Lexus CT200h 2014 Owner's Manual (in English)

4917-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
XVehicles with LED headlights
■Rear
Halogen front fog light
(if equipped)
Headlight high beam Front turn signal light1
2
3
Rear fog light (left-hand drive
vehicles) or back-up light
Rear fog light (right-hand drive
vehicles) or back-up lightRear turn signal light
Outer foot light1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 491 Friday, May 30, 2014 1
1:14 AM

4927-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
■Headlight low beams (halogen headlights)Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight low
beams on once and visually confirm
that no light is leaking through the
mounting.
Replacing light bulbs
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 492 Friday, May 30, 2014 1 1:14 AM

4937-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
■Headlight high beams (halogen headlights) For the right side only: Move the
washer fluid filler opening.
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 493 Friday, May 30, 2014 1 1:14 AM

4947-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight high
beams on once and visually confirm
that no light is leaking through the
mounting.
For the right side only: Reinstall the washer fluid filler opening.
■Headlight high beams (LED headlights)Turn the cover counterclockwise
and remove it.
Turn the bulb base counterclock-
wise.
Unplug the connector while pull-
ing the lock release.
5
6
1
2
3
CT200h_OM_OM76135E_(EE).book Page 494 Friday, May 30, 2014 1 1:14 AM

4957-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb with
the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check
that it is not loose, turn the headlight
high beams on once and visually
confirm that no light is leaking
through the mounting.
When installing the cover, conduct step in reverse.
■Halogen front fog light (if equipped) Remove 2 screws, a bolt and clip,
and pull down the fender liner.
Pull the fender liner down slowly,
being careful not to dislodge any
fixed components.
4
5
61
1
CT200h_OM_OM76135E_(EE).book Page 495 Friday, May 30, 2014 1 1:14 AM

4967-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the fog lights on once
and visually confirm that no light is
leaking through the mounting.
2
3
4
5
CT200h_OM_OM76135E_(EE).book Page 496 Friday, May 30, 2014 11:14 AM

4977-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
Reinstall the fender liner with 2
screws, a bolt and clip.
■Front turn signal light s (halogen headlights)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
■Front turn signal lights (LED headlights)
XLeft side
Remove the power control unit
cover.
6
1
2
3
1
CT200h_OM_OM76135E_(EE).book Page 497 Friday, May 30, 2014 1 1:14 AM

4987-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
XRight side
Move the washer fluid filler opening. (→P. 4 9 3 )
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
2
3
4
1
2
3
4
CT200h_OM_OM76135E_(EE).book Page 498 Friday, May 30, 2014 1 1:14 AM

4997-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
7
Maintenance and care
■Rear turn signal lights Open the back door and remove
the covers and bolts, and remove
the lamp assembly by pulling it
directly backward from the rear
of the vehicle.
Use a flathead screwdriver wrapped
in a cloth.
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
■Back-up light/rear fog lightOpen the back door and remove
the cover.
Use a flathead screwdriver wrapped
in a cloth.
1
2
3
4
1
CT200h_OM_OM76135E_(EE).book Page 499 Friday, May 30, 2014 1 1:14 AM

5007-3. Do-it-yourself maintenance
CT200h_OM_OM76135E_(EE)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
When installing, reverse the steps listed.
The illustrations show the removal of a back-up light from a right-hand drive
vehicle.
■Outer foot lights
Press the upper part of the out-
side rear view mirror to tilt the
mirror face upward, and apply
protective tape to the lower part
of the mirror cover.
Insert 2 flathead screwdrivers
wrapped in protective tape, and
disconnect the tabs behind the
mirror.
Pry the mirror out toward you, dis-
connecting the tabs 2 at a time.
Work carefully, ensuring that you do
not drop the mirror.
2
3
4
1
2
CT200h_OM_OM76135E_(EE).book Page 500 Friday, May 30, 2014 1 1:14 AM