ignition Lexus ES300h 2014 Navigation Manual

4
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
■INFORMATION FOR HYBRID VEHICL ES IS WRITTEN IN BRACKETS
NEXT TO THE INFORMATIO N FOR GASOLINE VEHICLES
Different writing styles for gasoline and hybrid vehicles
X Example
When the “START STOP ENGINE”
*1 <“POWER”> *2 switch is in ACCESSORY or
IGNITION ON
*1 <ON>*2 mode, the initial screen will be displayed and the system
will begin operating.
*
1: Gasoline vehicle
*
2: Hybrid vehicle
HOW TO READ THIS MANUAL
No.NameDescription
Operational
OutlinesAn outline of the operation is explained.
Main OperationsThe steps of an operation are explained.
Related OperationsA main operation’s supplement ary operations are described.
InformationUseful information for the user is described.

32
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1. BASIC INFORMATION BEFORE OPERATION
1. INITIAL SCREEN
1When the “START STOP ENGINE”
<“POWER”> switch is in ACCESSORY
or IGNITION ON <ON> mode, the ini-
tial screen will be displayed and the sys-
tem will begin operating.
z After a few seconds, the “CAUTION”
screen will be displayed.
z After about 5 seconds, the “CAUTION”
screen automatically switches to the map
screen. (If a button other than the “MAP/
VOICE” button on the Remote Touch is
pressed, the function’s corresponding
screen will be displayed.)
z Images shown on the initial screen can be
changed to suit individual preferences.
(See page 56.)
CAUTION
●When the vehicle is stopped with the
engine running <the hybrid system oper-
ating>, always apply the parking brake for
safety.
zWhen the navigation system is turned on
in a screen other than the map screen,
the “CAUTION” screen will be displayed
when the screen is changed to the map
screen for the first time after it has been
turned on.
MAINTENANCE
INFORMATION
This system reminds users when to re-
place certain parts or components and
shows dealer information (if registered)
on the screen.
When the vehicle reaches a previously
set driving distance or date specified for
a scheduled maintenance check, the
“Maintenance Remind er” screen will be
displayed when the navigation system is
turned on.
z This screen goes off if the screen is not
operated for several seconds.
z To prevent this screen from being dis-
played again, select “Do Not Display
This Message Again” .
z To register maintenance information, see
“MAINTENANCE” on page 133.

33
1. BASIC INFORMATION BEFORE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
2
BASIC FUNCTION
2. HOW TO USE THE Remote Touch
1Use the Remote Touch knob to select
the desired button on the screen.
2To select the button on the screen, press
the Remote Touch knob. Once a button
has been selected, the screen will
change.
zWhen the pointer moves close to a button,
it will be automatically pulled onto that but-
ton. The strength of this pull can be
adjusted. (See page 60.)
z The pointer will disappear from the screen
if it is not moved for 6 seconds. Operation
of the Remote Touch knob will cause the
pointer to reappear.
z Press the “” button on the Remote Touch
to zoom in on the map screen and the “”
button to zoom out. These buttons can also
be used to scroll up and down on list
screens.
z Press the “MENU” button on the Remote
Touch to set a destination or adjust settings
for the audio/video system, air conditioning
system, etc.
z The map screen can be returned to by
pressing the “MAP/VOICE” button on the
Remote Touch.This navigation system can be operated
by the Remote Touch when the “START
STOP ENGINE” <“POWER”> switch is
in ACCESSORY or IGNITION ON
<ON> mode.
CAUTION
●Do not allow fingers, fingernails or hair to
become caught in the Remote Touch as
this may cause an injury.
●Be careful when touching the Remote
Touch in extreme temperatures as it may
become very hot or cold due to the tem-
perature inside the vehicle.

56
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
■LAYOUT TYPE
X “ABC” type
X “QWERTY” type
CHANGING THE STARTUP
IMAGE
When the “START STOP ENGINE”
<“POWER”> switch is in ACCESSORY
or IGNITION ON <ON> mode, the ini-
tial screen will be displayed.
An image can be copied from a USB
memory and used as the startup image.
(For information regarding the startup
image, see “INITIAL SCREEN” on page
32.)
INFORMATION
●
When saving the images to a USB, name
the folder that the startup image is saved
to “StartupImage” and name the folder
that the screen off image is saved to
“DisplayOffImage”. If these folder names
are not used, the navigation system can-
not download the images. (The folder
names are case sensitive.)
●The images file extension is JPG or
JPEG.
●The images file name, including the file
extension, can be up to 32 characters.
●Image files of 10 MB or less can be saved.
●Up to 3 images can be downloaded.

154
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zFor automatic connection, see “CHANG-
ING “Bluetooth* Power”” on page 202.
z When the “START STOP ENGINE”
<“POWER”> switch is in ACCESSORY or
IGNITION ON <ON> mode, the system
searches for a nearby registered cellular
phone.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
z The system will connect with the phone that
was last connected, if it is nearby.
When “Display Phone Status” is set to
“On” , the connection status is displayed.
(See “Bluetooth
® DEVICE CONNEC-
TION STATUS DISPLAY SETTINGS” on
page 204.)
z This screen appears when the Bluetooth
®
phone is first connected after the “START
STOP ENGINE” <“POWER”> switch is in
ACCESSORY or IGNITION ON <ON>
mode.
CONNECTING A Bluetooth®
PHONE
AUTOMATICALLY
When a phone is registered, auto con-
nection is turned on. Always set it to this
mode and leave the Bluetooth
® phone
in a location where connection can be
established.
INFORMATION
●
It may take time if the phone connection
is carried out during Bluetooth® device
playback.
Depending on the type of Bluetooth
®
phone being connected, it may be neces-
sary to perform additional steps on the
phone.

156
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zIf a Bluetooth® phone is disconnected on
purpose, such as turning it off, this does not
happen. Reconnect the Bluetooth
® phone
manually.
RECONNECTING THE
Bluetooth® PHONE
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth
® network when the “START
STOP ENGINE” <“POWER”> switch is
in ACCESSORY or IGNITION ON
<ON> mode, the system automatically
reconnects the Bluetooth
® phone.
When “Display Phone Status” is set to
“On” , the connection status is displayed.

202
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
5This screen is displayed.
zThe information displays the following
items:
z If it is desirable to ch ange the settings, refer
to the following pages.
z When the settings have been changed,
select “Save” .
■CHANGING “Bluetooth* Power”
When “Bluetooth* Power” is “On” :
The Bluetooth
® device is automatically
connected when the “START STOP EN-
GINE” <“POWER”> switch is in ACCES-
SORY or IGNITION ON <ON> mode.
When “Bluetooth* Power” is “Off” :
The Bluetooth
® device is disconnected,
and the system will not connect to it next
time.
z The “Bluetooth* Power” auto connection
state can be set on or off.
• “On” : The auto connection is turned on.
• “Off ” : The auto connection is turned off.
z The auto connection state cannot be
changed from “On” to “Off ” while driving,
but it can be changed from “Off ” to “On” .
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
Screen button/Screen itemInformation
“Device Name”
This name will be dis-
played on the device
when it is connected. It
can be changed to a de-
sired name.
“Passcode”
The password that was
set when the Bluetooth®
device was registered
can be changed.
Device
AddressThe device address is
unique to each device. It
cannot be changed.
Profiles
The compatibility profile
of the Bluetooth® device
is displayed on the
screen. (See pages 146
and 264.)
CHANGING THE Bluetooth®
SETTINGS
The Bluetooth
® settings can be
changed according to the following pro-
cedures.
The “Bluetooth* Power” display shows
the following state.

204
2. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
■Bluetooth® DEVICE CONNEC-
TION STATUS DISPLAY SETTINGS
1Select “Display Phone Status” or “Dis-
play Portable Player Status” .
2Select “On”.
3Select “Save” .
1Select “Default” .
2Select “Yes”.
zIf the state of “Bluetooth* Power” is
changed from “Off ” into “On” , Bluetooth®
connection will begin.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
When “Bluetooth* Power” is “On” and
the “START STOP ENGINE”
<“POWER”> switch is in ACCESSORY
or IGNITION ON <ON> mode, the
Bluetooth
® phone and portable player’s
connection status can be displayed.
(See “CHANGING “Bluetooth*
Power”” on page 202.)
INITIALIZING THE Bluetooth®
SETTINGS
The settings can be initialized.

210
1. AUDIO/VIDEO SYSTEM OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
2. SOME BASICS
This section describes some of the basic
features of the audio/video system.
Some information may not pertain to
your system.
Your audio/video system works when
the “START STOP ENGINE” <“POW-
ER”> switch is turned to ACCESSORY
or IGNITION ON <ON> mode.
CAUTION
●For vehicles sold in U.S.A. and Canada:
Part 15 of the FCC Rules
FCC WARNING: Changes or
modifications not expressly approved by
the party responsi ble for compliance
could void the user’s authority to operate
the equipment.
●Laser products
• USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS
RADIATION EXPOSURE.
• THE USE OF OPTICAL INSTRUMENTS WITH THIS
PRODUCT WILL INCREASE EYE
HAZARD.
NOTICE
●To prevent the 12-volt battery from being
discharged, do not leave the audio/video
system on longer than necessary when
the engine is not running <the hybrid sys-
tem is not operating>.
VOICE COMMAND SYSTEM
Press this switch to operate the voice
command system.
z For the operation of the voice command
system and its list of commands, see
pages 308 and 317.
AUDIO SPLIT SCREEN
DISPLAY
The audio split screen can be displayed
while the map screen is displayed. For
details, see page 46.

233
1. AUDIO/VIDEO SYSTEM OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
5
AUDIO/VIDEO SYSTEM
7. DVD PLAYER OPERATION
1Insert a disc into the disc slot.
zAfter insertion, the disc is automatically
loaded.
1Press the “” button and remove the
disc.
1Press the “MEDIA” button if a disc has
already been loaded in the disc slot.
For safety reasons, the DVD video discs
can only be viewed when the following
conditions are met:
(a) The vehicle is completely stopped.
(b) The “START STOP ENGINE” <“POWER”> switch is in
ACCESSORY or IGNITION ON
<ON> mode.
(c) The parking brake is applied.
While driving in DVD video mode, only
the DVD’s audio can be heard.
INSERTING A DISC
EJECTING A DISC
INFORMATION
●
If a disc is inserted with the label facing
down, it cannot be played.
PLAYING A DISC