bulb LEXUS GS400 2000 Service Repair Manual

D01090
Shift Lever Knob
Shift Lever Knob
Cover
Shift Lever
Sub±AssemblyShift Lever Detent Pin
Shift Lever Spring Damper
Compression Spring
Shift Lock Release Link
Indicator Lamp Wire Position Indicator Housing
Position Indicator
Lens
Slide Cover
Shift Lever Guide
Housing
Shift Lever
Anti±Rattle Cushion
Shift Lock
Plate Stopper
Shift Lever
Torsion Spring
Spring Holder
Lower Control Shaft Bushing
Lower Control Shaft Piece
Plate Washer
Shift Lever Boot Connecting Rod Swivel
Shift Lock Solenoid Link
Control ShaftPin
BulbConnector
Compression Spring
Plate WasherRoller
Spacer
Clip Control Lever
2.0 (20, 17 in.´lbf)
3.9 (40, 35 in.´lbf)
2.0 (20, 17 in.´lbf)
13 (128, 9)
Shift Lock
Control Unit
AssemblyShift Lock Release
Spring
No.1 Shift Lock
Switch PlateShift Lever Plate
Spacer
N´m (kgf´cm, ft´lbf)
: MP grease: Specified torqueShift Lever Cap
Wire Protector

Shift Lever Nut
Shift Lock
Plate Stopper
Cap

Slotted
Spring Pin

Non±reusable part
± AUTOMATIC TRANSMISSIONFLOOR SHIFT ASSEMBLY
AT±15
1963 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

D01066
D01067
D0190412
3
D01069
D01070
Tip of Screwdriver
AT±18
± AUTOMATIC TRANSMISSIONFLOOR SHIFT ASSEMBLY
1966 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. REMOVE SHIFT LEVER GUIDE HOUSING AND INDI-
CATOR LAMP SUB±ASSEMBLY
(a) Disconnect the indicator lamp wire and connector from
the shift lever plate.
(b) Remove the shift lever guide housing with the indicator
lamp sub±assembly from the shift lever plate.
(c) Remove the indicator lamp sub±assembly from the shift
lever guide housing.
8. DISASSEMBLE INDICATOR LAMP SUB±ASSEMBLY
(a) Remove the bulb from the indicator lamp wire sub±as-
sembly.
(b) Using a small screwdriver, remove the terminals of the in-
dicator lamp wire sub±assembly from the connector, as
shown in the illustration.
9. REMOVE SHIFT LEVER DETENT PIN, SHIFT LEVER
SPRING DAMPER AND COMPRESSION SPRING
FROM SHIFT LEVER SUB±ASSEMBLY
10. REMOVE SPRING HOLDER AND SHIFT LEVER TOR-
SION SPRING
(a) Using a screwdriver, remove the spring holder.

D01073
D01072
D01071
D01069
D01068
AT±24
± AUTOMATIC TRANSMISSIONFLOOR SHIFT ASSEMBLY
1972 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. INSTALL AND TORQUE 2 SHIFT LOCK CONTROL
UNIT ASSEMBLY SET SCREWS
Torque: 2.0 N´m (20 kgf´cm, 17 in.´lbf)
8. INSTALL SPRING HOLDER AND SHIFT LEVER TOR-
SION SPRING
(a) Install the shift lever torsion spring.
(b) Install the spring holder.
9. INSTALL SHIFT LEVER DETENT PIN, SHIFT LEVER
SPRING DAMPER AND COMPRESSION SPRING TO
SHIFT LEVER SUB±ASSEMBLY
10. ASSEMBLE INDICATOR LAMP SUB±ASSEMBLY
(a) Install the terminals of the indicator lamp wire sub±as-
sembly to the connector.
(b) Install the bulb to the indicator lamp wire sub±assembly.
11. INSTALL SHIFT LEVER GUIDE HOUSING AND INDI-
CATOR LAMP SUB±ASSEMBLY
(a) Install the indicator lamp sub±assembly to the shift lever
guide housing.
(b) Install the shift lever housing with the indicator lamp sub±
assembly to the shift lever plate.

BE01I±09
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±1
2302 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY ELECTRICAL SYSTEM
PRECAUTION
HINT:
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM

Halogen bulbs have pressurized gas inside and require special handling. They can burst if scratched
or dropped. Hold a bulb only by its plastic or metal case. Don't touch the glass part of a bulb with bare
hands.

When high voltage socket of discharge headlight is touched with the light control switch HEAD, high
voltage of 20,000 V is momentarily generated. This might lead to a serious accident.

Never connect the tester to the high voltage socket of discharge headlight for measurement, as this
leads to a serious accident because of high voltage.

When performing operation related to the discharge headlight, make sure to do it in the place with no
water of rain to prevent electric shock, with light control switch OFF, battery terminal removed, connec-
tor of light control ECU disconnected.

When performing operation related to the discharge headlight, make sure to do it after assembling has
been completely over and never light up without a bulb installed.

Do not light up the discharge headlight using another power source except vehicle's.

When there is a defect on the discharge headlight or any shock has been applied to it, replace the light
with a new one.
Even if the light operates normally, there is a possibility that the fail±safe function works.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The LEXUS GS300/ 400 is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in the correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in-
cluding removal or installation of parts, inspection or replacement), be sure to read the precautionary notices
in the RS section.
3. COMBINATION METER SYSTEM
The cold cathode tube connectors (Connector ºKºand ºLº) in the combination meter are charged with high
voltage AC current when power is supplied, so do not touch them when they are charged.

BE19B±01
± BODY ELECTRICALTROUBLESHOOTING
BE±3
2304 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
Ignition Switch:
SymptomSuspect AreaSee page
Ignition switch is not set to each position.4. Ignition switch
5. Power source circuitBE±31
±
Key Unlock Warning Switch:
SymptomSuspect AreaSee page
Key unlock warning system does not operate.
(The buzzer does not sound when the driver's door is opened with
the ignition OFF and key inserted)1. Key Unlock Warning Switch
2. Door Courtesy Switch
3. Wire HarnessBE±31
BE±60
±
Key unlock warning system does not operate.
(The buzzer sounds when the ignition key is ACC or ON)1. Ignition Switch
2. Wire HarnessBE±31
±
HEADLIGHT AND TAILLIGHT SYSTEM:
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
HINT:
To inspect the bulb and light control ECU, replace them with the ones working normally and judge whether
they work normally or not.
SymptomSuspect AreaSee page
ºAutomatic light control systemº does not operate.
1. Automatic Light Control Sensor
2. Light Control Switch
3. Door Courtesy Switch
4. Wire Harness
5. Body No.2 ECUBE±37
BE±37
BE±60
±
DI±820
Auto turn±off system does not operate when the driver's door is
opened.1. Drivers Door Courtesy SwitchBE±60
Auto turn±off system:
Headlight and taillight do not come on.1. Body ECU No.2
2. Wire HarnessDI±820
±
Auto turn±off system:
Headlight and taillight stay on.1. Body ECU No.2
2. Wire HarnessDI±820
±
USA:
SymptomSuspect AreaSee page
Only one headlight comes on.
1. Bulb
2. *Light Control ECU
3. Wire Harness±
±
±
ºLO±Beamº does not light (All).
1. Headlight Control Relay
2. *Light Control ECU
3. Wire HarnessBE±37
±
±
ºLO±Beamº does not light (One side).
1. Bulb
2. H±LP L±LWR Fuse
3. H±LP R±LWR Fuse
4. *Light Control ECU
5. Wire Harness±
BE±21
BE±21
±
±
ºHI±Beamº does not light (All).1. Headlight Dimmer Switch
2. Wire HarnessBE±37
±

BE±4
± BODY ELECTRICALTROUBLESHOOTING
2305 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) ºHI±Beamº does not light (One side).
1. Bulb
2. H±LP L±UPR Fuse
3. H±LP R±UPR Fuse
4. Wire Harness±
BE±21
BE±21
±
ºFlashº does not light.
1. H±LP L±UPR Fuse
2. H±LP R±UPR Fuse
3. Headlight Dimmer Switch
4. *Light Control ECU
5. Wire HarnessBE±21
BE±21
BE±37
±
±
ºFlashº does not light.
1. Bulb
2. *Light Control ECU
3. Wire Harness±
±
±
Headlight does not come on.
1. Headlight Control Relay
2. Light Control Switch
3. *Light Control ECU
4. Wire HarnessBE±37
BE±37
±
±
Headlight does not come on.
1. Bulb
2. *Light Control ECU
3. Wire Harness±
±
±
Headlight flickers.
1. Bulb
2. *Light Control ECU
3. Wire Harness±
±
±
Headlight is dark.
1. Bulb
2. *Light control ECU
3. Wire Harness±
±
±
Only one taillight comes on.1. Bulb
2. Wire Harness±
±
Taillight does not come on.
(Headlight is normal)
1. TAIL Fuse
2. GAUGE Fuse
3. Taillight Control Relay
4. Light Failure Relay
5. Light Control Switch
6. Wire HarnessBE±21
BE±21
BE±37
BE±92
BE±37
±
Taillight does not come on.
(Headlight does not light)1. Light Control Switch
2. Wire HarnessBE±37
±
Rear combination light does not come on.
1. Light Failure Relay
2. Wire Harness
3. BulbBE±92
±
±
*: HID Type
CANADA:
SymptomSuspect AreaSee page
Only one headlight comes on.
1. Daytime Running Light No.2, 3, 4 Relay
2. Daytime Running Light Main Relay
3. Bulb
4. *Light Control ECU
5. Wire HarnessBE±37
BE±37
±
±
±
ºLO±Beamº does not light (All).
1. Headlight Control Relay
2. *Light Control ECU
3. Wire HarnessBE±37
±
±
ºLO±Beamº does not light (One side).
1. Bulb
2. H±LP L±LWR Fuse
3. H±LP R±LWR Fuse
4. *Light Control ECU
5. Wire Harness±
BE±21
BE±21
±
±

± BODY ELECTRICALTROUBLESHOOTING
BE±5
2306 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) ºHI±Beamº does not light (All).
1. Headlight Dimmer Switch
2. Daytime Running Light Main Relay
3. Wire HarnessBE±37
BE±37
±
ºHI±Beamº does not light (One side).
1. Bulb
2. H±LP L±UPR Fuse
3. H±LP R±UPR Fuse
4. Daytime Running Light No.3 Relay
5. Wire Harness±
BE±21
BE±21
BE±37
±
ºFlashº does not light.
1. Headlight Dimmer Switch
2. Daytime Running Light Main Relay
3. Wire HarnessBE±37
BE±37
±
Headlight does not come on.
1. Headlight Control Relay
2. Daytime Running Light Main Relay
3. Daytime Running Light No.2, 3, 4 Relay
4. Headlight Dimmer Switch
5. Light Control Switch
6. Wire Harness
7. *Light Control ECU
8. BulbBE±37
BE±37
BE±37
BE±37
BE±37
±
±
±
Headlight does not come on with light control switch in HEAD.
1. Light Control Switch
2. *Light Control ECU
3. Wire HarnessBE±37
±
±
Headlight does not go out with light control switch in OFF.
1. Headlight Control Relay
2. *Light Control ECU
3. Wire HarnessBE±37
±
±
Headlight flickers.
1. Bulb
2. *Light Control ECU
3. Wire Harness±
BE±37
±
Headlight is dark.
1. Bulb
2. *Light control ECU
3. Wire Harness±
±
±
Taillight does not come on with light control switch in TAIL.
1. Taillight Control Relay (Instrument Panel J/B)
2. Light Control Switch
3. Wire HarnessBE±37
±
±
Taillight does not go out with light control switch in OFF.
1. Taillight Control Relay
2. Light Control Switch
3. Wire HarnessBE±37
BE±37
±
Headlight does not come on with engine running and light control
switch in OFF.
1. ECU±B Fuse
2. GAUGE Fuse
3. Daytime Running Light Main Relay
4. Daytime Running Light No.2, 3, 4 Relay
5. Generator L Terminal
6. Parking Brake Switch
7. Wire HarnessBE±21
BE±21
BE±37
BE±37
DI±853
BE±92
±
*: HID Type

BE±6
± BODY ELECTRICALTROUBLESHOOTING
2307 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HEADLIGHT BEAM LEVEL CONTROL SYSTEM
SymptomSuspect AreaSee page
Beam axis is not controlled. (It is not initialized.)
Headlight Beam Level Control System does not operate.
1. ECU±IG Fuse
2. Headight Beam Level Control Actuator
3. Headlight Beam Level Control ECU
4. Wire Harness SideBE±21
BE±50
BE±50
±
Beam axis is not controlled. (It is initialized.)
Headlight Beam Level Control System does not operate.1. Height Control Sensor
2. Headlight Beam Level Control ECU
3. Wire Harness SideBE±50
BE±50
±
Controlled angle of head light is unusual.
(The angle is controlled.)
1. Height Control Sensor
2. Headlight Beam Level Control ECU
3. Headlights
4. Wire Harness Side±
BE±50
BE±3
±
Beam axis position is not stable during driving.
1. ABS System
2. Headlights
3. Wire HarnessDI±387
BE±3
±
FOG LIGHT SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Fog light does not light up with light control SW HEAD
(Headlight is normal.)
1. FOG Fuse
2. Fog Light Relay
3. Fog Light Switch
4. Wire Harness
5. Body No.2 ECUBE±21
BE±53
BE±53
±
±
Fog light does not light up with light control SW HEAD
(Headlight does not light).1.*1 Other Parts
2. Wire Harness±
±
Only one light does not light up.1. Bulb
2. Wire Harness±
±
*1: Inspect Headlight System
TURN SIGNAL AND HAZARD WARNING SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. GAUGE Fuse
2. TURN HAZ Fuse
3. Ignitioin Switch
4. Turn Signal Flasher Relay
5. Wire HarnessBE±21
BE±21
BE±31
BE±56
±
Hazard warning light does not light up.
(Turn is normal)1. Hazard Warning Switch
2. Wire HarnessBE±56
±
Turn signal does not light up.
(Hazard is normal)1. Turn Signal Switch
2. Wire HarnessBE±56
±
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE±56
±
Only one bulb does not light up.1. Bulb
2. Wire Harness±
±

± BODY ELECTRICALTROUBLESHOOTING
BE±7
2308 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INTERIOR LIGHT SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
All the lights do not come ON.1. DOME Fuse
2. Body ECU NO.2BE±21
±
The light does not come ON when the driver's door is opened.1. Driver's Door Courtesy Switch
2. Wire HarnessBE±60
±
The light does not come ON when the passenger's door is
opened.1. Passenger's Door Courtesy Switch
2. Wire HarnessBE±60
±
The light does not come on when the rear±right door is opened.1. Rear±Right Door Courtesy Switch
2. Wire HarnessBE±60
±
The light does not come on when the rear±left door is opened.1. Rear±Left Door Courtesy Switch
2. Wire HarnessBE±60
±
Only one of the bulbs comes ON.Bulb±
The illumination does not fade out when all the doors are closed.1. Courtesy Switch
2. Wire HarnessBE±60
±
The illumination does not fade out immediately when the ignition
switch is turned to ACC or ON within 15 seconds after all the
doors are closed.1. Ignition Switch
2. RADIO NO.2 Fuse
3. GAUGE Fuse
4. Wire HarnessBE±31
BE±21
BE±21
±
The illumination does not fade out immediately when all the doors
are locked within 15 seconds after they are closed.1. Door Unlock Detection Switch
2. Wire HarnessBE±131
±
Interior light does not light up.
(in front personal light)1. Bulb
2. Front Personal Light
3. Wire Harness±
BE±60
±
Front personal light does not light up.
1. Bulb
2. Front Personal Light
3. Wire Harness±
BE±60
±
Rear personal light does not light up.
1. Bulb
2. Rear Personal Light
3. Wire Harness±
BE±60
±
Vanity light does not light up.
1. Bulb
2. Vanity Light
3. Wire Harness±
BE±60
±
Luggage compartment light does not light up.
1. Bulb
2. Luggage Compartment Door Courtesy Switch
3. Wire Harness±
BE±60
±
Courtesy light does not light up.
1. Bulb
2. Door Courtesy Switch
3. Wire Harness±
BE±60
±

BE±8
± BODY ELECTRICALTROUBLESHOOTING
2309 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BACK±UP LIGHT SYSTEM
SymptomSuspect AreaSee page
Back±Up Light does not light up.
1. GAUGE Fuse
2. Ignition Switch
3. Wire Harness
4. BulbBE±21
BE±31
±
±
Back±Up Light remains always on.1. Park/ Neutral Position Switch
2. Wire HarnessDI±372
±
Only one light does not light up.1. Bulb
2. Wire Harness±
±
STOP LIGHT SYSTEM
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse
2. Stop Light Switch
3. Light Failure Relay
4. Wire HarnessBE±21
BE±70
BE±92
±
Stop light always lights up.1. Stop Light Switc
2. Wire HarnessBE±70
±
Only one light always lights up.Wire Harness±
Only one light does not light up.1. Bulb
2. Wire Harness±
±
HEADLIGHT CLEANER SYSTEM
SymptomSuspect AreaSee page
ºHeadlight Cleaner Systemº does not operate
(All)
1. H±LP CLN Fuse
2. WASHER Fuse
3. Ignition Switch
4. Headlight Cleaner Switch
5. Headlight Cleaner Relay
6. Headlight Cleaner Motor
7. Headlight Cleaner Nozzle and Hose
8. Wire HarnessBE±21
BE±21
BE±31
BE±73
BE±73
±
±
±
Washer fluid does not spray.Headlight Cleaner Nozzle and Hose±
WIPER AND WASHER SYSTEM
SymptomSuspect AreaSee page
Wipers and washer do not operate.
1. WIP Fuse
2. Wiper Switch
3. Wiper Motor
4. Wire HarnessBE±21
BE±77
BE±77
±
Wipers do not operate in LO, HI or MIST.
1. Wiper Switch
2. Wiper Motor
3. Wire HarnessBE±77
BE±77
±
Wipers do not operate in INT.
1. Wiper Switch
2. Wiper Motor
3. Wire HarnessBE±77
BE±77
±
Washer motor does not operate.
1. WASHER Fuse
2. Washer Switch
3. Washer Motor
4. Wire HarnessBE±21
BE±77
BE±77
±
Wipers do not operate when washer switch ON.
1. WASHER Fuse
2. Washer Switch
3. Wiper Motor
4. Wire HarnessBE±21
BE±77
BE±77
±