check engine Lexus GS430 2006 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2005 PROD. OWNER'S MANUAL (OM30649U)

Page 5 of 622

IMPORTANT INFORMATION ABOUT YOUR LEXUS
v
Accessories, spare parts and modification of
your Lexus
A wide variety of non−genuine spare parts and accessories for
Lexus vehicles are currently available in the market. You
should know that Toyota does not warrant these products and
is not responsible for their performance, repair, or
replacement, or for any damage they may cause to, or adverse
effect they may have on, your Lexus vehicle.
This vehicle should not be modified with non −genuine Lexus
products. Modification with non −genuine Lexus products
could af fect its performance, safety or durability, and may even
violate governmental regulations. In addition, damage or
performance problems resulting from the modification may not
be covered under warranty.
Spark ignition system of your Lexus
The spark ignition system in your Lexus meets all
requirements of the Canadian Interference− Causing
Equipment Standard.
Installation of a mobile twoway radio system
As the installation of a mobile two −way radio system in your
vehicle could affect electronic systems such as the multiport
fuel injection system/sequential multiport fuel injection system,
cruise control system, dynamic radar cruise control system,
anti− lock brake system, SRS airbag system and seat belt
pretensioner system, be sure to check with your Lexus dealer
for precautionary measures or special instructions regarding
installation.
Tires and loading on your Lexus
Underinflated or overinflated tire pressure and the
excess load may result in the deterioration of steering
ability and braking ability, leading to an accident. Check
the tire inflation pressure periodically and be sure to
keep the load limits given in this Owner’s Manual. For
details about tire inflation pressure and load limits, see
page 539 and 456.
Scrapping of your Lexus
The SRS airbag and seat belt pretensioner devices in your
Lexus contain explosive c hemicals. If the vehicle is scrapped
with the airbags and seat belt pretensioners left as they are,
this may cause an accident such as fire. Be sure to have the
systems of the SRS airbag and seat belt pretensioner removed
and disposed of by a qualified service shop or by your Lexus
dealer before you scrap your vehicle.
Leak detection pump
This pump performs fuel evaporation leakage check. This
check is done several hours after the engine is turned off. So
you may hear sound coming from underneath the luggage
compartment for several minutes. It does not indicate a
malfunction.

Page 6 of 622

HOW TO USE THIS MANUAL
vi
HOW TO USE THIS MANUAL
The contents of this manual are explained briefly on this
page to help you make the best use of the manual. Please
read this page and the rest of the Owner’s Manual
carefully to make sure you fully understand the operation
of your vehicle.
This will help you enjoy safe and comfortable driving.
TABLE OF CONTENTS
The table of contents and the pictorial index provide easy
reference to the appropriate pages.
BASIC OPERATION QUICK REFERENCE
Operation of basic equipment is briefly explained in an easily
understandable way for quick reference.
SECTION 1 INSTRUMENTS AND CONTROLS
The vehicle’s equipment is divided into the 8 groups listed
below. Use of the equipment is explained, including any points
you should pay particular attention to.
1. Keys and doors
2. Switches
3. Gauges, meters and service reminder indicators
4. Interior equipment
5. Exterior equipment
6. Occupant restraint systems
7. Steering wheel and mirrors
8. Touch screen
SECTION 2 AIR CONDITIONING AND AUDIO
The features of the vehicle’s air conditioning and audio are
explained in detail. Be sure to read this section so that you can
make full use of them.
SECTION 3 STARTING AND DRIVING
Starting the engine, driving, stopping, operation of features
affecting vehicle handling, hints on vehicle safety and safe
driving techniques are all explained. Please read everything
in this section, and remember − drive safely!
SECTION 4 IN CASE OF AN EMERGENCY
This section explains what to do in the event of an urgent
situation such as the engine not starting or getting a flat tire,
etc. If such a problem occu rs, check the contents of this
Owner’s Manual and follow the instructions given.
SECTION 5 MAINTENANCE
This section explains the importance of regular maintenance.
Regular and periodic inspection and maintenance of your
Lexus will help to keep your vehicle in its best condition.
SECTION 6 SERVICE PROCEDURES AND
SPECIFICATIONS
Simple maintenance procedure and service data are provided
here for your reference should you wish to perform inspection
and maintenance yourself.

Page 32 of 622

KEYS AND DOORS
11
If the electronic key battery is discharged, the entry function
and wireless remote control cannot be used. Use the
mechanical key integrated into
the electronic key by inserting
it in the door keyhole to lock or unlock doors and into the trunk
lid keyhole to unlock the trunk lid. To start the engine, see
“Starting the engine when the electronic key battery is
discharged” on page 27. In order to activate the entry function
and wireless remote control, the battery should be replaced.
For details, see “Replacing the battery” on page 33.
(a) Engine immobilizer
G11009
The engine immobilizer is a theft prevention function.
When you enter the vehicle carrying an electronic key and
press the engine switch, the electronic code in the key is
automatically checked to determine whether it
corresponds to the registered ID code for the vehicle. If
the ID code is verified, you can start the engine.
The system is automatically set when the engine switch is off.
The indicator light will start flashing to show the system is set.

Page 36 of 622

KEYS AND DOORS
15
ALARMS AND WARNING MESSAGES
Your Lexus is equipped with alarms inside and outside, as
well as warning messages in the multiinformation
display,
that remind you if there is a problem involving the
entry function.
Cases which are expected to happen frequently are
shown in the illustrations and the other cases are
described in the table. If an alarm or warning message
comes on, check to see what the problem is referring to
the illustrations and table, and take the appropriate
measure.
If a warning message appears, the master warning light
will blink.
G11025
 When a door is opened and closed with the engine
switch in “ACC” or “IGON” mode and with the selector
lever in the “P” position, and then the electronic key is
carried outside of the vehicle.
Inside alarm: One chime
Outside alarm: 3 beeps
Multiinformation display: “KEY IS NOT DETECTED”
See page 91 for details.

Page 43 of 622

KEYS AND DOORS
22UNLOCKING THE DOOR(S) WITH ENTRY FUNCTION
G11032
When you take hold the back side of the outside door
handle on the driver’s door carrying an electronic key, the
driver’s door will be unlocked. When you take hold the
back
side of the outside door handle except on the driver’s
door, carrying an electronic key, all the doors will be
unlocked. At this time, two beeps will sound and turn
signal lights flash twice.
When you get close to your vehicle (about 1 m (3 ft.) from each
outside door handle), and are carrying the electronic key, the
electronic code emitted from the key is automatically checked
to determine if it corresponds to the registered ID code for the
vehicle. After this, the outer foot lights come on. (For outer foot
lights, see “Outer foot lights” on page 208.)
You can select the doors to be unlocked. For details, see
“Changing the doors to be unlocked” on page 23. When the door(s) is(are) unlock
ed, the interior lights come on
for 15 seconds if the interior light switch is in the “DOOR”
position. However, the interior lights go out when you push the
power door lock switch in the lock position or select the engine
switch in “ACC” or “IG− ON” mode. For further information, see
“Interior lights” on page 98.
You have 30 seconds to open a door after operating the
unlocking function. If a door is not opened by then, all the doors
will be automatically locked again.
INFORMATION
 When unlocking the door(s), be sure to take hold of
the back side of the outside door handle firmly as
shown in the illustration. Taking hold of the handle
with a gloved hand might cause a delay in unlocking
or may not unlock.
 When you take hold of the handle to unlock the
door(s), be sure to confirm that the door(s) has(have)
been unlocked. If the turn signal lights flash twice,
two beeps sound outside the vehicle, the doors are
unlocked. At this time, you can pull the outside door
handle to open the door. If you quickly move closer
to the vehicle or pull the outside door handle quickly,
the doors might not unlock. If you cannot open the
door by pulling the outside door handle at this time,
push it back to the original position and then pull it
out again.

Page 95 of 622

GAUGES, METERS AND SERVICE REMINDER INDICATORS
74IF THIS INDICATOR OR
BUZZER COMES ON ...
DO THIS.
(p)Key reminder
buzzerTurn off the engine
switch.
(a) Brake System Warning Light (red) and Buzzer
This light comes on in the following cases when the engine
switch is selected in “IG −ON” mode.
 When the parking brake is applied ...
GS430—This light comes on fo r a few seconds when the
engine is started even after the parking brake is released.
GS300—This light comes on fo r a few seconds when the
engine switch is selected in “IG −ON” mode even after the
parking brake is released.
If you drive your vehicle without releasing the parking brake,
the buzzer sounds and the message “PARK BRAKE” appears
on the multi −information display.
 When the brake fluid level is low ...
CAUTION
It is dangerous to continue driving normally when the
brake fluid level is low.
Have your vehicle checked at your Lexus dealer in the
following case:
The light does not come on even if the parking brake is
applied when the engine is started.
 The light does not come on even if the engine is started with
the parking brake released.

Page 96 of 622

GAUGES, METERS AND SERVICE REMINDER INDICATORS
75
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If either of the following conditions occurs, immediately
stop your
vehicle at a safe place and contact your Lexus
dealer.
 The light does not turn off even after the parking
brake is released while the engine is running.
In this case, the brakes may not work properly and
your stopping distance will become longer. Depress
the brake pedal firmly and bring the vehicle to an
immediate stop.
 The brake system warning light remains on together
with the “ABS” warning light.
In this case, not only the antilock brake system will
fail but also the vehicle will become extremely
unstable during braking.
GS430 only—Any of the following conditions may occur,
but do not indicate the malfunction:
The light may stay on for about 60 seconds after the engine
is started. It is normal if it turns off after a while.
 Depressing the brake pedal repeatedly may turn on the
warning light and buzzer. It is normal if the light turns off and
the buzzer stops sounding after a few seconds. 
You may hear a small sound in the engine compartment
after the engine is started or the brake pedal is depressed
repeatedly. This is a pump pulsating sound of the brake
system, and it is not a malfunction.
(b) Brake System Warning Light (yellow)
The light comes on when the engine switch is selected in
“IG−ON” mode.
GS430—If the engine is started, and the traction control
system, vehicle stability control system and hill −start assist
control system work properly, the light turns off after a few
seconds. Thereafter, if any part of the system malfunctions,
the light comes on again.
GS300—If the engine switch is selected in “IG −ON” mode, and
the traction control system, vehicle stability control system and
hill −start assist control system work properly, the light turns off
after a few seconds. Thereafter, if any part of the system
malfunctions, the light comes on again.
Although it is no problem to continue driving, have your vehicle
checked by your Lexus dealer as soon as possible.
(c) Driver’s Seat Belt Reminder Light and Buzzer
The light and buzzer act as a reminder to have the driver buckle
up the seat belt.

Page 98 of 622

GAUGES, METERS AND SERVICE REMINDER INDICATORS
77
(f) Discharge Warning Light
This light warns that the battery is being discharged.
If it comes on while you are driving, stop the vehicle, turn off the
engine, and check for the cause. Look first at the engine drive
belt.
 If it is loose or broken, the generator will not charge the
battery properly.
 If the belt is O.K., there is a problem somewhere in the
charging system.
The engine ignition will continue to operate, however, until the
battery is discharged. Turn off the air conditioning, blower,
radio, etc., and drive directly to the nearest Lexus dealer or
repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken
or loose.
(g) Malfunction Indicator Lamp
This lamp comes on when the engine switch is selected in
“IGON” mode and goes off after the engine starts. This
means that the warning light system is operating properly.
If the lamp remains on, or the lamp comes on while
driving, first check the followings:
 Empty fuel tank
If the fuel tank is empty, refuel immediately.
 Loose fuel tank cap
If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction
indicator lamp will go off after taking several driving trips.
If the lamp does not go off even after several trips, contact your
Lexus dealer as soon as possible.
If the fuel tank is not empty or the fuel tank cap is not
loose...
 There is a problem somewhere in the engine, emission
control system, electronic throttle control system, automatic
transmission electrical system or warning light system itself.
Contact your Lexus dealer as soon as possible to service the
vehicle.
If this lamp comes on and engine speed does not increase
when the accelerator pedal is depressed, there may be a
problem somewhere in the electronic throttle control system.

Page 99 of 622

GAUGES, METERS AND SERVICE REMINDER INDICATORS
78At this time, vibration may occur. However, if you depress the
accelerator pedal more firmly and slowly, you can drive your
vehicle at low speeds. Have your vehicle checked by your
Lexus dealer as soon as possible.
Even if the abnormality of the electronic throttle control system
is corrected during low speed driving, the system may not be
recovered until the engine is stopped and the engine switch is
selected in “ACC” or “OFF” mode.
Emissions inspection and maintenance (I/M) programs
Your vehicle may not pass a state emission inspection if the
malfunction indicator lamp remains on. Contact your Lexus
dealer to check your vehicle’s emission control system and
OBD (On
−Board Diagnostics) system before taking your
vehicle for the inspection.
For details, see “Emissions inspection and maintenance (I/M)
programs” on page 497.
(h) Master Warning Light
If any system malfunctions, this warning light comes on or
flashes together with a warning tone, and a warning message
appears on the multi−information display. When the cause of
the problem is eliminated, the warning tone and message on
the display will turn off.
(i) ”ABS” Warning Light
The light comes on when the engine switch is selected in
“IG−ON” mode.
GS430—If the anti−lock brake system and the brake assist
system work properly, the light turns of f in a few seconds after
the engine is started. Thereafter, if either system malfunctions,
the light comes on again.
GS300—If the anti−lock brake system and the brake assist
system work properly, the light turns of f in a few seconds after
the engine switch is selected in “IG−ON” mode. Thereafter, if
either system malfunctions, the light comes on again.
When the “ABS” warning light is on, the anti− lock brake system
and the brake assist system do not operate, but the brake
system still operates conventionally.
If either of the following conditions occur, this indicates a
malfunction somewhere in the components monitored by
the warning light system. Contact your Lexus dealer as
soon as possible to service the vehicle.
 The light does not come on when the engine switch is
selected in “IG −ON” mode.
 The light remains on after the engine is started (GS430), or
remains on after the engine switch is selected in “IG −ON”
mode (GS300).
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.

Page 100 of 622

GAUGES, METERS AND SERVICE REMINDER INDICATORS
79
CAUTION
If the “ABS” warning light remains on together with the
brake system warning light (red), immediately stop your
vehicle at a safe place and contact your Lexus dealer.
In this case, not only the antilock brake system will fail
but also the vehicle will become extremely unstable
during braking.
GS430 only—Either of the following conditions may
occur, but does not indicate a malfunction:
 The light may stay on for about 60 seconds after the engine
is started. It is normal if it turns off after a while.
 Depressing the brake pedal repeatedly may turn on the
light. It is normal if it turns off after a few seconds.
(j) Open Door Warning Light
This light remains on until all the doors are completely closed.
(k) Adaptive Front Lighting System Off
Indicator Light
This light comes on when yo u turn off the Adaptive Front
Lighting System (AFS) by pushing the “AFS OFF” switch.
If there is a problem somewhere in the Adaptive Front Lighting
System (AFS) or automatic headlight leveling system, the light
flashes. At this time, both systems do not operate properly.
Although it is no problem to continue driving, have your vehicle
checked by your Lexus dealer as soon as possible.
(l) Low tire pressure warning light
This light comes on when the engine switch is selected in
“IG−ON” mode. If the tire pressure warning system works
properly and tire inflation pressure is appropriate, the light
goes off after a few seconds.
This light comes on or flashes in the following cases when the
engine switch is selected in “IG −ON” mode.
 When the low tire inflation pressure is detected while
driving...
If any tire has low inflation pressure, the light comes on.
The light goes off after the tire inflation pressure is adjusted
to a specified level.
 When initializing the system...
If initialization is completed, the light blinks three times.
 When the system malfunctions...
If the system malfunctions, the light blinks.

Page:   1-10 11-20 21-30 31-40 41-50 ... 80 next >