radiator cap LEXUS ES300 2005 Repair Manual

550DB-02
I03839
Push
SSTPull
Release
Lever
I06919
Screw
Driver Disconnect the
tube using hand
I31522
- HEATER & AIR CONDITIONERAIR CONDITIONING RADIATOR ASSY
55-17
2632 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OVERHAUL
HINT:
COMPONENTS: See page 55-15
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page 55-8)
SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070,
07117-88080)
2. DISCONNECT COOLER REFRIGERANT SUCTION
HOSE NO.1
(a) Install SST to piping clamp.
SST 09870-00015
HINT:
Confirm the direction of the piping clamp claw and SST using
the illustration showing on the caution label.
(b) Push down SST and release the clamp lock.
NOTICE:
Be careful not to deform the tube, when pushing SST.
(c) Pull SST slightly and push the release lever, then remove
the piping clamp with SST.
(d) Disconnect the cooler refrigerant suction hose No. 1.
NOTICE:

Do not use tools like screwdriver to remove the tube.

Cap the open fittings immediately to keep moisture or
dirt out of the system.
3. DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
SST 09870-00025
HINT:
Disconnect cooler refrigerant liquid pipe A in the same way as the cooler refrigerant suction hose No. 1.
4. DISCONNECT HEATER OUTLET WATER HOSE
(a) Using pliers, grip the claws of clip and slide the clip and
disconnect the heater outlet water hose.

I31770
I31771
I31563Clamp 55-22
- HEATER & AIR CONDITIONERAIR CONDITIONING RADIATOR ASSY
2637 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(b) Remove the 3 nuts, disconnect the 3 earth wires.
(c) Remove the 3 caps, 7 bolts and instrument panel rein-
forcement.
20. REMOVE BLOWER ASSY
(a) Disconnect the connectors.
(b) Remove the screw, clamp and blower connector holder.

I31509
I317726 Clamps
I31563Clamp
I31771
(A) 55-28
- HEATER & AIR CONDITIONERAIR CONDITIONING RADIATOR ASSY
2643 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
35. INSTALL BLOWER ASSY
(a) Install the blower assy with the 2 screws and 2 nuts.
Torque: 1.5 NVm (15 kgfVcm, 12 in.Vlbf)
(b) Install the 6 clamps, connect the wire harness.
(c) Install the blower connector holder with the screw.
(d) Connect the connectors.
36. INSTALL INSTRUMENT PANEL REINFORCEMENT
(a) Install the instrument panel reinforcement with the 7 bolts
and 3 caps.
Torque: 20 NVm (203 kgfVcm, 14 ftVlbf) (Bolt A)

550DH-02
I31635
Radiator Support Upper
O-ring

Cooler Condenser Assy
Cooler Dryer
Filter
Cap
9.8 (100, 85 in.Vlbf)
Non-reusable parts Compressor oil ND-OIL 8 or equivalent
9.8 (100, 85 in.Vlbf)
O-ring
5.4 (55, 47 in.Vlbf)
O-ring

12 (125, 9)


Air Cleaner Inlet No. 1
Air Cleaner Inlet Assy
NVm (kgfVcm, ftVlbf): Specified torque
Radiator Lower Air Deflector
Hood Lock Release Lever
Protector
55-44
- HEATER & AIR CONDITIONERCOOLER CONDENSER ASSY
2659 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
COMPONENTS

141J7-02
A78541
(b)
(b)
(b)(a)
(a)
A36719
P18805
- ENGINE MECHANICALVALVE CLEARANCE (3MZ-FE)
14-7
2099 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
VALVE CLEARANCE (3MZ-FE)
ADJUSTMENT
1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. DRAIN ENGINE COOLANT (See page 16-9)
3. REMOVE FRONT FENDER APRON SEAL RH
4. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
5. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
6. REMOVE AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
7. REMOVE EMISSION CONTROL VALVE SET (See page 11-13)
8. REMOVE INTAKE AIR SURGE TANK (See page 11-13)
9. REMOVE RADIATOR HOSE INLET
10. REMOVE IGNITION COIL ASSY
11. REMOVE CYLINDER HEAD COVER SUB-ASSY
(a) Remove the 2 engine wire harness clamps.
(b) Remove the 3 nuts, then disconnect the engine wire har-
ness.
(c) Remove the 9 bolts and cylinder head cover.
12. REMOVE CYLINDER HEAD COVER SUB-ASSY LH
(a) Using an E6 Torx) socket wrench, remove the 2 bolts and
disconnect the engine wire harness protector.
(b) Remove the 9 bolts and cylinder head cover.
13. INSPECT VALVE CLEARANCE
(a) Turn the crankshaft pulley, then align the timing notch with
the timing mark º0º of the timing belt No. 1 cover.
(b) Check that the valve lifters on the intake side of the No.
1 cylinder are not pushed by the cam.
If the valve lifters are pushed, turn the crankshaft by 1 revolution
(360) and align the marks as above.

A78386
8.0 (80, 71 in.Vlbf)
Ignition Coil Assy
Cylinder Head Cover
Sub-assy LH
8.4 (85, 74 in.Vlbf)
Engine Wire
Cylinder Head Cover Gasket No. 2
Camshaft Bearing Cap No. 2
16 (163, 12)
Camshaft Bearing Cap No. 2Camshaft Bearing Cap No. 3
Camshaft Bearing Cap No. 6
Camshaft Bearing Cap No. 5
Camshaft Timing Gear Assy
Camshaft Bearing Cap No. 4
Camshaft Timing Gear
Bolt WasherCamshaft Sub Gear
Wave Washer
Camshaft Sub GearCamshaft Sub Gear
Shaft Snap Ring
Camshaft Bearing Cap No. 2
150 (1,530, 111)
16 (163, 12)
Camshaft Bearing Cap No. 1
No. 4 Camshaft Sub-assy
Radiator Hose Inlet
N´m (kgf´cm, ft´lbf)
: Specified torque

Non-reusable part
Camshaft Setting
Oil Seal

V-bank Cover Sub-assy
8.0 (80, 71 in.Vlbf)
7.9 (81, 70 in.Vlbf)
No. 3 Camshaft
Sub-assy
x3
x9
x10
x10 14-106
- ENGINE MECHANICALCAMSHAFT (LH BANK) (3MZ-FE)
2198 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

141JI-01
A84919N´m (kgf´cm, ft´lbf) : Specified torque
7.9 (81, 70 in.Vlbf)x3
V-bank Cover Sub-assy
Mass Air Flow
Meter Connector Fuel Vapor Feed
Hose No. 1Vacuum Hose
Air Cleaner Cap
Sub-assy
Air Cleaner Filter
Element Sub-assy
5.0 (51, 44 in.Vlbf)
W/O TEMS:
Front Suspension Upper Brace Center
80 (816, 59)
Spacer
x2
80 (816, 59)
x2
Spacer
Vacuum Hose
Clip x7
Radiator Lower
Air DeflectorClipAir Cleaner
Inlet Assy
5.0 (51, 44 in.Vlbf)x2
VSV Connector
Air Cleaner Casex3
5.0 (51, 44 in.Vlbf)
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
14-125
2217 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
CYLINDER HEAD GASKET NO.2 (3MZ-FE)
COMPONENTS

141JJ-01
A86574
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
14-133
2225 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11-1)
2. DISCONNECT BATTERY NEGATIVE TERMINAL
3. DRAIN ENGINE COOLANT (See page 16-9)
4. DRAIN ENGINE OIL (See page 17-20)
5. REMOVE FRONT WHEEL RH
6. REMOVE RADIATOR LOWER AIR DEFLECTOR (See page 19-5)
7. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
8. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
9. REMOVE AIR CLEANER INLET ASSY (See page 19-5)
10. REMOVE AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
11. REMOVE AIR CLEANER CASE (See page 19-5)
12. REMOVE EMISSION CONTROL VALVE SET (See page 11-13)
13. REMOVE INTAKE AIR SURGE TANK (See page 11-13)
14. REMOVE INTAKE MANIFOLD (See page 10-16)
15. REMOVE WATER OUTLET (See page 10-16)
16. REMOVE FRONT FENDER APRON SEAL RH
17. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
18. REMOVE VANE PUMP V BELT (See page 14-5)
19. REMOVE ENGINE MOVING CONTROL ROD (See page 14-79)
20. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
21. REMOVE GENERATOR BRACKET NO.2 (See page 14-79)
22. REMOVE CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021, 09950-50013 (09951-05010, 09952-05010,
09953-05020, 09954-05031)
23. REMOVE TIMING BELT NO.1 COVER
24. REMOVE TIMING BELT NO.2 COVER (See page 14-79)
25. REMOVE ENGINE MOUNTING BRACKET RH (See page 14-79)
26. REMOVE TIMING BELT GUIDE NO.2
27. REMOVE TIMING BELT (See page 14-79)
28. REMOVE TIMING BELT IDLER SUB-ASSY NO.2
29. REMOVE CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
30. REMOVE TIMING BELT NO.3 COVER (See page 14-93)
31. REMOVE MANIFOLD STAY NO.2 (See page 14-29)
32. SEPARATE EXHAUST PIPE ASSY FRONT (See page 15-2)
33. REMOVE OIL LEVEL GAGE GUIDE
(a) Remove the bolt which secures the oil level gage guide
from the cylinder head LH.
(b) Pull out the oil level gage guide and oil level gage together
from the cylinder block.
(c) Remove the O-ring from the oil level gage guide.

100J5-01
A86250
A86251
(a)(a)
(a)
(b) 2 Retainers
Socket Hexagon
Wrench 5
A86252
(a)
(b)
(d)
(e)
(b)
(b)
(b)
(c)
(d)
(e)
(f)
A86253
(a)
(c) (b)
- ENGINE CONTROL SYSTEMTHROTTLE BODY ASSY (3MZ-FE)
10-1 1
2016 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DISCONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
2. REMOVE RADIATOR LOWER AIR DEFLECTOR (See page 19-5)
3. DRAIN ENGINE COOLANT (See page 19-5)
4. REMOVE FRONT SUSPENSION UPPER BRACE
CENTER (W/O TEMS)
(a) Remove the 4 nuts, then remove the front suspension up-
per brace center and 4 spacers.
(b) Temporarily tighten the 4 nuts.
5. REMOVE V-BANK COVER SUB-ASSY
(a) Using a socket hexagon wrench 5, remove the 3 nuts.
(b) Unfasten the 2 retainers, then remove the V-bank cover.
6. REMOVE AIR CLEANER CAP SUB-ASSY
(a) Disconnect the mass air flow meter connector.
(b) Disconnect the 4 vacuum hoses.
(c) Disconnect the ventilation hose No. 2.
(d) Disconnect the fuel vapor feed hose from the 2 hose
clamps.
(e) Loosen the 2 air cleaner cap bolts.
(f) Loosen the air cleaner hose clamp bolt, then remove the
air cleaner cap.
(g) Remove the air cleaner filter element.
7. REMOVE THROTTLE BODY ASSY
(a) Disconnect the throttle motor connector.
(b) Disconnect the water by-pass hose No. 2.
(c) Disconnect the water by-pass hose No. 3.

A86254
(d)
(d)
(d)
(d) 10-12
- ENGINE CONTROL SYSTEMTHROTTLE BODY ASSY (3MZ-FE)
2017 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) Remove the 4 bolts, then remove the throttle body.
(e) Remove the gasket from the intake air connector.
8. INSTALL THROTTLE BODY ASSY
(a) Install a new gasket to the intake air connector.
(b) Install the throttle body with the 4 bolts.
Torque: 11 NVm (112 kgfVcm, 8 ftVlbf)
(c) Connect the water by-pass hose No. 3.
(d) Connect the water by-pass hose No. 2.
(e) Connect the throttle motor connector.
9. INSTALL AIR CLEANER CAP SUB-ASSY
Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
10. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
11. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
12. ADD ENGINE COOLANT (See page 16-9)
13. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
14. INSTALL V-BANK COVER SUB-ASSY
(a) Fit the 2 retainers, then install the V-bank cover.
(b) Using a socket hexagon wrench 5, tighten the 3 nuts.
Torque: 7.9 NVm (81 kgfVcm, 70 in.Vlbf)
15. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS)
Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)
16. INSTALL RADIATOR LOWER AIR DEFLECTOR
17. SYSTEM INITIALIZATION (See page 19-15)