the second digit. Turn the ignition on and then off, three times. Open and close the driver’s door to
enter the second digit.
5.Enter the third digit. Turn the ignition on and then off, four times. Open and close the driver’s door to enter
the third digit.
6.Enter the fourth digit. Turn the ignition on and then off, five times. Open and close the driver’s door to enter
the fourth digit. If the code has been entered correctly, the alarm LED in the instrument pack will extinguish
and the engine can be started after the last closure of the driver’s door.
If a digit is incorrectly entered, holding the ignition switch in the on position for more than 5 seconds will reset the
sequence. The code must then be re-entered from the beginning.
If the EKA code is correctly entered, the security LED will illuminate for 1 second, the immobilisation will be
disabled and the alarm sounder will cease to operate.
If the EKA code is incorrectly entered, the alarm sounder will sound twice and the correct code must be
re-entered, If the EKA code is incorrectly entered three times the system invokes a 30 minute lockout. This is
signalled by the LED flashing with a long illuminated period followed by a short extinguished period for the lockout
duration.
NOTE: Disabling the alarm and immobilisation system using the EKA procedure is only valid for
one ignition on/off cycle. When the ignition is switched off, the immobilisation system will be
activated after a period of 30 seconds. If the remote handset is still unavailable, the EKA
procedure will have to be repeated each time the vehicle is to be driven.
ProCarManuals.com