light Lexus ES330 2004 Destination Input and Route Guidance / LEXUS 2004 ES330 (OM33633U) Workshop Manual

Finish
INTERIOR EQUIPMENT
72
Sun visors
1To block out glare from the front, swing the sun visor
down.
2To block out glare from the side, remove the sun visor
from the hook and swing it to the side.
3To block out glare coming obliquely from behind you,
slide the visor backward.
At this position, the vanity light does not come on.
INTERIOR LIGHT
To turn on the interior light, slide the switch.
The interior light switch has the following positions:
ONº Ð Keeps the light on all the time.
OFFº Ð Turns the light off.
DOORº Ð Turns the light on when any door is opened. The
light goes off when all the doors are closed. For details, see
Illuminated entry systemº on page 70.

Finish
INTERIOR EQUIPMENT
73
PERSONAL LIGHTS
To turn on the personal light, push the switch. To turn it
off, push the switch again.
ILLUMINATED ENTRY SYSTEM
14E133
1Ignition switch light
2Interior light (with the DOORº position)
3Door courtesy lights
4Foot lights

Finish
INTERIOR EQUIPMENT
74All of the lights will come on when any of the doors are
opened.* After all the doors are closed, the lights remain
on for about 15 seconds before fading out.**
NOTE:
* The operating condition can be changed.
** The duration of lighting can be changed and only the foot
lights can be set not to come on.
Ask your Lexus dealer for details.
However, in the following cases, the lights go out immediately:
All the doors are closed and the ignition key is in the ACCº
or ONº position. (The foot lights come on when the ignition
switch is in the ONº position. See the following Foot
lightsº.)
All the doors are locked.
When any of the door is unlocked, all of the lights will come on
and remain on for about 15 seconds before fading out.
Foot lights
The foot lights also come on when the ignition switch is in the
ONº position with the selector lever in the Pº position. When
the selector lever is moved out of the Pº position, the foot lights
will be dimmed.*
NOTE:
* The foot lights can be set to turn off when the selector lever
is moved out of the Pº position.
Ask your Lexus dealer for details.
When the instrument panel light control dial is turned fully
down, the foot lights will turn off.
CLOCK
The digital clock indicates the time with the ignition key at
the ACCº or ONº position. To reset the hour, press the
Hº button. To reset the minutes, press the Mº button.
To adjust the time to the nearest hour, press the :00º
button.
For example, if the :00º button is pressed when the time is
between 9:30 Ð 9:59 or between 10:01 Ð 10:29, the time will
change to 10:00.
With the tail lights on, the brightness of the time indication will
be reduced.
If the electrical power source has been disconnected from the
clock, the time display will automatically be set to 1:00 (one
o'clock).

Finish
INTERIOR EQUIPMENT
75
CIGARETTE LIGHTER AND
ASHTRAY
Cigarette lighter and ashtray
To use the cigarette lighter and ashtray, first push against
the ashtray cover. Then when the ashtray opens out,
press in the cigarette lighter. After it finishes heating up,
it automatically pops out ready for use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in the
ACCº position to use the lighter.
When finished with your cigarette, thoroughly extinguish it in
the ashtray to prevent other cigarette butts from catching fire.
After using the ashtray, push it back in completely.
To remove the ashtray, just pull it up.Use a Lexus genuine cigarette lighter or equivalent for
replacement.
CAUTION
To reduce the chance of injury in case of an accident or
sudden stop while driving, always completely close the
ashtray after use.

Finish
INTERIOR EQUIPMENT
77
GLOVE BOX
1Unlock2Open3Lock
To open the glove box door, pull the lever. To lock the
glove box door, insert the master key and turn it
clockwise.
With the tail lights on, the glove box light will come on when the
glove box door is open.
The trunk lid opener main switch is installed inside the glove
box. See page 89 for further information.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the glove box door closed
while driving.
REAR CONSOLE BOX
Upper tray
Console box

Finish
INTERIOR EQUIPMENT
78To access the upper tray, push the lock release button and
raise the lid. To access the console box, pull up the lock
release lever and raise the lid.
The rear console box light comes on when the tail lights are
turned on.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, always keep the rear console box closed
while driving.
GARAGE DOOR OPENER
The garage door opener (
Universal
Transceiver) is manufactured under license from
HomeLink
 and can be programmed to operate garage
doors, gates, entry doors, door locks, home lighting
systems, and security systems, etc.
(a) Programming the HomeLink
1Indicator light2Buttons
The HomeLink in your vehicle has 3 buttons and you can
store one program for each button.
To ensure correct programming into the HomeLink
, install a
new battery in the hand-held transmitter prior to programming.

Finish
INTERIOR EQUIPMENT
79 The battery side of the hand-held transmitter must be pointed
away from the HomeLink
 during the programming process.
For Canadian users, follow the procedure in Programming an
entrance gate/Programming all devices in the Canadian
marketº.
1. Decide which of 3 HomeLink
 buttons you want to program.
2. Place your hand-held garage transmitter 25 to 75 mm (1 to
3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Simultaneously press and hold the hand-held garage
transmitter button along with the selected HomeLink
 button.
4. When the indicator light on the HomeLink
 changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
5. Test the operation of the HomeLink
 by pressing the newly
programmed button. If programming a garage door opener,
check to see if the garage door opens and closes.If the garage door does not operate, identify if your garage
transmitter is of the Rolling Codeº type. Press and hold the
programmed HomeLink
 button. The garage door has the
rolling code feature if the indicator light (on the HomeLink)
flashes rapidly and then remains lit after 2 seconds. If your
garage transmitter is the Rolling Codeº type, proceed to the
heading Programming a rolling code systemº.
6. Repeat steps 2 through 5 for each remaining HomeLink

button to program another device.
Programming a rolling code system
If your device is Rolling Codeº equipped, it is necessary
to follow steps 1 through 4 under the heading
Programming the HomeLink
º before proceeding with
the steps listed below.
1. Locate the trainingº button on the ceiling mounted garage
door opener motor. The exact location and color of the button
may vary by brand of garage door opener. Refer to the owner's
guide supplied by the garage door opener manufacturer for the
location of this trainingº button.
2. Press the trainingº button on the ceiling mounted garage
door opener motor.
Following this step, you have 30 seconds in which to initiate
step 3 below.

Finish
INTERIOR EQUIPMENT
803. Press and release the vehicle's programmed HomeLink

button twice. The garage door may open. If the door does
open, the programming process is complete. If the door does
not open, press and release the button a third time. This third
press and release will complete the programming process by
opening the garage door.
The ceiling mounted garage door opener motor should now
recognize the HomeLink
 unit and be able activate the garage
door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLink

button to program another rolling code system.
Programming an entrance gate /
programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink buttons you want to
program.
2. Place your hand-held gate/device transmitter 25 to 75 mm
(1 to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Press and hold the selected HomeLink
 button.
4. Continuously press and release (cycle) the hand-held
gate/device transmitter button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
 changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.6. Test the operation of the HomeLink
 by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink

button to program another device.
Programming other devices
To program other devices such as home security systems,
home door locks or lighting, contact your authorized Lexus
dealer for assistance.
Reprogramming a button
Individual HomeLink
buttons cannot be erased, however, to
reprogram a single button, follow the procedure Programming
the HomeLink
º.
(b) Operating the HomeLink
To operate the HomeLink, press the appropriate HomeLink
button to activate the programmed device. The HomeLink
indicator light should come on. The HomeLink continues to
send the signal for up to 20 seconds as long as the button is
pressed.

Finish
INTERIOR EQUIPMENT
81
(c) Erasing the entire HomeLink memory (all
three programs)
To erase all previously programmed codes at one time, press
and hold down the 2 outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored
in the HomeLink

memory.
CAUTION
When programming the HomeLink Universal
Transceiver, you may be operating a garage door or
other device. Make sure people and objects are out
of the way of the garage door or other device to
prevent potential harm or damage.
Do not use this HomeLink
 Universal Transceiver
with any garage door opener that lacks the safety
stop and reverse feature as required by federal safety
standards. (This includes any garage door opener
model manufactured before April 1, 1982.) A garage
door opener which cannot detect an object (signaling
the door to stop and reverse), does not meet current
federal safety standards. Using a garage door
opener without these features increases risk of
serious injury or death.
This device complies with FCC Rules Part 15.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference that may
be received, including interference that may cause
undesired operation. WARNING: This transmitter
has been tested and complies with FCC and
DOC/MDC rules. Changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate the device.

Finish
INTERIOR EQUIPMENT
84
NOTICE
During hot weather, the interior of the vehicle becomes
very hot. Do not leave anything flammable or
deformable such as a lighter, glasses, etc. inside.