ESP LAND ROVER DISCOVERY 1995 Owner's Guide

Page 810 of 873

ELECTRICAL
7
DESCRIPTION AND OPERATION ANTI-THEFT ALARM DESCRIPTION (96 MODELS)
NOTE: The alarm system provides security
protection under wide ranging
circumstances and is fully programmable
to meet market requirements; consequently some
of the features listed will vary dependent on
vehicle model or territory.
The handset is intended to be the primary source of
control for the alarm system. The key should only be
used in the event of handset failure or if perimetric
arming only is required.
Immobilisation
After a time period the vehicle is automatically
immobilised regardless of whether or not the alarm is
armed.
Mobilisation
The handset provides the normal means of
mobilisation. In the event of handset failure, the key
may be used to enter the emergency key access
code.
Perimetric arming
Provides protection whilst the vehicle is still occupied.
Volumetric arming
If movement within the vehicle is detected the alarm
will be triggered.
NOTE: Perimetric arming always
accompanies volumetric arming.
Built-in test
The alarm system has a built-in test procedure, but if
possible any fault finding should normally be
undertaken using TestBook.
Emergency key access (EKA)
In the event of handset failure the alarm can be
disarmed by entry of the EKA code which is unique to
each vehicle.CONTROL SYSTEM
Electronic control unit (ECU) and relays
The ECU is the alarm system 'brain' and controls all
alarm functions. It responds to inputs received, by
supplying suitable outputs to indicate the status of the
alarm system or activating the relevant warning
devices.
Handset
The handset is the primary source of control for the
alarm system i.e. it locks and unlocks the vehicle,
arms and disarms the alarm.
Door key
The vehicle may be locked using the key (perimetric
arming only).
NOTE: The vehicle MUST be unlocked
using the handset. The key may be used to
unlock the vehicle if the handset fails to
operate, see operation, Emergency key access.
Passive coil
The passive coil is located around the starter switch
and triggers the handset (usually located on the
keyring) if it is within close proximity.
Aerial
The aerial is a floating connection which supplies the
alarm ECU with the signal received from the handset.
Immobilisation unit (spider)
Dependent on model or territory, the system may be
fitted with an immobilisation unit which is discreetly
located and provides an interface between the ECU
and immobilised areas of the vehicle.

Page 813 of 873

86ELECTRICAL
10
DESCRIPTION AND OPERATION Radio frequency system
The RF system uses frequencies according to market
and both ECU and handset are colour coded:
Territory ECU/Handset............................... Frequency..................
Europe Blue/Blue.................................. 433.92 MHz.........................
NAS Green/Green....................................... 315.00 MHz....................
Japan Green/Green.................................... 315.00 MHz....................
Gulf Green/Green....................................... 315.00 MHz....................
Rest of World Green/Brown........................ 315.00 MHz...................
NOTE: In service NAS, Japan and Gulf will
have the handset changed to brown.
Passive coil
The passive coil excites a receiving coil in the handset
causing it to automatically transmit a remobilisation
signal to the ECU.
Inertia switch and central door locking
Actuation of the inertia switch will cause the doors to
be unlocked. A time-out period (programmable
between 0-5 minutes) will ensue, during which all CDL
and alarm activity is disabled.
NOTE: This feature only applies when the
starter switch is in the on position.
Handset
Under normal circumstances pressing the respective
buttons on the handset once, will unlock or lock the
vehicle. If operating the handset does not achieve the
desired effect
See Repair, Handset.
Functional detail
For full functional details and circuit diagrams
See
Electrical Trouble Shooting Manual..
Vehicle traceability
All Land Rover vehicles are fitted with a multitude of
discreet security features to prevent theft or assist
recovery in the event of a vehicle being stolen. All
vehicles are traceable, since it is impossible to
remove all security identification.

Page 863 of 873

ELECTRICAL
43
REPAIR ANTI-THEFT ALARM ECU (96 MODELS)
Service repair no - 86.55.85
Remove
1.Remove 4 studs securing fascia left hand
closing panel.
2.Remove closing panel.
3.Disconnect 2 multiplugs from ECU.
4.Remove nut securing ECU/relay bracket.
5.Lower bracket.
6.Remove 2 nuts securing ECU to bracket.
7.Remove ECU.
NOTE: A new ECU must be initialised
using TestBook.
Refit
8.Reverse removal procedure.HANDSET (96 MODELS)
If vehicle does not respond to handset immediately, it
may have lost synchronisation. To re-synchronise,
press either button, 4 times in quick succession. If
handset still fails to respond, check batteries, refer to
Owner's handbook. If batteries are okay, it may be
necessary to use emergency key access, refer to
Owner's handbook.
NOTE: New handsets must be initialised
using TestBook.
PASSIVE COIL (96 MODELS)
Service repair no - 86.77.35
Remove
1.Remove steering column shroud.
See
STEERING, Repair, Steering column shroud
2.Release multiplug from harness clip and
disconnect.
3.Release passive coil from starter switch.
4.Remove bulb holder/starter switch shroud.
5.Remove coil.
Refit
6.Fit coil, ensuring switch illumination bulb harness
passes through large cut-out.
7.Secure coil with cable tie.
8.Position bulb holder/starter switch shroud and
locate bulb.
9.Locate bulb holder/starter switch shroud,
ensuring cut-out in shroud aligns with lug on
starter switch.
10.Connect multiplug and secure to clip.
11.Fit column shroud.

Page:   < prev 1-10 11-20 21-30 31-40