set clock Lexus GX470 2003 Basic Functions / LEXUS 2003 GX470 OWNER'S MANUAL (OM60A45U)

Finish
GAUGES, METERS AND SERVICE REMINDER INDICATORS
54The multiinformation display provides various
information, including clock, outside temperature, and
your vehicle’s driving condition.
When the ignition switch is on, the last previously used mode
displayed just before the ignition switch is off will appear.
If the electrical power source has been disconnected from the
multi−information display, the
display will automatically be set
to the initial mode.
When the instrument panel lights are turned on, the brightness
of the display will be reduced.
You can adjust the brightness of the display. To adjust the
brightness, see “ADJUSTING THE BRIGHTNESS OF THE
DISPLAY” below. ADJUSTING THE BRIGHTNESS OF THE DISPLAY
The key must be in the “ACC” or “ON” position. To adjust the
brightness of
the display, push and hold the “MODE” button for
more than 2 seconds. “ILL” will appear on the display.
To increase the brightness − Push the “
” button.
To decrease the brightness − Push the “
” button.
You can adjust the brightness to 3 levels (when the tail lights
are off) or 6 levels (when the tail lights are on).
After adjusting, the display automatically return to the previous
display.
CAUTION
Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.

Finish
GAUGES, METERS AND SERVICE REMINDER INDICATORS
55
Clock
The digital clock indicates the time when the key is in the
“ACC” or “ON” position.
To reset the time, push and hold the “MODE” button for 2
seconds. “ILL” will appear on the display. Then push the
“MODE” button once. The time will blink.
To reset the hour − Push the “
” button.
To reset the minutes − Push the “
” button.
To adjust the time to the nearest hour, push the “RESET”
button. For example, if the “RESET” button is depressed when
the time is between 1:01 − 1:29, the time will change to 1:00.
If the time is between 1:30 − 1:59, the time will change to 2:00.
If the electric power source has been disconnected, the time
display will automatically be set to 1:00.
Outside temperature and cruise information
The following information is shown with the ignition
switch turned on. Each time you push the “MODE” button,
the display toggles through this information.
 Outside temperature mode
 Average fuel consumption mode
 Instantaneous fuel consumption mode
 Driving range mode
 Average vehicle speed mode
 Barometer mode
 Altimeter mode
 Elapsed time mode
The displayed values indicate general driving conditions.
Accuracy varies with driving habits and road conditions.

EXTERIOR EQUIPMENT
85
2. To remove the fuel tank cap, turn the cap
counterclockwise by 90 degrees (to the pressure point
1
), and then turn it an additional 30 degrees (to
point 2
). Pause slightly before removing it.
Although a click will be heard as you turn the cap to point
1
,
it does not indicate that the cap can be removed.
It is not unusual to hear a slight swoosh when the cap is
opened.
15PY017
3. The removed cap can be stored on the back side of the
fuel filler door.
Position the cap so that the hooks point to the left and right or
up and down, and set it in the receptacle on the back side of
the door.

IN CASE OF AN EMERGENCY
365
Make sure to set the jack properly in the jack point.
Raising the vehicle with jack improperly positioned
will damage the vehicle or may allow the vehicle to fall
off the jack and cause personal injury.
 Never get under the vehicle when the vehicle is
supported by the jack alone.
 Use the jack only for lifting your vehicle during wheel
changing.
 Do not raise the vehicle with someone in the vehicle.
 When raising the vehicle, do not place any objects on
top of or underneath the jack.
 Raise the vehicle only high enough to remove and
change the tire.
NOTICE
Do not continue driving with a deflated tire. Driving
even a short distance can damage a tire and wheel
beyond repair.
 When jacking up or installing tire chains, be sure to
turn off the rear height control air suspension with
the “HEIGHT CONTROL OFF” switch and stop the
engine. Otherwise, the vehicle height may change
because of the automatic leveling function resulting
in accident.
40PY040
 1 Jack

2 Spare tire

3 Tool tray
1. Get the tool, jack and spare tire.
To remove the tool tray, turn the knob counterclockwise and
open the cover, then pull the tray out.