sensor LEXUS GS400 2000 Service Repair Manual

SS0CN±02
SS±60
± SERVICE SPECIFICATIONSBODY ELECTRICAL
216 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY ELECTRICAL
SERVICE DATA
DAYTIME RUNNING LIGHT RELAY (MAIN) (Wire Harness Side)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON or START)Battery positive voltage
5 ± Ground (Engine Stop)No voltage
5 ± Ground (Engine Running)Battery positive voltage
7 ± Ground (Constant)Battery positive voltage
9 ± Ground (Constant)Battery positive voltage
AUTOMATIC LIGHT CONTROL SENSOR
(Connector disconnected)
4 ± Ground (Ignition switch position LOCK or ACC)No voltage
4 ± Ground (Ignition switch position ON)5.2 ± 9.0 V
(Connector connected)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)9.5 V or more
HEADLIGHT BEAM LEVEL CONTROL ECU
(Connector disconnected)
A1 ± A5 (Ignition switch position OFF)26 ± 30 W
A1 ± A6 (Ignition switch position OFF)26 ± 30 W
A1 ± A7 (Ignition switch position OFF)26 ± 30 W
A1 ± A8 (Ignition switch position OFF)26 ± 30 W
A4 ± B4 (Ignition switch position ON and light control switch HEAD)Below 1.5 V
B1 ± B3 (Ignition switch position OFF)3.5 k ± 6.5 kW
B5 ± B7 (Ignition switch position OFF)3.5 k ± 6.5 kW
(Connector disconnected)
B2 ± B3 (Ignition switch position ON)Approx. 2.5 V
B6 ± B7 (Ignition switch position ON)Approx. 2.5 V
B1 ± B3 (Ignition switch position ON)5V
B5 ± B7 (Ignition switch position ON)5V
TURN SIGNAL FLASHER
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)Battery positive voltage
4 ± Ground (Constant)Battery positive voltage
LIGHT FAILURE RELAY (Wire Harness Side)
5 ± Ground (Light control switch position OFF)No voltage
5 ± Ground (Light control switch position TAIL or HEAD)Battery positive voltage
8 ± Ground (Ignition switch position LOCK or ACC)No voltage
8 ± Ground (Ignition switch position ON)Battery positive voltage
9 ± Ground (Stop light switch position OFF)No voltage
9 ± Ground (Stop light switch position ON)Battery positive voltage
10 ± Ground (Stop light switch position OFF)No voltage
10 ± Ground (Stop light switch position ON)Battery positive voltage
SPEEDOMETER (ON±VEHICLE)
USA:

SS0FI±01
SS±8
± SERVICE SPECIFICATIONSENGINE MECHANICAL (2JZ±GE)
164 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
No.3 timing belt cover x Cylinder head8.08071 in.´lbf
Intake air connector x Air intake chamber2828021
Throttle body bracket x Cylinder head2121015
Timing belt plate x Oil pump8.08071 in.´lbf
Idler pulley x Oil pump3535026
No.1 timing belt cover x Oil pump8.08071 in.´lbf
Camshaft timing pulley x Camshaft8181060
Straight screw plug x Camshaft timing pulley1515011
No.1 oil pipe x No.3 camshaft bearing cap5555041
Cylinder head cover x Cylinder head8.58575 in.´lbf
High±tension cord x Cylinder head cover8.08071 in.´lbf
Timing belt tensioner x Oil pump2727020
Crankshaft pulley x Crankshaft3303,300243
Drive belt tensioner x Cylinder head2121015
No.2 timing belt cover x Cylinder head8.08071 in.´lbf
PS pump front bracket x PS vane pump5859043
PS pump front bracket x Cylinder block5253038
Camshaft bearing cap x Cylinder head2020014
ECT sensor x Cylinder head19.620014
Engine hanger x Cylinder head4040030
Water outlet x Cylinder head2828021
Cylinder head x Cylinder head 1st
2nd
3rd35
Turn 90°
Turn 90°350
Turn 90°
Turn 90°26
Turn 90°
Turn 90°
No.3 camshaft bearing cap x Cylinder head Hexagon bolt5.05044 in.´lbf
No.4 timing belt cover x Cylinder head8.08071 in.´lbf
Cylinder head cover x Cylinder head8.58575 in.´lbf
Intake manifold x Cylinder head2828021
Manifold stay x Intake manifold4040030
Manifold stay x Cylinder block4040030
Vacuum control valve set x Intake manifold2121015
Exhaust manifold x Cylinder head4040830
Front exhaust pipe x Exhaust manifold4444032
Pipe support bracket x Transmission4444032
PS vane pump x Cylinder block57.959043
PS vane pump x A/C compressor57.959043
PS pump rear stay x PS pump bracket39.240029
PS pump rear stay x Manifold stay39.240030
Engine hanger x Cylinder head4040030
Rear support member x Body25.526019
Drive plate x Crankshaft8385061
Transmission x Cylinder block7273053
Starter x Transmission3738027
No.1 oil pan x Transmission3738027

± SERVICE SPECIFICATIONSENGINE MECHANICAL (2JZ±GE)
SS±9
165 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)Part tightened
N´mkgf´cmft´lbf
Drive plate x Torque converter clutch4849035
Rear support member x Engine rear mounting insulator13.513510
Front suspension crossmember x Engine mounting insulator7071452
PS gear housing x Front suspension member6566048
Sliding yoke x Steering intermediate shaft3536026
Transmission control rod x Shift lever131309
Transmission control rod x Transmission131309
A/C compressor x Cylinder block Stud bolt
Bolt and nut26
52265
53019
38
Fuel inlet hose x Fuel pipe support2930022
Front suspension member brace x Front suspension member5859043
Front suspension member brace x Strut bar bracket plate5859043
Connecting rod cap x Connecting rod 1st
2nd30
Turn 90°300
Turn 90°22
Turn 90°
Main bearing cap x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Rear oil seal retainer x Cylinder block6.06053
Engine mounting bracket x Cylinder block5959044
Fuel inlet pipe x Cylinder block2929021
No.1 oil pipe x Cylinder block5555041
Oil filter bracket x Cylinder block9090066
No.2 water bypass pipe x Water pump2121015
No.2 water bypass pipe x Cylinder block2121015
Generator x Water pump4040030
Generator x Cylinder block4040030
Front exhaust pipe x Center exhaust pipe4444032
Center exhaust pipe x Tailpipe4444032
Heated oxygen sensor x Front exhaust pipe4545033

SF0N1±03
± SFI (2JZ±GE)SFI SYSTEM
SF±1
1467 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SFI SYSTEM
PRECAUTION
1. BEFORE WORKING ON FUEL SYSTEM, DISCON-
NECT NEGATIVE (±) TERMINAL CABLE FROM BAT-
TERY
HINT:
Any diagnostic trouble code retained by the ECM will be erased
when the battery negative (±) terminal cable is removed from
the battery.
Therefore, if necessary, read the diagnostic trouble code(s) be-
fore removing the negative (±) terminal cable from the battery.
2. DO NOT SMOKE OR WORK NEAR AN OPEN FLAME
WHEN WORKING ON FUEL SYSTEM
3. KEEP GASOLINE AWAY FROM RUBBER OR LEATH-
ER PARTS
4. MAINTENANCE PRECAUTIONS
(a) Precaution when the connecting gauge.
Use battery as the power source for the timing light, etc.
(b) In the event of engine misfire, these precautions should
be taken.
(1) Check proper connection of battery terminals, etc.
(2) Handle high±tension cords carefully.
(3) After repair work, check that the ignition coil termi-
nals and all other ignition system lines are recon-
nected securely.
(4) When cleaning the engine compartment, be espe-
cially careful to protect the electrical system from
water.
(c) Precautions when the handling heated oxygen sensors.
(1) Do not allow oxygen sensor to drop or hit against an
object.
(2) Do not allow the sensor to come into contact with
water.
5. IF VEHICLE IS EQUIPPED WITH MOBILE RADIO SYS-
TEM (HAM, CB, ETC.)
If the vehicle is equipped with a mobile communication system,
refer to the precaution in the IN section.
6. AIR INDUCTION SYSTEM
(a) Separation of the engine oil dipstick, oil filler cap, PCV
hose, etc. may cause the engine to run out of tune.
(b) Disconnection, looseness or cracks in the parts of the air
induction system between the throttle body and cylinder
head will cause air suction and cause the engine to run
out of tune.

SF151±01
B08999
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
21 (210, 15)
21 (210, 15)
VSV Connector for EVAP
Camshaft Position Sensor Connector
No.2 Vacuum Pipe
Accelerator Cable
EVAP Hose
Noise Filter
Connector
Vacuum
Hose
Throttle Position
Sensor Connector

Gasket
PS Air Hose
Engine Wire Clamp

Gasket
Oil Dipstick and
Guide for A/T
Engine Wire
Clamp
42 (420, 31)
Fuel Pressure Pulsation Damper

Gasket

O±Ring
Fuel Inlet Pipe Delivery Pipe
21 (210, 15)
Spacer
Injector Connector
O±Ring
O±Ring
Injector

Insulator

Grommet
28 (280, 21)
Engine Cover
SF±20
± SFI (2JZ±GE)INJECTOR
1486 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMPONENTS

SF0NB±04
B01579
± SFI (2JZ±GE)INJECTOR
SF±21
1487 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2. REMOVE AIR INTAKE CHAMBER (See page SF±46)
3. REMOVE FUEL PRESSURE PULSATION DAMPER
(See page SF±26)
4. REMOVE DELIVERY PIPE AND INJECTORS
NOTICE:

Be careful not to drop the injectors when removing
the delivery pipe.

Pay attention to put any hung load on the injector to
and from the side direction.
(a) Disconnect the 6 injector connectors.
(b) Disconnect the camshaft position sensor connector.
(c) Disconnect the throttle position sensor connector.
(d) Disconnect the VSV connector for EVAP.
(e) Remove the 3 bolts and delivery pipe together with the 6
injectors.
(f) Pull out the 6 injectors from the delivery pipe.
(g) Remove the O±rings, grommet and insulator from each
injector.
(h) Remove the 3 spacers from the intake manifold.

SF0ND±04
B01220
New Insulator
New O±Ring
New Grommet New O±Ring
B01571
Turn
Outward
Connector
B01580
RotateUpward SF±24
± SFI (2JZ±GE)INJECTOR
1490 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL INJECTORS AND DELIVERY PIPE
(a) Install new insulator and grommet to each injector.
(b) Apply a light coat of spindle oil or gasoline to 2 new O±
rings and install them to each injector.
(c) Apply a light coat of spindle oil or gasoline on the place
where a delivery pipe touches an O±ring of the injector.
(d) While turning the injector clockwise and counterclock-
wise, push it to the delivery pipe. Install the 6 injectors.
(e) Position the injector connector outward.
(f) Place the 3 spacers in position on the intake manifold.
(g) Apply a light coat of spindle oil or gasoline on the place
where a intake manifold touches an O±ring of the injector.
(h) Place the 6 injectors together with the delivery pipe and
3 bolts in position on the intake manifold.
(i) Temporarily install the 3 bolts holding the delivery pipe to
the intake manifold.
(j) Check that the injectors rotate smoothly.
HINT:
If injectors do not rotate smoothly, the probable cause is incor-
rect installation of O±rings. Replace the O±rings.
(k) Position the injector connector upward.
(l) Connect the 6 injector connectors.
HINT:
The Nos.1, 3, 5 injector connectors and dark gray, and the
Nos.2, 4, 6 injector connectors are brown.
(m) Tighten the 3 bolts holding the delivery pipe to the intake
manifold.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(n) Connect the camshaft position sensor connector.
(o) Connect the throttle position sensor connector.
(p) Connect the VSV connector for EVAP.
2. INSTALL FUEL PRESSURE PULSATION DAMPER
(See page SF±27)
3. INSTALL AIR INTAKE CHAMBER
(See page SF±49)
4. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.

SF0NL±05
B09506
B01608
B01982
LEXUS
Hand±Held
Tester SF±32
± SFI (2JZ±GE)THROTTLE BODY
1498 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
THROTTLE BODY
ON±VEHICLE INSPECTION
1. REMOVE ENGINE COVER
Remove the 4 nuts and engine cover.
2. INSPECT SYSTEM OPERATION
(a) Check that the throttle linkage moves smoothly.
(b) Inspect the throttle control motor for operating sound.
(1) Turn the ignition switch ON.
(2) When turning the accelerator pedal position sensor
lever, check the running sound of the motor. Also,
check that there is no friction sound.
If operation is not as specified, check the throttle control motor,
wiring and ECM.
(c) Inspect the throttle position sensor and accelerator pedal
position sensor function.
(1) Connect the LEXUS hand±held tester to the DLC3.
(2) When turning the accelerator pedal position sensor
lever to the full±open position, check that the
throttle valve opening percentage (THROTTLE
POS) of the CURRENT DATA showns the standard
value.
Throttle valve opening percentage: 60 % or more
If operation is not as specified, check that the throttle position
sensor, accelerator pedal position sensor, wiring and ECM.
(d) Start the engine, and check that the Malfunction Indicator
Lamp (MIL) does not light up.
(e) Inspect the air assist system.
(1) Allow the engine to warm up to normal operating
temperature.

B09507
B01620
Ohmmeter3 (CL±)
4 (CL+)
1 (M+)
2 (M±)
B01942VCOhmmeter
E2
B01943
VC Ohmmeter
E2
± SFI (2JZ±GE)THROTTLE BODY
SF±33
1499 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(2) Turn the A/C switch ON and OFF, and check the idle
speed.
Idle speed (Transmission in neutral):
700 ± 50 rpm (A/C OFF)
750 ± 50 rpm (A/C ON)
NOTICE:
Perform inspection under condition without electrical load.
(3) With engine idling, pinch the air assist hose and
check that engine speed drops, and then returns
back up to idle speed.
If operation is not as specified, check the throttle body, wiring
and ECM.
(f) After checking the above (b) to (e), perform the diving test
and check that there is no sense of incongruity.
3. INSPECT THROTTLE CONTROL MOTOR
(a) Disconnect the throttle control motor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minal 3 (CL±) and 4 (CL+).
Resistance: 4.2 ± 5.2 W at 20°C (68°F)
(c) Using an ohmmeter, measure the resistance between ter-
minal 1 (M+) and 2 (M±).
Resistance: 0.3 ± 100 W at 20°C (68°F)
If the resistance is not as specified, replace the throttle control
motor. (See page SF±37)
(d) Reconnect the throttle control motor connector.
4. INSPECT THROTTLE POSITION SENSOR
(a) Disconnect the throttle position sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals VC and E2.
Resistance: 1.2 ± 3.2 kW at 20°C (68°F)
If the resistance is not as specified, replace the throttle position
sensor. (See page SF±37)
(c) Reconnect the throttle position sensor connector.
5. INSPECT ACCELERATOR PEDAL POSITION SEN-
SOR
(a) Disconnect the accelerator pedal position sensor con-
nector.
(b) Using an ohmmeter, measure the resistance between ter-
minals VC and E2.
Resistance: 1.2 ± 3.2 kW at 20°C (68°F)
If the resistance is not as specified, replace the accelerator ped-
al position sensor. (See page SF±37)

SF±34
± SFI (2JZ±GE)THROTTLE BODY
1500 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Reconnect the accelerator pedal position sensor connec-
tor.
6. REINSTALL ENGINE COVER
Reinstall the engine cover with the 4 nuts.